Studer Xtender-WeCo 5k3 User manual
Quick Installation Guide
Studer Xtender-WeCo batteries
READ THE MANUAL BEFORE INSTALLING THE BATTERY
www.wecobatteries.com
WeCo
Configuring Studer + Weco
This document describes the configuration of Studer’s devices from the xtender range when
used with Weco batteries.
The xtender range is compatible with following Weco batteries using the xcom CAN through
communication with the BMS.
Studer xtender range
Weco batteries
xtender
xts 1400-48, xtm 2600-48, xtm 4000-48
xth 6000-48, xth 8000-48
variotrack + variostring
vt 40, vt 65, vt 80, vs 70, vs 120
5k3, 4k4 Pro, 4k4
Minimum configuration list
Studer device*
Cont. Power / Peak
Power 5sec (VA)
Minimum amount of WECO batteries (units)
5k3
4k4 Pro
4k4
xts 1400-48
900 / 2’800
1
1
1
xtm 2600-48
2’000 / 6’500
1
1
2
xtm 4000-48
3’500 / 10’500
1
2
3
xth 6000-48
5’000 / 15’000
2
2
4
xth 8000-48
7’000 / 21’000
2
3
5
*variotrack and variostring do not require a minimum amount of batteries
www.wecobatteries.com
WeCo
Configurations
Remove the back cover of the
Xcom-CAN by loosening the
two screws on the back side
Change the DIP switch settings match
the picture and the image below
Jumper position as per below scheme
(3 are used on a total of 4 jumpers kit)
WeCo www.wecobatteries.com
ON DIP
1
ON
4
OFF
2
ON
3
ON
5
OFF
6
ON
7
OFF
8
ON
Cabling Overview
Overall Connection
Remove the plastic Cover from the bottom side of the Xtender Inverter and remove
the front cover of the RCC-02 (1 screw)
Remove the back cover of the Xcom-CAN (2 back screws)
A- CAN Port 1 of the Inverter (Connects to RCC-02 Port-1)
B- CAN Port 2 of the Inverter (Connects to Xcom COM Port-1)
C- CAN Port 1 of Xcom-CAN Connects to the battery CAN RJ45
WeCo www.wecobatteries.com
AA
BB
C
Cabling of the devices
Xtender Bottom Side
A- CAN Port 1 of the Inverter RJ45 Port
B- CAN Port 2 of the inverter RJ45 Port
T O
OT
Xcom-CAN COM Bus Side
B- CAN Port 2 of the inverter to RG45 COM
Port 1 of Xcom
COM Port 2 of Xcom remains empty
LED GREEN
●Make sure the LED blinks 2 times- interval and repeats.
●If the LED blinks Green + RED check the connection
again because the communication is not correct.
●If the LED is RED the connection is wrong.
WeCo www.wecobatteries.com
A B
B
Termination Switch to the
right of the two RJ45 Ports
Termination Switch to the
right of the two RJ45 Ports
Set Switch to the right.
Set Switch to the left.
Cabling of the devices
Overall Connection
A- CAN Port 1 of the Inverter RJ45 Port
B- CAN Port 2 of the inverter RG45 Port
T O
A- COM Port 1 of the RCC-02
*RCC-02 COM Port 2 is not used
B- COM Port 1 of the Xcom (ComBus Side)
C- CAN Port 1 of the Xcom (CAN Side)
Connected to battery CAN RJ45
OT
All termination switches are
set to the left
www.wecobatteries.comWeCo
A B
A B
Termination Switch to the
right of the two RJ45 Ports
C
Communications Common Error
If the DIP switch are in the wrong position the RCC-02 display
Will show only limited battery information or N.A.
Once the communication is correct try to disconnect the CAN cable from the battery to
the X-Com, must show a RED BACKGROUND
Reconnect the CAN cable and the RCC-02 Display must show the info 226
(communication restored, see pic. above)
WeCo www.wecobatteries.com
BATTERY OVERVIEW
Keep the battery OFF Press the ON/OFF button for 10 seconds and make
sure that all the LED are OFF and measure the terminal output with a Volt
meter.
No LED lights should be visible in when the battery is in OFF MODE status
Make sure the output is ZERO Volts with a Voltmeter
before operating on the battery terminal block
WeCo www.wecobatteries.com
Cabling of the devices
4K4 PRO BATTERY BOTTOM SIDE CONNECTION
From the original position of the DIP switch,
move it as shown in the picture, 5th PIN enable the CAN In-Out comm
Attention: any action on the DIP Switch must be followed by a reset of the
battery with a long press of the ON/OFF button
www.weco.uk.com
WeCo
CAN /BMS PORT
ON DIP
1
OFF
2
OFF
4
OFF
5
ON
3
OFF
This manual suits for next models
2
Table of contents
