Storm VUDO2PTZIR30X User manual

VUDO2PTZIR30X
2.1MP Full HD 30X PTZ IP Dome Camera with IR
Installation Manual
Version 1.0.1

i
Table of Contents
1 IR INTELLIGENT SPEED DOME INSTALLATION .............................................1
1.1 Installation Preparation .........................................................................................................................1
1.2 Check Accessories................................................................................................................................2
1.3 Open the Device ....................................................................................................................................2
1.4 Dial Switch Setup (For Analog Speed Dome Only)..........................................................................2
1.4.1 Initial Setup........................................................................................................................................3
1.4.2 Dial Switch Setup (For Intelligent Speed Dome Only).................................................................3
1.4.3 Baud rate and Parity Setup .............................................................................................................4
1.4.4 Speed Dome Address Setup...........................................................................................................4
1.4.5 Terminal Matched Resistance Setup.............................................................................................4
1.5 Reset and SD Card Installation (For network speed dome only) ...................................................5
1.6 Speed Dome Installation ......................................................................................................................6
1.6.1 Quick Installation port.......................................................................................................................6
1.6.2 Cable Connection .............................................................................................................................7
1.6.3 Install the speed dome.....................................................................................................................8
2 BRACKET DIMENSIONS ................................................................................. 10
2.1 Wall Mount Bracket .............................................................................................................................10
2.2 Hanging Mount Bracket (Multiple Lengths)......................................................................................10
2.3 Corner Mount Bracket.........................................................................................................................11
2.4 Pole Mount Bracket .............................................................................................................................12

i
3 WALL MOUNT BRACKET INSTALLATION...................................................... 14
3.1 Component Installation .......................................................................................................................14
3.2 Installation.............................................................................................................................................14
3.2.1 Installation Requirements..............................................................................................................14
3.2.2 Installation Steps.............................................................................................................................14
4 HANG MOUNT BRACKET INSTALLATION ..................................................... 17
4.1 Component Installation .......................................................................................................................17
4.2 Installation.............................................................................................................................................17
4.2.1 Installation Requirements..............................................................................................................17
4.2.2 Installation Steps.............................................................................................................................17
5 CORNER MOUNT BRACKET INSTALLATION ................................................ 20
5.1 Component Installation .......................................................................................................................20
5.2 Installation.............................................................................................................................................20
5.2.1 Installation Requirements..............................................................................................................20
5.2.2 Installation Steps.............................................................................................................................20
6 POLE MOUNT BRACKET INSTALLATION ...................................................... 23
6.1 Installation.............................................................................................................................................23
6.1.1 Installation Requirements..............................................................................................................23
6.1.2 Installation Steps.............................................................................................................................23
7 APPENDIX Ⅰ LIGHTNING PROOF AND SURGE PROTECTION ..................... 26
8 APPENDIX Ⅱ ABOUT RS485 BUS ................................................................... 27

i
8.1 RS485 Bus Main Feature ...................................................................................................................27
8.2 RS485 Bus Transmission Distance ..................................................................................................27
8.3 The Problem in Practical Use ............................................................................................................27
8.4 RS485 Bus FAQ ..................................................................................................................................28
9 APPENDIX Ⅲ THE RELATIONSHIP BETWEEN THE 24V AC CABLE
DIAMETER AND THE TRANSMISSION DISTANCE .............................................. 29
10 APPENDIX Ⅳ THE RELATIONSHIP BETWEEN THE 12V DC CABLE
DIAMETER AND THE TRANSMISSION DISTANCE .............................................. 31
11 APPENDIX IV WIRE GAUGE REFERENCE SHEET ....................................... 33

ii
iv
Welcome
Thank you for purchasing our speed dome!
Please read the following safeguards and warnings carefully before you install or use the
product

ii
v
Important Safeguards and Warnings Safety
Measures
1. Qualified Engineer Needed
The installation engineer or maintenance engineer shall have corresponding CCTV system
installation certificate or maintenance qualification certificate.
The installation engineer or maintenance engineer shall have qualification certificate for work
at height.
The installation engineer or maintenance engineer shall have the basic knowledge and
operation technique for low-voltage cable layout and low-voltage electronic cable connection.
Please read the installation manual carefully and keep it well for futurereference,
We are not liable for any problems caused by unauthorized modifications or attempted repair.
2. Lifting Appliance Requirement
Please select the proper speed dome installation mode and use the lifting appliances at the
safety environment.
The lifting appliances shall have the enough capacity to reach the installationheight.
The lifting appliances shall have safe performance.
The precaution measures include two types: Warning and Note.
Warning: It is to alert you there is an optional risk of death or seriesinjury!
Note: It is to alert you there is an optional risk of damage or propertyloss!
Warning
1. All installation and operation here should conform to your local electrical safety codes. We
assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
2. Be sure to use all the accessories (such as power adapter) recommended bymanufacturer.
3. Laser light is dangerous; please do not look at itstraight.
4. Do not connect several speed domes to one power adapter. It may result in overheat or fire
if it exceeds the rated load.
5. Before you connect the cable, install or uninstall, or begin the daily maintenance work,
please turn off the power and unplug the powercable.
6. Please make sure the produce is secure firmly on the wall or theceiling.

ii
vi
7. Please turn off the power and unplug the power cable, If there is any smoke, disgusting
smell, or noise. Please contact your local retailer or customer service centre forhelp.
8. All the examination and repair work should be done by the qualified service engineers. We
are not liable for any problems caused by unauthorized modifications or attempted repair.
Note
1. Safety Transportation
Heavy stress, violent vibration or water splash are not allowed during transportation, storage
and installation.
This series product must use split type package during thetransportation.
We are not liable for any damage or problem resulting from the integrated package during
the transportation.
2. When device is malfunction
Shut down the device and disconnect the power cable immediately if there is smoke, abnormal
smell or abnormal function. Please contact your local retailer ASAP.
3. Do not try to dismantle or modify the device
There is risk of personal injury or device damage resulting from opening the shell.
Please contact your local retailer if there is internal setup or maintenancerequirement.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
4. Do not allow other object falling into the device
Please make sure there is no metal or inflammable, explosive substance in the speed dome.
The above mentioned objects in the device may result in fire, short-circuit ordamage.
Please shut down the device and disconnect the power cable if there is water or liquid falling
into the camera. Please contact your local retailerASAP.
Please pay attention to the camera. Avoid the sea water or rain to erode thecamera.
5. Handle carefully
Do not allow this series product fall down to the ground.
Avoid heavy vibration.
6. Installation Environment Requirement
This series speed dome should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
This series product shall be away from the strong electromagnetism radiant, please keep it
away from wireless power, TV transmitter, transformer and etc.
7. Daily Maintenance

vii
Please use the soft cloth to clean dust on the shell, or you can use soft cloth with cleaning
liquid to clean the shell and then use soft cloth to make itdry.
Do not use gasoline, dope thinner or other chemical material to clean the shell. It may result
in shell transfiguration or paint flake.
Do not allow the plastic or rubber material to touch the shell for a long time. It may result in
paint flake.
It is highly recommended to use the product with a lightning-proof device, which can realize
better lightning-proof effect.

1
1 IR INTELLIGENT SPEED DOME INSTALLATION
1.1 Installation Preparation
Basic Requirement
All installation and operation here should conform to your local electrical safetycodes.
Before installation, please open the package and check all the components are included.
Please make sure the speed dome installation environment and installation mode can meet
your requirement. If there is special requirement, please contact your local retailer for more
information.
We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
Check installation space and installation location intension
Please make sure the installation environment has enough space to install the speed dome and
its corresponding bracket.
Please make sure the ceiling, wall and the bracket can support the speed dome and its
corresponding installation component. It shall sustain the 8X weight of the speed dome. Please
notice that the installation height should be more than 6m if it is a laser speed dome.
About cable
Please select the cable according to your transmission distance.
The minimum video coaxial-cable requirement is:
75 ohm.
Full cable with copper conductor
95% knitted copper shield
International Model
Max Distance
(Ft\M)
RG59/U
750ft (229m)
RG6/U
1,000ft (305m)
RG11/U
1,500ft (457m)
Please refer to appendix 2 for more information about RS485 communication cable.
Select proper power supply cable according to transmission distance
Refer to appendix 3 for 24VAC power supply device.
Refer to appendix 4 for 12VDC power supply device.
Please keep all package material well for future use
Please keep speed dome package material well in case you need to send it back to your local
retailer or manufacturer for maintenance work.
Non-original package material may result in device damage during the transportation.

2
1.2 Check Accessories
Before the installation, please check the accessories one by one according to the packing list.
Please make sure all the components listed are includes.
1.3 Open the Device
Please open the box and then take out the speed dome. See Figure 1-1.
Figure 1-1
Note:
There are two types of IR intelligent speed dome which are shown in Figure 1-1, please refer to
the actual object for details.
There is laser light and IR light on the laser speed dome, the laser light is used for light
compensation while the IR light can be used to indicatewhether the laser lightis on or off, the laser
light is enabled when the IR light is on.
1.4 Dial Switch Setup (For Analog Speed Dome Only)
Open the cover of the speed dome; you can see there are two dial switch buttons. You can use
them to set intelligent speed dome parity, baud rate, address and etc.
Note:
When HDCVI intelligent speed dome only uses coaxial control, dial-up and other related RS485

3
setup don’t have to be conducted.
1.4.1 Initial Setup
Address: 1
Baud rate: 9600
Parity: None
120Ωmatched resistance：OFF
1.4.2 Dial Switch Setup (For Intelligent Speed Dome Only)
Users must set the address, Baud rate and parity which are used by the speed dome before
controlling it. Only after all these setup, can the speed dome respond to its control commands.
Note:
Users must reboot the speed dome after resetting some specifications, which makes the new
setup take effect.
There are two dial switch buttons on the speed dome PTZ which are used to confirm the
specifications of address and Baud rate, parity. It is 1 when you set the button as ON. For address
setup dial-up, 1 is the lowest bit, 8 is the highest bit; for the Baud rate and parity setup dial-up, 1 is
the lowest bit, 4 is the highest bit, see Figure 1-2. (Intelligent speed dome self- adaptive PELCO-
D, PELCO-P, industrial standard protocol, control protocol don’t need dial switch setup).

4
1.4.3 Baud rate and Parity Setup
Figure 1-2
It is used to set speed dome Baud rate and parity. 1 and 2 bits are used to set Baud rate while 3
and 4 bits are used to set parity, see Figure 1-3.
Figure 1-3
Please refer to the baud rate setup sheet1-1 for detailed information.
1
2
Baud rate
OFF
OFF
9600bps
ON
OFF
4800bps
OFF
ON
2400bps
ON
ON
1200bps
Sheet 1-1
Please refer to the parity setup sheet 1-2 for detailed information.
3
4
Parity
OFF
OFF
NONE
ON
OFF
EVEN
OFF
ON
ODD
ON
ON
NONE
1.4.4 Speed Dome Address Setup
Figure 1-4
See Figure 1-4 for address setup. The speed dome uses dial switch to set address, the encode
mode adopts binary system. 1 to 8 is valid bit. The highest address bit is 255. Youcan refer to the
following sheet 1-3 for more information.
Address
1
2
3
4
5
6
7
8
1
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
5
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
6
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
7
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
……
…………………………………………………………………
254
OFF
ON
ON
ON
ON
ON
ON
ON
255
ON
ON
ON
ON
ON
ON
ON
ON
Sheet 1-3
1.4.5 Terminal Matched Resistance Setup
The connection mode of device terminal 120Ω resistance is equipped on the power board. There

5
are two connection modes which are shown in Figure 1-5.
1-2
2-3
120Ω
ON
OFF
Figure 1-5
The factory default connection mode is shown in Figure 1-6, the jumper (connection board) is
plugged into pin2 and pin 3, which means 120Ω resistance is not connected to the device.
Figure 1-6
If you want to connect the 120Ω resistance, you have to pull the jumper out of pin 2 and pin 3,
and connect to pin 1 and pin 2, then 120Ω resistance is connected to the circuit, see Figure 1-7.
Figure 1-7
1.5 Reset and SD Card Installation (For network speed dome only)
You can see there is a RESET button and Micro-SD card slot on the PCB after you open the dial
switch cover. See Figure 1-8. Reset button is used to reset network system. Micro-SD card is
used to save the data.

6
Figure 1-8
1.6 Speed Dome Installation
Note:
The installation of this section can be applied to IR Analog Intelligent and IR Network Intelligent
Speed Dome.
The speed dome has various brackets suitable for different environments. For detailed
information, please refer to chapter 3 to chapter 8. Here we are going to install the analog speed
dome with the wall mount bracket.
1.6.1 Quick Installation port
Now you can install the quick installation port. Please twist Teflon tape around the screw thread
of the quick installation port and turn it into the screw thread of the wall mount bracket. Use M4
stainless screws to secure firmly. See Figure 1-9.

7
Figure 1-9
1.6.2 Cable Connection
Connect the safety hook of the IR speed dome cover to the hook of the quick installationport.
Connect the reserved integration cable of the wall mount bracket to the corresponding power
cable, video/audio cable, RS485 control cable, alarm port, high frequency cable, fiber cable
(if necessary) of the multiple-function composite cable of the IR speed dome. Paste the
insulating tape in the connection position to do the proper waterproof work. See Figure1-10.
Figure 1-10

8
Note
The video port is covered the heat shrink tube of high shrinking ratio. After the video
connection, please heat the tube to make sure the video port is damp proof and water
proof.
1.6.3 Install the speed dome
Step 1
Pull the integration cable and multiple-function composite cable to the wall mount bracket slowly.
Step 2
Line up the straight edge of the flange of the IR speed dome to the straight edge of the quick
installation port, and then push the speed dome to the bottom of the port slowly.
Step 3
Use your hands to turn the M6*14 stainless screw (with spring washer) to the Ф6.5 hole of the
straight edge of the IR speed dome. Turn other two M6*14 stainless screws to groove of IR speed
dome flange. Use the inner hex tool to fix these three stainless screws. Now you have completed
the installation. See Figure 1-11.
Step 4
Please make sure:
Figure 1-11
The three stainless screws of the quick installation port are firmlysecure.
The IR speed dome is fixed.
The speed dome is straight.
The steel wire connection is firm.
After your installation, the interface is shown as in Figure 1-12.

9
Figure 1-12

10
2 BRACKET DIMENSIONS
2.1 Wall Mount Bracket
The wall mount bracket dimensions are shown as below. See Figure 2-1.
Figure 2-1
2.2 Hanging Mount Bracket (Multiple Lengths)
The hanging mount bracket is shown as below. See Figure 2-2.

11
Figure 2-2
Note:
The bracket length setup values are:
200mm (default)
400mm (optional)
You just need to replace the connection pole
2.3 Corner Mount Bracket
The corner mount bracket is shown as below. See Figure 2-3.

12
Figure 2-3
2.4 Pole Mount Bracket
The pole mount bracket is shown as below. See Figure 2-4.