Stow CX22DUO Guide

OPERATION AND PARTS MANUAL
DUO HAND MIXERS
CX22DUO
CX22DUOE
CX44DUO
CX44DUOE
Revision #1 (06/15/07)
PARTS DEPARTMENT:
800-427-1244
FAX: [phone]
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
800-478-1244
FAX:[phone]
STOW CONSTRUCTION EQUIPMENT
A DIVISION OF STOW INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 888-252-STOW [888-252-7869]
FAX: [phone] • FAX:[phone]
E-MAIL: [e-mail] • WWW: stowmfg.com

CX22/CX44 DUO HAND MIXER — SILICOSIS WARNING
Grinding/cutting/drilling of masonry, concrete, metal and
other materials with silica in their composition may give
off dust or mists containing crystalline silica. Silica is a
basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Repeated and/or
substantial inhalation of airborne crystalline silica can
cause serious or fatal respiratory diseases, including
silicosis. In addition, California and some other
authorities have listed respirable crystalline silica as a
substance known to cause cancer. When cutting such
materials, always follow the respiratory precautions
mentioned above.
WARNING
Grinding/cutting/drilling of masonry, concrete, metal and
other materials can generate dust, mists and fumes
containing chemicals known to cause serious or fatal
injury or illness, such as respiratory disease, cancer,
birth defects or other reproductive harm. If you are
unfamiliar with the risks associated with the particular
process and/or material being cut or the composition of
the tool being used, review the material safety data
sheet and/or consult your employer, the material
manufacturer/supplier, governmental agencies such as
OSHA and NIOSH and other sources on hazardous
materials. California and some other authorities, for
instance, have published lists of substances known to
cause cancer, reproductive toxicity, or other harmful
effects.
Control dust, mist and fumes at the source where
possible. In this regard use good work practices and
follow the recommendations of the manufacturers or
suppliers, OSHA/NIOSH, and occupational and trade
associations. Water should be used for dust
suppression when wet cutting is feasible. When the
hazards from inhalation of dust, mists and fumes cannot
be eliminated, the operator and any bystanders should
always wear a respirator approved by NIOSH/MSHA for
the materials being used.
WARNING
SILICOSIS WARNING RESPIRATORY HAZARDS

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 3
CX22/CX44 DUO HAND MIXER — TABLE OF CONTENTS
Component Drawings
Mixer Assembly (CX22) ..................................... 16-19
Mixer Assembly (CX44) ..................................... 20-23
Terms and Conditions of Sale - Parts ..................... 24
Specification and part number
are subject to change without
notice.
NOTE
STOW CX22/CX44 DUO
HAND MIXER
Silicosis Warning ....................................................... 2
Table Of Contents ..................................................... 3
Parts Ordering Procedures ....................................... 4
Safety Message Alert Symbols ................................. 5
Rules For Safe Operation ...................................... 6-7
Specifications ............................................................ 8
General Information .................................................. 9
Components............................................................ 10
Setup ....................................................................... 11
Operation ................................................................ 12
Maintenance ........................................................... 13
Explanation Of Code In Remarks Column .............. 14
Suggested Spare Parts ........................................... 15

PAGE 4 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)
When ordering parts,
please supply the following information:
❒❒
❒❒
❒Dealer account number
❒❒
❒❒
❒Dealer name and address
❒❒
❒❒
❒Shipping address (if different than billing address)
❒❒
❒❒
❒Return fax number
❒❒
❒❒
❒Applicable model number
❒❒
❒❒
❒Quantity, part number and description of each part
❒❒
❒❒
❒Specify preferred method of shipment:
✓FedEx or UPS Ground
✓FedEx or UPS Second Day or Third Day
✓FedEx or UPS Next Day
✓Federal Express Priority One
✓DHL
✓Tr u ck
Here’s how to get help...
Please have the model and serial number on
hand when calling.
Parts Department
800-427-1244 Fax: [phone]
310-537-3700 Fax: [phone]
Service Department
800-478-1244 Fax: [phone]
310-537-3700
Technical Assistance
800-478-1244 Fax: [phone]
Warranty Department
800-421-1244, Ext. 279 Fax: [phone]
310-537-3700, Ext. 279
Sales Department
310-661-4242 Fax: [phone]
877-289-7869 (877-BUY-STOW)
Note:Unless otherwise indicated by customer, all
orders are treated as “Standard Orders”, and will
ship within 24 hours.We will make every effort to
ship “Air Shipments” the same day that the order is
received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.
Extra Discounts!
All parts orders which include complete part numbers
and are received by our automated web parts order
system, or by fax qualify for the following extra
discounts:
Ordered Standard Stock orders
via orders ($750 list and above)
Fax 3% 10%
Web 5% 10%
Special freight allowances
when you order 10 or more
line items via Web or Fax!**
FedEx Ground Service at no charge for freight
No other allowances on freight shipped by any other
carrier.
Place Your Parts Order Via Web or Fax
For Even More Savings!
NOTE:DISCOUNTS ARE SUBJECTTO CHANGE
Direct TOLL-FREE access
to our Parts Department:
Toll-free nationwide — 800-427-1244
STOW CONSTRUCTION EQUIPMENTSTOW CONSTRUCTION EQUIPMENT
STOW CONSTRUCTION EQUIPMENTSTOW CONSTRUCTION EQUIPMENT
STOW CONSTRUCTION EQUIPMENT
A DIVISION OF STOW INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 888-252-STOW [888-252-7869]
FAX: [phone] • FAX: [phone]
E-MAIL: [e-mail] • WWW: stowmfg.com
CX22/CX44 DUO HAND MIXER — PARTS ORDERING PROCEDURES

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 5
Accidental Starting
ALWAYS place power ON/OFF switch in the
OFF position when the mixer is not in use.
Respiratory Hazard
ALWAYS wear approved respiratory
protection.
Equipment Damage Messages
Other important messages are provided throughout this manual
to help prevent damage to your mixer, other property, or the
surrounding environment.
ALWAYS wear approved eye and hearing
protection.
Sight and Hearing hazard
CX22/CX44 DUO HAND MIXER — SAFETY MESSAGE ALERT SYMBOLS
Safety precautions should be followed at all times when
operating this equipment. Failure to read and understand the
Safety Messages and Operating Instructions could result in
injury to yourself and others.
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!
This Manual has been developed
to provide complete instructions for
the safe and efficient operation of
the STOW
Model CX22/CX44 DUO
HAND MIXER.
Before using this mixer,
ensure that the operating
individual has read and
understands all instructions in
this manual.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
HAZARD SYMBOLS
Potential hazards associated with the STOW CX22/CX44 DUO
HAND MIXER operation will be referenced with Hazard Symbols
which appear throughout this manual, and will be referenced in
conjunction with Safety Message Alert Symbols.
Rotating Parts
NEVER operate equipment with covers or
guards removed. Keep fingers, hands, hair and
clothing away from all moving parts to prevent
injury.
NOTE
This mixer, other property, or the
surrounding environment could
be damaged if you do not follow
instructions.
NOTE
You CAN be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
You CAN be INJURED if you DO NOT follow directions.
WARNING
CAUTION
You WILL be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
DANGER

PAGE 6 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)
■ ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
■ ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using mixer.
■ ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
■ NEVER leave the mixer unattended, turn off electric motor
when unattended.
■ CAUTION must always be observed while servicing this mixer.
Rotating parts can cause injury if contacted.
■ Unauthorized equipment modifications will void all
warranties.
■ Ensure that any extension cable is protected against damage
and not liable to be tripped over or trapped underneath the
mixer.
■ DO NOT allow extension cord to come into contact with water
or fluids.
■ DO NOT spray water onto electric motor.
■ Mixer must be used only for its intended purpose.
■ This mixer is not suitable for the mixing of flammable or
explosive substances.
■ NEVER operate the mixer in an explosive atmosphere.
■ Keep area around the mixer clear of obstructions which
could cause persons to fall onto
moving parts .
■ ALWAYS ensure mixer is on level ground before mixing.
■ Become familiar with the controls of the mixer before
operating.
■ ALWAYS disconnect AC power plug from power source
before moving mixer.
■ If mixer is equipped with an electric motor, operate electric
motor only at the specified voltage indicated on the nameplate.
■ Make sure the OFF/ON power switch on the electric motor is
always in the OFF position before inserting the mixer's power
plug into an AC receptacle (electric model only).
CX22/CX44 DUO HAND MIXER — RULES FOR SAFE OPERATION
■ NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
■ Manufacturer does not assume responsibility for any accident
due to equipment modifications.
The following safety guidelines should always be used when
operating the Multiquip CX22/CX44 Duo Hand Mixers.
GENERAL SAFETY
■ DO NOT operate or service this equipment before
reading this entire manual.
■ This equipment should not be operated by persons under 18
years of age.
■ NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
■ NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
■ NEVER operate this equipment under the influence or drugs or
alcohol.
■ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■ ALWAYS check the machine for loosened threads or bolts
before starting.
■ ALWAYS wear proper respiratory (mask)
hearing and eye protection equipment
when operating the mixer.
Failure to follow instructions in this manual may lead to
serious injury or even death! This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
DANGER

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 7
■ In emergencies always know the location of the
nearest phone or
keep a phone on the job site .
Also know the phone numbers of the nearest
ambulance , doctor and fire department . This
information will be invaluable in the case of an
emergency.
Maintenance Safety
■ NEVER lubricate components or attempt service on a running
machine.
■ ALWAYS allow the machine a proper amount of time to cool
before servicing.
■ Keep the machinery in proper running condition.
■ Fix damage to the machine immediately and always replace
broken parts, or missing decals.
■ Dispose of hazardous waste properly.
■ DO NOT use food or plastic containers to dispose of
hazardous waste.
Emergencies
■ ALWAYS know the location of the nearest fire extinguisher
and first aid kit.
CX22/CX44 DUO HAND MIXER — RULES FOR SAFE OPERATION

PAGE 8 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)
CX22/CX44 DUO HAND MIXER — SPECIFICATIONS
snoitacificepS44XC/22XC.1elbaT
ledoM EOUD22XC/OUD22XCEOUD44XC/OUD44XC
egatloVV032/V021-011V032/V021-011
sttaW000,1/008004,1
PH4/1/1.12
spmA4.4/2.
70.6/7.21
sraeG22
1raeG-daoLrednUMPR004-0053-0
2raeG-daoLrednUMPR025-0005-0
retemaiDlooTgnixiMdednemmoceR)mc21(se
hcni57.4)mc41(sehcni5.5
retemaiDkceNeldnipS)mc5(sehcni2)mc5(sehcni2
leveLerusserPdnuoS)A(Bd48)A(Bd48
leveLnoi
ssimEesioN)A(Bd79)A(Bd79
noitarbiVmrA-dnaHtf2.8<
2
m67.0(
2
)tf2.8<
2
m67.0(
2
)
noitcetorPlacirtcelEdetalusnI-elbuoDdetalusnI-elbuoD
yticapaCgnixiM)sretil94-91(snollag31-5)sretil59-83(s
nollag52-01
thgieW)gk7.7(bl71)gk5.9(bl12

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 9
CX22/CX44 DUO HAND MIXER — GENERAL INFORMATION
Application
The Stow CX22/CX44 Duo Hand Mixer is designed for mixing
of chemical building products of all standard viscosities
(liquid, pasty, viscous, powdery) used in the building industry
and building-related trades.
The right mixing tool should be selected depending on the
consistency of the material and the quantity to be mixed.
If used properly, the hand mixer will provide years of safe
and reliable service.
The CX22/CX44 is not to be used for the processing or
preparation of food or similar products. The machine is also
not suitable for mixing materials containing graphite powder,
hydrochloric solutions or liquid manure. Mixing such
materials can damage or destroy machine.
Paddles
The CX22DUO and CX22DUOE hand mixers come with
MKD120HF paddles. The MKD120HF paddles have a
diameter of 4 3/4 inches and are used to mix a volume of 5
to 13 gallons.The CX44DUO and CX44DUOE hand mixers
come with MKD140HF paddles. The MKD140HF paddles
have a diameter of 5 1/2 inches and are used to mix a volume
of 10 to 25 gallons.
Electrical
Make sure that the power being supplied to the motor
corresponds to the voltage rating label on the motor. Supplying
the wrong voltage to the electric motor will cause severe
electrical damage to the motor.
Always make sure the OFF/ON switch on the electric motor
is in the OFF position before applying power.
Extension Cables
The extension cable should be a 3-wire configuration that
includes a ground wire that conforms to UL code. Choose
the correct size of an extension cord as shown in Table 2.
Remember distance affects the wire size of the extension
cable.
Ensure that the extension cable is carefully laid out avoid-
ing
wet areas , sharp edges and locations where vehicles
might run over it.
Unroll the extension cable fully or it will overheat and could
catch fire. Make sure that all extension cable connections
are dry and safe. Replace any defective or worn-out exten-
sion cable immediately.
seziSdroCnoisnetxE.2ELBAT
erepmA
gnitaR
egnaR
stloV teeFnidroCfohtgneL
V511 .tF52 .tF05 .tF001 .tF051 .tF002 .tF052
V032 .tF05 .tF001 .tF002 .tF003 .tF004 .tF005
2-0 81 81 81 61 61 41
3-2 81 81 61 41 41 21
4-3 81 81 61 41 21 21
5-4 81 81 41 21 21 01
6-5 81 61 41 21 01 01
8-6 81 61 21 01 01 8
01-8 81 41 21 01 8 8
21-01 61 41 01 8 8 6
41-21 61 21 01 8 6 6
61-41 61 21 01 8 6 6
81-61 41 21 8 8 6 4
02-81 41 21 8 6 6 4

PAGE 10 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)
CX22/CX44 DUO HAND MIXER — COMPONENTS
Refer to Figure 1 for the location of the following mixer
components.
1. Ventilation Slits — These openings allow ventilation to
the unit to prevent overheating.
2. Safety Lock-off Button — When on, prevents the unit
from being operated accidentally.
3. Protection Frame — Protects the machine casing from
dirt and breakage.
4. ON/OFF Switch with Speed Control — Turns the power
on and off and regulates the mxing speed.
5. Gear Selection Lever — This lever is used to select the
gear (slow or fast) at which the unit is operating.
6. Protection Frame Fastening Screws — Holds the
protection frame securely in place.
7. Machine Neck — The mixing tools are attached to the
machine neck.
8. HEXAFIX® Quick Action Coupling — These connectors
attach the mixing tools to the machine neck.
9. Mixing Tools — These tools are used to mix chemical
building products.
Figure 1. Mixer Major Components

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 11
CX22/CX44 DUO HAND MIXER — SETUP
Assembly
Before using the hand mixer, the following steps need to be
performed.
1. Insert the mixing tools into the HEXAFIX coupling as
far as necessary to lock the tools in place, automatically
(see Figure 2).
2. When installing the mixing tools, make sure that the
blades are correctly positioned as shown in Figure 3.
3. When inserting mixing tools, also make sure that the
identifying marks on both the mixing shaft and the
mixing blades match as shown in Figure 4.
Figure 3. Positioning Blades
Figure 4. Matching Identifying Marks
Electric Connections
1. Connect the hand mixer power cable to a 110 V or
230V, 50/60 Hz power source, depending on the unit
you have. Make sure you conform to the specifications
on the nameplate of the mixer.
2. A 120V/230V power supply can also be used. Make
sure that the power supply conforms to the
specifications on the nameplate of the mixer. Voltage
decrease of more than 10% will cause loss of power
and overheating.
3. Use an extension cord (see Table 2) of adequate current
carrying capacity.
NEVER use a worn or frayed extension
cord. Insert the electric motor's power plug into one end of
the extension cord.
Figure 5. Extension Cord (Wet Hands)
To prevent personnel from tripping over
the extension cord, position the
extension cord so that it lays flat and is
not curled.
NOTE
DO NOT attempt to operate the mixer until the Safety, General
Information and Set-Up sections have been read and
understood.
CAUTION
NEVER touch the power cord (Figure 5) with wet hands or
while
standing in water when it is connected to a power
source.The possibly exists of electrical shock (electrocution)
even death.
NEVER spray water directly on the electric motor.
DANGER
CAUTION
Before plugging the power cable, check and make sure that
the ON/OFF switch operates properly and returns to the OFF
position when released.
Correct position of the blades
Figure 2. Inserting Mixing Tools
IDENTIFYING MARKS
SHOULD MATCH
IDENTIFYING MARKS
SHOULD MATCH
PULL BACK
INSERT

PAGE 12 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)
CX22/CX44 DUO HAND MIXER — OPERATION
1. To start , press the starting lockout button then press
the ON/OFF switch (Figure 6).The integrated electronic
controls will start the machine in a controlled speed.
2. To make the motor run faster, apply more pressure to
the ON/OFF switch.
3. To change the maximum speed, turn the gear selection
lever 180° (Figure 7). First gear is slow and second
gear is fast.
Figure 6. ON/OFF Switch
Figure 7. Gear Selection Lever
CAUTION
ALWAYS hold the machine with both hands while working.
4. When submerging the mixing tool in the mixing material
or when lifting out the mixing tool, always reduce the
speed. When the mixing tool is fully submerged,
increase the speed again to ensure that the motor is
adequately cooled.
5. During mixing, guide the mixer around the mixing
container (Figure 8). Continue mixing until all of the
material is completely mixed.
6. To stop the mixer, release the On/OFF switch.
7. Always clean the mixing tool after every use.
Figure 8. Mixing the Material
2.
1.
SLOW
FAST
GUIDE
MIXER
1
2
ON/OFF SWITCH
STARTING
LOCKOUT
BUTTON

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 13
1. Clean the machine and mixing tools after every use.
2. Keep the quick-action coupling clean and free of dust. Apply
grease to the hexagon mount regularly.
3. Keep the ventilation slits clean and free of foreign matter so
that machine can be properly cooled.
4. Replace the carbon brushes when worn. The machine is
equipped with self-deactivating carbon brushes. The ma-
chine will shut itself down when a certain level of wear is
reached, indicating that carbon brushes should be replaced.
5. Clean and lubricate gear care yearly or whenever servicing
requires that the gear case to be removed.
Mixer Storage
For storage of the mixer for over 30 days, the following is
recommended:
z Clean the mixer and mixing tools.
z Cover the mixer and place it a clean dry area, that is
protected from harsh elements.
CX22/CX44 DUO HAND MIXER — MAINTENANCE
ALWAYS disconnect the mixer from the power supply
before cleaning, changing the mixing paddles or
performing any maintenance.
CAUTION
To assure product safety and reliability, repairs,
maintenance, and adjustments should be performed by
an authorized service center or qualified technician to
prevent any misplaced wires and components that could
cause serious hazards.
CAUTION

PAGE 14 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)
EXPLANATION OF CODE IN REMARKS COLUMN
The contents and part numbers listed in the parts section are
subject to change
without notice . Multiquip does not
guarantee the availibility of the parts listed.
NOTE
When ordering a part that has more
than one item number listed, check
the remarks column for help in
determining the proper part to order.
QTY.Column
Numbers Used - Item quantity can be indicated by a number,
a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
REMARKS Column
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
Assembly/Kit - All items on the parts list with the same unique
symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
Serial Number Break - Used to list an effective serial number
range where a particular part is used.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use - Indicates that the part is used
only with the specific model number or model number variant
listed. It can also be used to show a part is NOT used on a
specific model or model number variant.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
The following section explains the different symbols and remarks
used in the Parts section of this manual. Use the help numbers
found on the back page of the manual if there are any questions.
NO. Column
Unique Symbols - All items with same unique symbol
(*, #, +, %, or >) in the number column belong to the same
assembly or kit, which is indicated by a note in the “Remarks”
column.
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general item,
such as different size saw blade guards in use or a part that
has been updated on newer versions of the same machine.
PART NO.Column
Numbers Used - Part numbers can be indicated by a number,
a blank entry, or TBD.
TBD (To Be Determined) is generally used to show a part that
has not been assigned a formal part number at time of
publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
Sample Parts List:
NO. PART NO. PART NAME QTY.REMARKS
1 12345 BOLT ....................... 1 .... INCLUDES ITEMS W/*
2*WASHER, 1/4 IN. ........... NOT SOLD SEPARATELY
2*12347 WASHER, 3/8 IN. .... 1 .... MQ-45T ONLY
3 12348 HOSE .................... A/R .. MAKE LOCALLY
4 12349 BEARING ................ 1 .... S/N 2345B AND ABOVE

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 15
CX22/CX44 DUO HAND MIXER — SUGGESTED SPARE PARTS
CX22/CX44 DUO HAND MIXER 1 TO 4 UNITS
Qty.P/N Description
2 ....... CM20509 ........... SPRING FOR BRUSH ASSY (CX22)
1 ....... CM20567 ........... BRUSH SET (CX22)
2 ....... CM20569 ........... BRUSH HOLDER (CX44)
1 ....... CM20566 ........... BRUSH SET (CX44)
NOTE
Part numbers on this Suggested
Spare Parts List may supercede/
replace the P/N's shown in the
test pages of this manual.

PAGE 16 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)
CX22 DUO HAND MIXER — MIXER ASSEMBLY
BODY ASSY.
70
2
58
72 72
82
82
10
61
62
73
73 24
59
60
68
37
64
9
5
1
76
73
73
55
70
70
76
76
76
50
70
80
57
23
11
70
116 118
117
119
116
120
7
116
117
119
116
120
118
114
115
30
31
6
16
16
17
15
85
72
4
113
111
109
112
18
13
41
17
12
13
71
38
39 14
41
20 19
21
35
42
36
22
78
110
29
79
27
26
25
74
43
46
8
121
32
3

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 17
CX22 DUO HAND MIXER — MIXER ASSEMBLY
BODY ASSY.
NO PART NO PART NAME QTY.REMARKS
1 CM20530 MOTOR HOUSING TOP 1
2 CM20531 MOTOR HOUSING BOTTOM 1
3 CM20654 GEAR HOUSING ASSY 1
4 CM20655 PLATE ASSY 1
5 CM20524 BAFFLE PLATE 1
6 CM20525 RECTIFIER 1
7 CM20656 SPINDLE, RIGHT 1
8 CM20522 COVER 1
9 CM20559 ARMATURE 230V .............................................. 1 ......... CX22DUOE ONLY
9 CM20591 ARMATURE 110V ............................................... 1 ......... CX22DUO ONLY
10 CM20556 FIELD COIL 110 - 230V 1
11 CM20657 SPINDLE, LEFT 1
12 CM20658 MIDDLE SHAFT 1
13 CM20518 WASHER 3
14 CM20504 MIDDLE SHAFT 1
15 CM20546 GEAR ASSY 1
16 CM20501 GEAR 2
17 CM20506 SLEEVE 2
18 CM28543 GUIDE 1
19 CM20659 FORK 1
20 CM20660 SLIDING PLUG 1
21 CM20508 SPRING FOR GEAR SHIFTER 2
22 CM20513 WASHER 2
23 CM20540 FRAME PROTECTION RIGHT 1
24 CM20541 FRAME PROTECTION LEFT 1
25 CM20528 GEAR KNOB 1
26 CM20562 KNOB ASSY 1
27 CM20581 SEALING 1
29 CM25022 SLEEVE 1
30 CM29523 RUBBER SLEEVE 1
31 CM29522 BALL BEARING 607 2Z 1
32 CM25055 BALL BEARING 6000 2RS 1
35 CM23507 BALL BEARING 6002 2RS 2
36 CM23016 BALL BEARING 6204 2RS 2
37 CM20509 SPRING FOR BRUSH ASSY 2
38 CM20661 COVER 1
39 CM20609 SCREW 4X12 2

PAGE 18 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)
CX22 DUO HAND MIXER — MIXER ASSEMBLY
BODY ASSY.
70
2
58
72 72
82
82
10
61
62
73
73 24
59
60
68
37
64
9
5
1
76
73
73
55
70
70
76
76
76
50
70
80
57
23
11
70
116 118
117
119
116
120
7
116
117
119
116
120
118
114
115
30
31
6
16
16
17
15
85
72
4
113
111
109
112
18
13
41
17
12
13
71
38
39 14
41
20 19
21
35
42
36
22
78
110
29
79
27
26
25
74
43
46
8
121
32
3

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 19
CX22 DUO HAND MIXER — MIXER ASSEMBLY
BODY ASSY.
NO PART NO PART NAME QTY.REMARKS
41 CM24060 CIRCLIP A15 X1.5 2
42 CM20571 CIRCLIP 20 2
43 CM20572 CIRCLIP 47 2
46 CM28548 PIN 5X5X10 2
50 CM20565 SWITCH ASSY 230V .......................................... 1 .......... CX22DUOE ONLY
50 CM20593 SWITCH ASSY 110V .......................................... 1 .......... CX22DUO ONLY
55 CM29534 CAPACITOR
57 CM23557 CORD, ELECTRIC, 230 V WITH EU PLUG ......... 1 .......... CX22DUOE ONLY
57 CM27030 CORD, ELECTRIC, 230 V WITH CH PLUG ........ 1 .......... CX22DUOE ONLY
57 CM27053 CORD, ELECTRIC, 230 V WITH UK PLUG ........ 1 .......... CX22DUOE ONLY
57 CM27035 CORD, ELECTRIC, 110 V WITH UK PLUG ......... 1 .......... CX22DUO ONLY
57 CM27054 CORD, ELECTRIC, 110 V WITH USA PLUG ...... 1 .......... CX22DUO ONLY
58 CM20588 CABLE SWITCH 1
59 CM23556 CORD GUARD 1
60 CM20584 WIRE RED 1
61 CM20583 WIRE BLUE 1
62 CM20584 WIRE RED 1
64 CM20579 TERMINAL BLOCK 1
68 CM20567 BRUSH SET 1
70 CM25062 SCREW 4 X 15 14
71 CM20636 SCREW 4X55/20 2
72 CM20574 SCREW 4X70/30 4
73 CM20575 SCREW M6X20 8
74 CM20577 SCREW 30X12 2
76 CM20576 NUT M6 8
78 CM20578 BALL 5 MM 1
79 CM20507 SPRING FOR GEAR SWITCH 1
80 CM23555 CORD CLAMP 1
82 CM27011 WASHER 2
85 CM20662 SEALING 1
109 CM29544 BALL BEARING 608 2RS 1
110 CM20663 SHAFT 1
111 CM28568 CIRCLIP 22 2
112 CM20664 GEAR 1
113 CM28569 CIRCLIP 8 1
114 CM20665 HEXAFIX®LEFT - I ............................................. 1 .......... INCLUDES ITEMS W/ #
115 CM20666 HEXAFIX®RIGHT - II ......................................... 1 .......... INCLUDES ITEMS W/ $
116#$ CM20667 RING FOR HEXAFIX®4
117#$ CM20668 SPRING FOR HEXAFIX®2
118#$ CM20669 PIN FOR HEXAFIX®4
119#$ CM20670 SLEEVE FOR HEXAFIX®2
120#$ CM20571 CIRCLIP 20 2
121 DCL1260 DECAL; STOW LOGO 1

PAGE 20 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)
CX44 DUO HAND MIXER — MIXER ASSEMBLY
BODY ASSY.
105
10
90
86
87
87
86
5
1
91
91
91
96
96
42
96
41
5
5
70
72
79
91
73
91
91
2
174
175
96
82
81
20
94
80
83
93
22
85
77
19
71
95
52
4
93
16
15
50
51
35
28
36
37
39 38
107
29
60
29
31
123
34 60
31
121 122
51
5
55
61
56
40
101
120
48
103
46
45
44
97
62
25
126 128
127
129
126
130
14
126
127
129
126
130
128
114
125
66
39
26
30
27
30
176