Stone Forest PFS-TD-24 WSD6 Series User manual

PFS-TD-24-xx-WSD6 (formerly PFS-TDD6SLF-24)
PFS-TD-24-xx-WSD6 (formerly PFS-TDD6SLF-36)

1. Usingwhiteglovesprovided,carefullylayoutallbrassornickelfittings
onaprotectedsurface.Someassemblywillberequiredusingthe
includedallenwrench.



2.Startwiththefrontlegs.Thesecomepre‐assembledwiththebottomcollars
settosupportthedrawer6”fromtheground.Theheightofthecollarscan
beadjustedusingthesetscrewtosuitdesireddesignandspace.Iftheyare
moved,theincludedtemplatewillnolongerbeaccurate.



3. Carefullyslidethelegsthroughthedrawerunitfromthebottom.supplied2x2”(1of2)
We’veincluded2pcsof2x2woodcutto6”tohelpwiththeinitiallocation
ofthedraweronthewall.



4.Movethedrawerandlegsintoposition.Removethedrawerfromthe
cabinetandlevelthebackedgeofthedrawer.Oncelevel,usethesuppliedsupplied2x2”(1of2)
screws(andanchorsifneeded)toattachthecabinettothewall.Forthe
strongestinstallation,werecommendlocatingatleastonestudalongthe
thebackofthecabinetandpredrillinga1/8”holeinthecabinetback.
Atthispointyoucantwistthefrontfeettohelplevelfronttoback.

5.Withdrawerunitinplace,findandaffixtheincludedtemplateontothe
wallusingthe24”or36”edgemarksdependingonthewidthofthe
standpurchased.Thistemplate(onlyifusedwithpre‐setheights)will
helplocatesuggestedwasterough‐inaswellasthecenterlinesforthewall
returns.

6.Slidethe2additionalcollarscarefullyontothefrontlegs.Measuringdown
fromthetopofthecollarstothetopofthedrawer,setat5½”using
suppliedallenwrench.

7.Slidethewoodshelfdownontothefrontlegs.Checktheshelfatthefront
forlevelandadjustthecollarsasneeded.Additionalshelfcollars
Then,withsomehelpinghands,leveltheshelfatthebackANDfronttoback.
Whileyourhelpisholdingtheshelfinposition,markthewallonthe
undersidenotingthepositionofthemetalbracket.
Removetheshelfthenremovethebracketfromtheshelfandmount
thebrackettothewallwherepreviouslymarked.Installtheshelfbackonto
thelegsandbracketandattach.
8.Setthereturnarmsontothefrontlegs.Theapproximatelocationsofthe
wallescutcheonsaremarkedonthetemplate.Pleaseverifythatthearms
arelevelbeforemarkinganddrillingholesforthesuppliedbrassscrews
andanchors.Ifdrillingintowoodblockingorstuds,please
pre‐drilltheholeswitha7/64”bit.Thiswillhelpwiththeinstallation
ofthesofterbrassscrews.Ifgoingintodrywall,usethesuppliedanchors
andpre‐drillusing3/16”bit.
9.Installsinktopandbracketaccordingtothesinkmodel.Thestonesinksare
counterboredontheundersidetoacceptthetop3/8”ofthefrontlegs.The
collarsdirectlyunderthesinksdonotsupportanyweight.Thesecanbe
adjustedupagainstthesinkbottomwhenyouaredonewiththefinalassembly.