SUMMIT LOCKERS HDPE User manual

Installation Instruction
Make sure all walls and/or floors are plumb
and level.
Place lockers in desired installation space.
Finish drilling the pilot holes already in the
lockers (Fig. 2).
Loosely secure the sex bolts (P/N: 8900,
8901 as shown in Figure 6.).
Insert the divider strip (P/N:8902) between
the lockers and between the front and rear
sex bolts. (Figures 1 & 5) Cut to size if
needed.
Tighten the sex bolts with driver. (Figure 3).
Secure the lockers to the wall and/or floor.
HDPE LOCKER INSTALLATION MANUAL
803-403-8816 | WWW.SUMMITLOCKERS.COM | [e-mail]
SUMMIT LOCKERS, INC. - 138 MCLEOD ROAD, COLUMBIA, SC 29203

HDPE LOCKER INSTALLATION MANUAL
803-403-8816 | WWW.SUMMITLOCKERS.COM | [e-mail]
SUMMIT LOCKERS, INC. - 138 MCLEOD ROAD, COLUMBIA, SC 29203
Continuous Base Instructions
Assemble bases with “L”
brackets per non-welded
corners. The longer part of the
base should cover the end of the
shorter part.
Line up bases so they are square
and flush with the back of the
lockers.
3 1/4” in from the front of the
lockers, drill a pilot hole straight
down.
Screw the locker to the base
with hardware provided.

HDPE LOCKER INSTALLATION MANUAL
803-403-8816 | WWW.SUMMITLOCKERS.COM | [e-mail]
SUMMIT LOCKERS, INC. - 138 MCLEOD ROAD, COLUMBIA, SC 29203
End Panel Instructions
Drill through the pilot holes in
locker.
Line up End Panel – (note:
end panel goes to the bottom
of the locker, see picture).
Drill pilot holes in end panel,
¾” total depth.
Secure End Panel to locker
with provided hardware.(P/N:
8905).

Continuous Slope Hood Instructions
Start with slope top corners if provided, there
will be a left and right hand slope top corner,
install the left hand side first, then the right,
adjust as needed to align, install rest of slope top.
Place slope top panel flat against mounting
surface, small section down on top of lockers.
Secure small section to wall with hardware
provided (P/N: 8904)
Fold top portion down to meet lockers.
Drill a ¼” hole 2” in from the front through top of
the locker, drill a pilot hole 1 3/8” depth into
slope top.
Secure provided hardware (P/N: 8904)
HDPE LOCKER INSTALLATION MANUAL
803-403-8816 | WWW.SUMMITLOCKERS.COM | [e-mail]
SUMMIT LOCKERS, INC. - 138 MCLEOD ROAD, COLUMBIA, SC 29203

HDPE LOCKER INSTALLATION MANUAL
803-403-8816 | WWW.SUMMITLOCKERS.COM | [e-mail]
SUMMIT LOCKERS, INC. - 138 MCLEOD ROAD, COLUMBIA, SC 29203
Flat Top Corner Instructions
Fold Flaps up on flat top corner
Drill out pilot holes in locker with
¼” drill bit.
Drill out pilot holes in Flat top
corner with 1/8” drill bit.
Position in corner of lockers where
desired.
Secure from inside locker with
provided hardware (P/N: 8905).

HDPE LOCKER INSTALLATION MANUAL
803-403-8816 | WWW.SUMMITLOCKERS.COM | [e-mail]
SUMMIT LOCKERS, INC. - 138 MCLEOD ROAD, COLUMBIA, SC 29203
Continuous Flat Top Installation
Instructions
Align flat top on top of installed
lockers to desired location.
Drill ¼” holes through the top of the
locker – 6 per flat top panel.
Drill Pilot holes through ¼” holes
and into flat top, ¾” total depth.
Secure with hardware provided.
(P/N : 8905)

Filler Install Instructions
Drill through the pilot holes that are pre-drilled in the filler panel. Use
1/8” drill bit.
Drill through the pilot holes in the locker where the filler is to be
installed. Use ¼” drill bit.
Line up the holes on the filler with the locker.
Adjust and trim as needed.
From the inside of the locker, screw the provided hardware (P/N:
8905) into the filler panel.
HDPE LOCKER INSTALLATION MANUAL
803-403-8816 | WWW.SUMMITLOCKERS.COM | [e-mail]
SUMMIT LOCKERS, INC. - 138 MCLEOD ROAD, COLUMBIA, SC 29203