Strong SR-CAB-8U User manual

ASSEMBLY MANUAL
SR-CAB-8U SR-CAB-10U SR-CAB-12U SR-CAB-14U
CABINET RACK

pg.2
Cabinet Rack Assembly Manual
STRONG IN-CABINET RACKS
Strong™equipment racks are available in sizes 8U to 14U and are constructed with 13 gauge (2.5mm)
thick horizontal side rails to provide unmatched rigidity. Advanced features include: EasyGlide™
runners to easily slide in or out of a cabinet, and E-coated rack rails to maintain clean threads.
PARTS INCLUDED
A. Pre-assembled Side Frame (2)
B. Vented Connection Plate (4)
C. EasyGlide™Runners (2)
D. Field Wiring Terminal (1)
Assembly Hardware
(Not identied in diagram)
TOOLS NEEDED
• #2 Phillips Screwdriver
• 11mm Wrench (optional - for EasyGlide)
A
C
B
D
To ground cabinet, connect the ground wire
to the eld wiring terminal (D) on the bottom
side of the frame using a UL listed closed
loop connector with a minimum 12AWG wire.
Use the included #10 internal tooth washer
and 10-32 nut to tighten the connection.

Cabinet Rack Assembly Manual
pg.3
© 2015 STRONG™
ASSEMBLY STEPS
Assemble the rack on a level surface to ensure that the arms, base and top remain square.
1. Position the pre-assembled side frames on a at surface with the rack pillars facing you, and the mounting
hardware in reach.
2. Line the vented connection plate up with the side frames so that the screw holes line up.
3. Screw the 3 screws in on each side by hand. Do not tighten. Note: For grounding, include a #10 washer
between the screw and connection plate in each corner.
4. Once all the connection plates are lined up, tighten the screws.
5. Install the EasyGlide™ Runners on the racks as shown in the above diagram if the rack will not be used
with the SR-RACKSLIDE-300. Insert the screws through the bottom of the rails and fasten from the top
using the included nuts and an 11mm wrench.
CAUTION: This rack is intended for use only with Strong™shelf models with a maximum
combined load of 250 pounds. Use with heavier than the maximum load indicated may
result in instability causing possible injury.
UL Listing covers the equipment rack only.
ACCESSORY INSTALLATION
1. Determine the desired layout of the components, their space requirements, and where the vents and blanks
will need to be placed.
2. Starting with the shelf at the bottom of the rack, unpack shelf, keeping in mind the heaviest components
should be placed at the bottom of the rack.
3. Unfold shelf side panels and mount shelf in desired rack location using four Strong™ rack screws. Note:
accessory mounting screws are not included with shelves, vents or blanks (only with racks).
4. Install component(s) onto shelf.
5. Repeat steps 2-4 for the remaining shelves.
A vent should be placed above components that generate excessive heat, such as surround receivers,
ampliers, satellite receivers, DVRs, cable boxes and media servers.
OPTIONAL ACCESSORIES
• RACK SLIDE - An optional rack slide (SR-RACKSLIDE-300) is available to install with the In-Cabinet Racks in
cabinetry or wall applications, enabling the rack to be pulled out and rotated.
• CABINET TOP & BOTTOM COVERS
RACK SCREWS
Screws are not included with Strong™ rack accessories, but extra screws are available (SR-SCREWS-200JAR) for purchase.
One no-roll jar includes 200 black 10-32 screws featuring #2 Phillips heads and captive nylon washers.

© 2015 STRONG™
150512-2112
All Strong™ products have a Lifetime Limited Warranty. This warranty
includes parts and labor repairs on all components found to be defective
in material or workmanship under normal conditions of use. This
warranty shall not apply to products which have been abused, modied
or disassembled. Products to be repaired under this warranty must be
returned to SnapAV or a designated service center with prior notication
and an assigned return authorization (RA) number.
LIFETIME LIMITED WARRANTY
Lifetime
For Technical Support : 1.866.838.5052