Strong VersaBox SM-RBX-PRO-14-BLK User manual

Pg. 1
www.snapav.com Support: 866.838.5052
SM-RBX-PRO-14-BLK Installation Manual
Installation Manual
Strong VersaBox™SM-RBX-PRO-14-BLK
Overview
Thank you for purchasing a great product from Strong™. We appreciate your purchase and
are committed to providing the highest quality products possible. The Strong VersaBox™ Pro
is designed to provide the best UL-Listed in-wall box solution for installers adding equipment
behind low-prole displays and other wall-mounted equipment in an area where coding is
strictly enforced. It can easily be installed in existing ceilings and walls, or in new jobs using
the optional dust cover.
Inside the enclosure, up to two layers of components may be mounted using the built-in
attachment points and the pivoting center mounting plate. Easy-to-remove cutouts allow outlet
boxes and low-voltage rings to be installed in the sides of the box to save space for more
equipment. The center support plate is perforated to aid in wire management and device
mounting and can be set to different depths to allow for more varied installations. The plate can
also be modied as needed so that larger components t into the box.
Package Contents
(1) SM-RBX-PRO-14-BLK
(1) Center Support Plate
(1) Cover Plate/Door
(1) Dust Cover
(1) RBX Pro Trim Ring/Bezel
(6) Grommets
(1) Hardware Pack
Important Instructions and Considerations for Installation
• Read and follow all instructions.
• Before beginning installation, carefully plan locations, accounting for potential electrical, ductwork, plumbing or other obstacles
that may interfere with installation of the box, equipment, or wiring.
• Contact a suitable contractor if you are unsure of how to best install.
Recommended for Installation
Tools
• #1 Phillips Screwdriver
• Drywall Saw
• Tape Measure
• Level
• ¼” Flat Head Screwdriver (optional)
• Electric Drill and ¼” bit (optional)
• Tin Snips (optional)
Optional Accessories and Hardware
• Drywall screws
• Electrical box and low voltage ring for adding terminations to cutouts
• Compact Wattbox (sold separately)
Use only standard size cover plates on boxes and rings installed
in the Strong VersaBoxTM. Midi and jumbo size plates will not t.
This equipment must be installed and assembled by qualied service personnel in accordance with
local building codes. Total equipment weight stored in this enclosure must not exceed 15 pounds.
CAUTION:

Pg. 2
www.snapav.com Support: 866.838.5052
SM-RBX-PRO-14-BLK Installation Manual
Assembly Diagram
Note: To remove the cover with ease, swing
door open pulling from the nger openings on
the side of the cover rst.
Old Work Installation Instructions
Tighten
Screws with
#1 Phillips
Screwdriver
Cutout Dimensions
14.25" (W) x 8.5" (H)
Horizontal
Dog Ears
New Work Installation Instructions
The SM-RBX-PRO-14-BLK dust cover is designed to preserve the Strong In-Wall VersaBox in new work applications before drywall
is hung on the studs.
Note: Determine what thickness the drywall will be, before installing. If the studs are wider than 16” use dog ears once the drywall is
installed.
Note: Mounting screwholes are only
located on the le and right sides, as
illustrated.
1. Mark the desired height of the top of the SM-RBX-PRO-14-BLK on the wall
between two stud centers. Use a stud nder to locate the stud locations.
2. Use the cutout template from the box, or located on the support tab of the
product page on snapav.com to mark the wall, using a level to line it up
correctly.
3. Carefully cut the opening using a drywall saw.
4. After the hole is cut, test t the box, and clean up the opening as needed.
5. Remove the center support plate from the Strong VersaBox™ Pro. The
platform standoffs may be left in place.
6. Insert the box into the opening. Using a #1 Phillips screwdriver, secure
the box to the drywall using the dog legs on each side of the enclosure as
illustrated.
7. Install the trim/bezel with 8 screws on the inside edge for a nished look.
Note: If any of the 4 dog legs will not extend correctly due to stud
clearance beside the box, a screw may be inserted through the side
of the box into the stud if one is close enough. Refer to the New
Work Installation section later in the manual for reference of where
to insert the screw/s.
Strong VersaBox™ Pro Installation (before drywall is installed)
1. Remove the center support plate from the VersaBox Pro. The platfom
standoffs may be left installed.
2. Open any knockouts in the VersaBox Pro that will be used for wiring or
electrical.
3. Pull the wires out of the wall opening and pull them into the desired openings
of the VersaBox.
4. Attach the VersaBox Pro to the studs with the 4 included lag bolts and protect
the inside of the VersaBox Pro from the drywall install by inserting the dust
cover.
5. Once drywall is installed, remove the dust cover, attach the trim/bezel, and
install equipment.
Go to the SM-RBX-PRO-14-BLK product page at www.SnapAV.com for tips
and instructions to install equipment into the VersaBox Pro.

Pg. 3
www.snapav.com Support: 866.838.5052
SM-RBX-PRO-14-BLK Installation Manual
Perforations for wire
management or
attaching equipment
Compact Wattbox
Place Holder/Knockout
Using the Center Support Plate
Changing the Center Support Plate Position
Changing the Standoff Position
The center support allows for almost any mounting conguration
possible. Additional sections may be trimmed out using a pair of tin snips
for further utilization of mounted equipment.
1. Insert ¼” at head screwdriver into the slot at the rear of the standoff
and twist. Pry upward to remove it. (A)
2. Rotate the standoff 180°. (B)
3. Press the standoff back in with the screwdriver until it clicks into
place. (C)
4. Repeat for each of the standoffs.
Using Knockouts
The knockouts on the top and bottom of the VersaBox Pro may be used
for installing low voltage rings or for outlet boxes. If an outlet box is
installed, it must be an old work, residential grade box with integrated
work supports to allow for secure mounting.
Note: Once installed, to ensure re safety, the silicone grommets must
remain in the VersaBox.
• When using these as wire guides, slit each grommet down the
middle in a “+” shape, never remove them.
• When using these for conduit, cut the grommet for the exact size
and shape of the conduit so that it gives the conduit a tight seal.
Modules
The back wall of the VersaBox Pro has holes and knockouts stamped
into it on 6” centers to allow for easy structured can module installation.
Use a ¼” drill bit to open more of the knockout stamps as needed to
mount equipment.
Installing Equipment into the Strong VersaBox™ Pro
The center support plate allows for a variety of equipment conguration options. To accommodate equipment of different thicknesses,
the plate hinges can be reversed. The plate is also perforated so that it can be trimmed down in size, or used for securing modules
and wiring.
Experiment with the equipment configuration to determine the best installation method. For images of different configurations
of equipment installed in the VersaBox Pro, see the VersaBox Pro product page and Support Tab at www.SnapAV.com.
You have the option to orientate the standoffs toward the front or rear
of the VersaBox Pro. These 2 different positions provide the platforms
with 4 different levels (1A, 1B, 2A, 2B), as illustrated. The strandoffs and
positioning of the Mounting Platforms effectively give you the option to
raise or lower the platforms to the desired height, up to being ush with
the front of the can.
1A
2A
1B
2B
Recessed
Front
Recessed
Rear
Raised
Front
Raised
Rear
1A
2A
1B
2B
A
C
B

Pg. 4
www.snapav.com Support: 866.838.5052
SM-RBX-PRO-14-BLK Installation Manual
Dimensions
Warranty
Limited Lifetime Warranty
All Strong back-boxes and brackets have a Lifetime Limited Warranty. This warranty includes parts and labor repairs on all
components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to
products that have been abused, modied, or disassembled. Products to be repaired under this warranty must be returned to
SnapAV or a designated service center with prior notication and an assigned return authorization number (RA).
Lifetime
Contacting Technical Support
Phone: [phone] Email: [e-mail]
© 2014 Strong™
140905-1500
15.51”
14.55”
3.76”
13.29”
14.25”
Double Layer
(Factory Position)
Single Layer
1.50in.
2.00in.
2.10in.
1.40i
n.
Center Support Plate Position Dimensions
Insert
hooks
on one
side rst
Push in on
opposite
side to
close
Installing the Optional Compact WB-200VB
Remove the bottom panel by unscrewing the 4 pre-installed screws. Insert the
compact wattbox, and re-thread the four screws to permanently secure it. For
further installation information, see the WB-200VB manual.
Attaching the Strong VersaBox™ Pro Cover
To attach the cover, knock out any additional wire pass-throughs needed, and
then slid the cover on, seating the hooks on the right side rst, and pushing the
left side in until a “click” is heard.