AQUATECH Sync Transmitter Housing User manual

Instruction manual
Sync Transmitter Housing
Compatible with entire range of Sport Housings

Thank you for purchasing this AquaTech SYNC
Transmitter Housing.
Overview:
The SYNC Transmitter Housing is a compact and easy to
use housing that supports a range of flash transmitters.
Wirelessly connect your camera to one or multiple
professional strobes, or even speedlights to create a
range of lighting eects that capture your unique vision.
The simple design of the SYNC connects to your water
housing via our 6 Pin SYNC cable system and has the
ability to support TTL modes and Hi-Speed SYNC (for
Canon and Nikon only). 6 Pin SYNC cables are available
in a range of sizes up to 30ft, so you can float your
SYNC to the surface to continue to transmit the radio
signal even if you’re well below the surface.
An amazing feature of the SYNC Transmitter Housing
is the option to have the SYNC wirelessly control the
LUX Flash Housing when using a Godox transmitter.
This opens up a world of new options for wireless o-
camera flash in the water with full TTL and HSS (for
Canon and Nikon only).
The SYNC is easily secured with 2 thumbscrews to
provide an even seal across the clear backplate. As
the SYNC is able to support multiple brands with it’s
control-free design, the exposure control for your lights
can either be performed in camera or on the light itself.
The SYNC features a new quick-cam mount that
connects to the supplied Pro Mount V3 without the
need for any additional tools. Easily interchange your
SYNC Transmitter Housing with an action camera on
the Pro Mount V3 when lighting is not required.
Please read the following instructions and care tips be-
fore using your SYNC Transmitter Housing for the first
time. You can also visit our website and YouTube chan-
nel for more tips and information.
What’s in the box
• SYNC Transmitter Housing (please choose the
compatible camera manufacturer option)
• Pro Mount V3
• 13” 6 Pin Flash SYNC Lead
• Camera Hotshoe Connector
• AquaTech Flash Bulkhead Connector
Table of Contents
• Whats in the box
• Nomenclature
• Initial setup
• Using the SYNC Transmitter Housing underwater
• Safety information
• Maintenance and repair
• Limit of liability
• Warranty
• Servicing
• Returns
• Legals
1

Nomenclature
2
Quick Cam Mount
Polyurethane body
Turn Knob

Initial Setup
• Additional Tools Needed: Flathead screwdriver,
Crescent wrench
• Open SYNC Transmitter Housing
• Then simply slide your transmitter into SYNC Hot
Shoe
• Turn transmitter on, and lineup SYNC backplate
holes with SYNC housing
• Insert Turn Knob from front of SYNC and thread it in,
spinning Turn Knob clockwise.
• Remove the Flash Bulkhead plug from your Sport
Housing with a Flathead screwdriver turning counter
clockwise, install the supplied Flash Bulkhead onto
your Sport Housing making sure the two o-rings
are properly in place. Note: the additional Flash
Bulkhead will be found bagged with your grease,
hex key, Flash Sync Cable and camera hot shoe.
• **Once the Flash Bulkhead is installed onto your
Sport Housing, attach the female end of the Camera
Hotshoe into male end of the Flash Bulkhead.
• Once the Flash Bulkhead is installed attach the
female end of Camera Hotshoe into male end of
recently installed Flash Bulkhead.
• Slide Camera Hotshoe into camera body.
• Unscrew cap from SYNC housing Bulkhead and
housing Flash Bulkhead.
• Remove caps from both ends of the SYNC cord.
• Install one end of the SYNC cord into SYNC Housing
Bulkhead. Ensure it is correctly lined up by aligning
electrical pins.
• Place the attached Sync cord Male threaded fastener
over the Female threaded Bulkhead and screw in
clockwise until secure.
• Attach the other end of SYNC cord into housing
Bulkhead following the previous steps.
• To install SYNC Flash Housing you will need to
have the Pro Mount installed. Please refer to the
corresponding manual for Pro Mount installation.
• Push Quick Cam Mount through the slot on the Pro
Mount and securely screw into place.
• Using the SYNC Transmitter Housing in and around
water
Using the SYNC Transmitter Housing underwater
For best results please make sure you have carefully
followed all initial setup instructions prior to taking your
SYNC Transmitter Housing underwater.
**After installing the provided additional Flash Bulkhead
onto your Sport Housing, please make certain it is
installed correctly by doing a “dunk” test (without your
camera installed). If there is any moisture or water
present after the “dunk” test is performed, please
contact AquaTech via [e-mail] so we can
assist you with the reinstall of the Sport Housing Flash
Bulkhead. Note: when not using your Sync Transmitter
Housing, the supplied Flash Bulkhead cap must be
replaced. This Bulkhead is a “dry connector’ and must
never be exposed to water. Either the sync cable or the
3

cap must be on the Bulkhead at all times. This is very
important to recap the Bulkhead on your Sport Housing
if a Sync cable is not installed.
Safety information and warning
• Do not exceed depths of 10m/33ft.
• Do not leave your Sport Housing gear in
temperatures greater than 50 C (125 F)
Maintenance and repair
With proper care your gear will last for many years. If
in time you do notice any problems that come up or if
there is any damage to the equipment please contact
AquaTech directly at servic[email protected] for repairs
or servicing.
Limit of liability
In the event of a product warranty claim, AquaTech is
only liable up to the value originally paid for the product.
Losses of associated equipment, income or any other
financial costs are not covered under this warranty, under
any circumstances.
Warranty - 1 year product warranty
We make every eort to ensure that our products
are made from the highest quality materials and
workmanship. Should you not be completely satisfied
with one of our products, we encourage you to contact
us so that we can promptly resolve any problem you
may be experiencing. Our company representatives will
deal with your issue quickly and decisively.
4
As many AquaTech products are often used in extreme
and volatile environments, we are unable to cover
for loss or damage of equipment, personal injury or
financial loss.
To reduce the risk of these losses occurring, we strongly
recommend you read the relevant product instructions
carefully and test the product before use.
What does the warranty cover?
This warranty covers any defects in materials or
workmanship, with exceptions stated below
What is not covered?
The warranty does not cover damage as the result
of normal wear and tear. Determination of what
constitutes normal wear and tear will be at the
discretion of AquaTech service centers. The warranty
guarantee only applies to the original purchaser of
the product when purchased from AquaTech direct or
through one of our authorized dealers. Therefore, we
may ask for proof of purchase. This warranty does not
cover for any loss of associated equipment such as
cameras, lenses or other associated equipment not sold
by AquaTech.
Loss of income, reputation or other financial expenses,
such as personal injury are also not covered by this
warranty. Shipping costs for returned products are the
responsibility of the customer.
How long does the coverage last?
This warranty runs for 1 year from the date your product
is received.