Strong Strong Razor Series User manual

INSTALLATION MANUAL
SM-RR-F-L / SM-RR-T-L
Strong™ Razor Series Universal Fixed and Tilt Mount
for Large Displays
SM-RR-T-LSM-RR-F-L

2
Installation Manual
© 2020 Strong
WARNINGS:
• These wall mounts are intended for use only with the maximum weight capacities listed below.
• Installation by a qualied professional is highly recommended for this product.
• Do not begin installation until you thoroughly read and understand these instructions.
• Ensure the mounting wall will safely support four times the combined weight of the mount and display panel.
• The manufacturer does not accept responsibility for incorrect installation.
CAUTION:
Use with heaver than the maximum weight indicated may result in instability which could possibly cause injury.
AVERTISSEMENTS:
• Ces supports muraux sont pour être utilisés seulement avec les capacités de poids maximales ci-dessous.
• L'installation par un professionnel qualié est fortement recommandée pour ce produit.
• Ne commencez pas l'installation avant d'avoir lu et compris ces instructions.
• Assurez-vous que le mur de montage supporte en toute sécurité quatre fois le poids total du support et du panneau
d'a󰀩chage.
• Le fabricant n'accepte aucune responsabilité pour une installation incorrecte.
MISE EN GARDE:
une utilisation avec un poids plus haut que le poids maximal indiqué peut provoquer une instabilité et ainsi des
blessures.
Specications Tools Required Box Contents
• Maximum Weight • Power Drill • Wall Plate (1)
• Tilt: SM-RR-T-L: 100lbs • 5/16" and 3/32" Drill bit • Arm Left (1)
• Fixed: SM-RR-F-L: 100lbs • Phillips Head Screw Driver • Arm Right (1)
• Tilt Range • Level • Hardware Kit
• Tilt: SM-RR-T-L: 0° / +11° • Socket Wrench with 1/2 Socket head
• Fixed: SM-RR-F-L: -7° / +0°
• Post Install Adjustment: 3.48"
Fixed & Tilt
Horizontal Measurement (mm)
50 75 100 200 300 400 500 600 700 800
Vertical Mesasurement
(mm)
50 M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL L, XL L, XL XL XL
75 M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL L, XL L, XL XL XL
100 M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL L, XL L, XL XL XL
200 M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL L, XL L, XL XL XL
300 M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL L, XL L, XL XL XL
400 L, XL L, XL L, XL L, XL L, XL L, XL L, XL L, XL XL XL
500 XL XL XL XL XL XL XL XL XL XL
600 XL XL XL XL XL XL XL XL XL XL
HARDWARE KIT
IMAGE DESCRIPTION ITEM QUANTITY
Lag Bolt (A) 8 × 63 mm 5
Lag Washer (B) 8.4 × 16 × 2 mm 5
Concrete Anchor (C) 10 × 50 mm 5
Screw (D) M6 × 20 mm 4
Screw (E) M6 × 40 mm 4
Screw (F) M8 × 20 mm 4
Screw (G) M8 × 40 mm 4

Installation Manual
3
www.snapav.com Support: 866.838.5052
Figure 2
Drill holes and
insert anchors.
Place wall arm
assembly plate
over anchor and
secure with
lag bolt.
Tighten all
lag bolts.
Wall Arm
Concrete
Wall
Lag Bolt
Figure 1
Holes
Center of
Studs
Wall Plate Center hang hole
for easy wall
plate installation
INSTALLATION:
Step 1: Mount the Wall Bracket Assembly
For Mounting on a Wood-Stud Wall
1. Pre-drill holes into two wood studs using a 3/32" drill bit.
Be sure to drill into the center of the studs at least 2-1/2"
deep. The use of a stud nder is highly recommended.
2. Insert four Lag Bolts (A) and Washer (B) into holes
through the Wall Plate and tighten down (Figure 1).
WARNING: Studs must be a minimum of 2"×4" and covered
with no more than 3/8" thick drywall.
WARNING: Tighten bolts so that wall plate is rmly attached,
but do not overtighten. Overtightening can damage the bolts,
greatly reducing their holding strength.
For Mounting on a Concrete Wall
3. Pre-drill holes into concrete using 5/16" drill bits to a
depth of 2 -1/2". Insert concrete wall anchors (C) and tap
in with hammer, if necessary (Figure 2).
4. Insert four Lag Bolts (A) and Washers (B) into holes
through the Wall Plate and tighten (Figure 1).
WARNING:WARNING: When installing wall arm assembly on cinderWhen installing wall arm assembly on cinder
block, verify rst that you have a minimum of 1-3/8" of concrete block, verify rst that you have a minimum of 1-3/8" of concrete
thickness to be used for the concrete anchors.thickness to be used for the concrete anchors. Do not drill intoDo not drill into
mortar joints!mortar joints! Be sure to mount in a solid part of the block,Be sure to mount in a solid part of the block,
generally 1" minimum from the side of the block. Cinder blockgenerally 1" minimum from the side of the block. Cinder block
must meet ASTM C-90 specications. It is suggested that a must meet ASTM C-90 specications. It is suggested that a
standard electric drill on slow setting is used to drill the holestandard electric drill on slow setting is used to drill the hole
instead of a hammer drill to avoid breaking out the back of theinstead of a hammer drill to avoid breaking out the back of the
hole when entering a void or cavity.hole when entering a void or cavity.
CONCRETECONCRETE must be 2500 psi density minimum. Lighter must be 2500 psi density minimum. Lighter
density concrete may not hold concrete anchor. density concrete may not hold concrete anchor. Make sureMake sure
that the supporting surface will safely support the combined loadthat the supporting surface will safely support the combined load
of the equipment and all attached hardware and components.of the equipment and all attached hardware and components.
5. Insert four Lag Bolts (A) into the wall anchors (C) through
the Wall Plate. Tighten all bolts.
WARNING:WARNING: Tighten bolts so that wall plate is rmly attached, Tighten bolts so that wall plate is rmly attached,
but do not overtighten. Overtightening can damage the bolts,but do not overtighten. Overtightening can damage the bolts,
greatly reducing their holding strength.greatly reducing their holding strength.
IMAGE DESCRIPTION ITEM QUANTITY
Screw (H) M8 × 50 mm 4
Spacer (I) 8.5 × 5 mm 4
Spacer (J) 8.5 × 10 mm 4
Spacer (K) 8.5 × 19 mm 4
Spacer (L) 8.5 × 22 mm 4
M6 Washer (M) 6.4 × 18 × 2 mm 8
M8 Washer (N) 8.4 × 20 × 2 mm 8
Hex Wrench (O) M3 × 260 mm 1

© 2020 STRONG™
200706-1115
Step 2: Mount Arms to TV
1. Determine the diameter of the screw (parts D through H) your
TV requires by carefully trying to hand-thread one into the
threaded insert on the rear of the TV. If there is any resistance,
stop immediately.
2. Thread the screw through the washer (M or N), arm, spacer
(parts I through L), and into the TV.
NOTE:NOTE: Spacers are commonly needed on TVs with curved backs orSpacers are commonly needed on TVs with curved backs or
recessed screw inserts.recessed screw inserts.
3. Ensure the arms are installed at side to TV and are square to
each other after all screws have been installed (Figure 3).
Step 3: Hang TV on to the Wall Plate
Carefully lift the TV to hook the arms over the top lip of the wall
plate (Figure 4). The bottom of the arms will then rest on the top
edge of the locking mechanism. The locking mechanism can be
released by pulling the pull strings down and allowing the TV to
slide into place. Once you release the pull strings the TV will be
locked. Do not release the TV until it is completely connected to the
wall plate.
NOTE:NOTE: It is easier to hang the TV if the tilt feature is rst expanded so It is easier to hang the TV if the tilt feature is rst expanded so
that the hook is extended away from the back of the TV and bracket.that the hook is extended away from the back of the TV and bracket.
Adjustments:
Tilt Adjustment
Turn Tilt Adjustment Bolt (Figure 5) clockwise to tighten grip;
counter-clockwise to loosen grip.
Post-Install Level Adjustment
If display is not horizontally level when mounted, adjustment
screws are included at the top of each arm for micro-adjustments
(Figure 6). Use the provided hex wrench (O) to raise or lower the
screw and adjust the mount accordingly.
Up and Out Adjustment (Fixed Only)
Fixed mounts include an Up and Out feature for easy access to portsFixed mounts include an Up and Out feature for easy access to ports
on the sides and back of displays. To get the most adjustment out ofon the sides and back of displays. To get the most adjustment out of
this feature be sure to pull the display toward you and directly awaythis feature be sure to pull the display toward you and directly away
from the wall (Figure 7).from the wall (Figure 7).
NOTE:NOTE: Take caution to avoid slips or drops.Take caution to avoid slips or drops.
Lifetime Limited Warranty
Strong™ Mounts have a Lifetime Limited Warranty. This warranty includes parts andStrong™ Mounts have a Lifetime Limited Warranty. This warranty includes parts and
labor repairs on all components found to be defective in material or workmanshiplabor repairs on all components found to be defective in material or workmanship
under normal conditions of use. This warranty shall not apply to products which haveunder normal conditions of use. This warranty shall not apply to products which have
been abused, modied or disassembled. Products to be repaired under this warranty been abused, modied or disassembled. Products to be repaired under this warranty
must be returned to SnapAV or a designated service center with prior notication and must be returned to SnapAV or a designated service center with prior notication and
an assigned return authorization (RA) number.an assigned return authorization (RA) number.
For Technical Support call 1.866.838.5052
Adjustment
Screw
Locking
Tab
OR
Pull out and
away from
the wall
Figure 4
Figure 6
Figure 7
Figure 3
Tilt Adjustment Bolt
(Use Provided Hex Wrench)
Fixed Mount Tilt Mount
Figure 5
TV Side
TV Side
Wall Bracket
Mount Arms
Mount Arm