Summit FFBF235PL User manual

TWO-DOOR REFRIGERATOR WITH
BOTTOM FREEZER
Model: FFBF235PL
User Manual
BEFORE USE, PLEASE READ AND FOLLOW ALL THE SAFETY RULES AND OPERATING INSTRUCTIONS.
Felix Storch, Inc.
An ISO 9001:2015 registered company
770 Garrison Ave
Bronx, New York 10474
www.summitappliance.com
Write Model and Serial Numbers here:
Model No.:
Serial No.:
1

2
Contents
Safety and warning information
For your safety and correct usage, read this user manual carefully before installing
and using the appliance, including its hints and warnings. To avoid unnecessary
mistakes and accidents, it is important to make sure that all persons using the
appliance are thoroughly familiar with its operation and safety features. Save these
instructions and be sure that they remain with the appliance if it is moved or sold so
that anyone using it will be properly informed of its usage and safety notices.
For safety, follow the precautions outlined in this user manual as the
manufacturer is not responsible for damages caused by not following these
instructions correctly.
Safety for children and other vulnerable people
●According to UL standard
This appliance is not intended for use by persons
(including children) with reduced physical, sensory, or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction
concerning the use of the appliance by a person responsible for their safety.
●Children should be supervised to ensure that they do not
play with the appliance.
●Keep all packaging away from children as there is a risk of suffocation.
●If you are discarding the appliance, pull the plug out of the socket, cut the
connection cable (as close to the appliance as you can), and remove the door to
prevent children playing from suffering an electric shock or from closing themselves
inside it.
●If this appliance, featuring a magnetic door seal, is to replace an older
appliance that has a spring lock (latch) on the door or lid, be sure to render the
spring lock unusable before you discard the old appliance. This will prevent a
child from becoming trapped inside it.
Safety information and warnings 2
Installing your new appliance 6
Description of the appliance 11
Control Panel 12
Helpful tips 13
Cleaning and care 14
Disposal of the appliance 15
CALIFORNIA CARB/SNAP DISCLOSURE
This product uses eco-friendly hydrocarbon refrigerant and fully complies with California CARB
regulations.
However, we are required by California Law to provide the following disclosure statement in every product
sold in California.
"This equipment is prohibited from use in California with any refrigerants on the 'List of Prohibited Substances'
for that specific end-use, in accordance with California Code of Regulations, title 17, section 95374. This
disclosure statement has been reviewed and approved by Felix Storch, Inc. and Felix Storch, Inc. attests,
under penalty of perjury, that these statements are true and accurate."
This product does not use any refrigerants on the 'List of Prohibited Substances'"

3
General safety
●WARNING —This appliance is intended to be used in household and
similar applications such as
-staff kitchen areas in shops, offices, and other working environments:
-farmhouses and hotels, motels, and other residential-type environments:
-Bed and breakfast type environments:
-Catering and similar non-retail applications.
●WARNING — Do not store explosive substances such as aerosol cans with a
flammable propellant in this appliance.
●WARNING — If the power cord is damaged, it must be replaced by the
manufacturer, its service agent, or similarly
qualified persons to avoid a hazard.
●WARNING — Keep ventilation openings, in the appliance enclosure or in the built-
in structure, clear of obstruction.
●WARNING — Do not use mechanical devices or other means to
accelerate the defrosting process, other than those recommended by the
manufacturer.
●WARNING — Do not damage the refrigerant circuit.
●WARNING — Do not use electrical appliances inside the food storage
compartments of the appliance, unless they are of the type recommended by the
manufacturer.
●WARNING — The refrigerant and insulation blowing gas are flammable. When
disposing of the appliance, do so only at an authorized waste disposal center. Do not
expose to flame.
●WARNING — When positioning the appliance, ensure the supply cord is not
trapped or damaged.
●WARNING — Do not locate multiple portable sockets-
outlets or portable power supplies at the rear of the appliance.
Replacing the lightbulbs
●WARNING — The lightbulbs must not be replaced by the user. If the
lightbulbs are damaged, contact the customer helpline at [phone] or visit
our https://www.summitappliance.com/support
Refrigerant
The refrigerant isobutane (R600a) is contained within the refrigerant circuit of the
appliance, a natural gas with a high level of environmental compatibility, which is
nevertheless flammable. During transportation and installation of the appliance, ensure
that none of the components of the refrigerant circuit get damaged.
The refrigerant (R600a) is flammable.
●WARNING — Refrigerators contain refrigerant and gases in the insulation.
Refrigerant and gases must be disposed of professionally as they may cause eye
injuries or ignition. Ensure that the tubing of the refrigerant circuit is not damaged
prior to proper disposal.

4
The symbol is a warning and indicates the refrigerant and insulation-
blowing gas are flammable. WARNING: Risk of fire / flammable materials
If the refrigerant circuit should be damaged:
-Avoid opening flames and sources of ignition.
-Thoroughly ventilate the room in which the appliance is situated.
It is dangerous to alter the specifications or modify this product in any way.
Any damage to the cord may cause a short circuit, fire, and/or electric shock.
Electrical safety
1. The power cord must not be lengthened.
2. Make sure that the power plug is not crushed or damaged. Acrushed
or damaged power plug may overheat and cause a fire.
3. Make sure that you can access the main plug of the appliance.
4. Do not pull the main cable.
5. If the power plug socket is loose, do not insert the power plug. There is a risk of
electric shock or fire.
6. You must not operate the appliance without the interior lighting lamp cover.
7. The refrigerator is only applied with a power supply of single phase alternating current
of 115V/60Hz. If the fluctuation of voltage in the district of the user is so large that
the voltage exceeds the above scope, for safety’s sake, be sure to apply an A.C.
automatic voltage regulator of more than 350W to the refrigerator. The appliance
should be plugged into a dedicated circuit and non-GFCI or ARC fault-protected
outlet. Its plug must match the socket with the ground wire.
Daily use
●Do not store any flammable gases or liquids in the appliance, as it creates a risk of an
explosion.
●Do not operate any electrical appliances in the appliance (e.g., electric ice
cream makers, mixers, etc.).
●When unplugging always pull the plug from the electrical socket, do not pull on the cable.
●Do not place hot items near the plastic components of this appliance.
●Do not place food products directly against the air outlet on the rear wall.
●Store pre-packed frozen food in accordance with the frozen food
manufacturer’s instructions.
●The appliance manufacturer storage recommendations should be strictly adhered
to. Refer to relevant instructions for storage.
●Do not place carbonated or fizzy drinks in the freezer compartment as it creates
pressure on the container, which may cause it to explode, resulting in damage to the
appliance.
●Frozen food can cause frost burns if consumed straight from the freezer
compartment.
●Do not place the appliance in direct sunlight.
●Keep burning candles, lamps, and other items with naked flames away from the
appliance so that do not set the appliance on fire.

5
●The appliance is intended for keeping food stuff and/or beverages in a normal
household as explained in this instruction booklet. You should take care when
moving it as the appliance is heavy.
●Do not remove or touch items from the freezer compartment if your hands
are damp/wet, as this could cause skin abrasions or frost/freezer burns.
●Never use the base, drawers, doors, etc. to stand on or as supports.
●Frozen food must not be refrozen once it has been thawed out.
●Do not consume ice popsicles or ice cubes straight from the freezer as this can
cause freezer burn to the mouth and lips.
●To avoid items falling and causing injury or damage to the appliance, do not
overload the door racks or put too much food in the crisper drawers.
●This refrigerating appliance is not intended to be used as a built-in appliance.
●Keep medications away from the freezer compartment and away from the air
vents to avoid the formation of ice crystals that can damage the medications. Do
not store medications at the refrigerator door because they will be exposed to
uneven temperatures every time the refrigerator door is opened.
Caution!
Care and cleaning
●Before maintenance, switch off the appliance and disconnect the mains
plug from the mains socket.
●Do not clean the appliance with metal objects, steam cleaners, ethereal oils,
organic solvents, or abrasive cleansers.
●Do not use a sharp object instead of a plastic scraper to remove frost from
the appliance.
Installation - IMPORTANT!
●For electrical connection, carefully follow the instructions in this manual. Unpack
the appliance and check if there are damages to it.
●Do not connect the appliance if it is damaged. Report damages immediately to
the place you bought your unit from. In this case, retain packing.
●It is advisable to wait at least four hours before connecting the appliance to allow
the oil to flow back into the compressor.
●Adequate air circulation should be around the appliance, lacking this leads to
overheating. To achieve sufficient ventilation, follow the instructions relevant to
installation.
●Wherever possible the back of the product should not be too close to a wall to avoid
touching or catching warm parts (compressor, condenser) to prevent the risk of a fire,
follow the instructions relevant to installation.
●The appliance must not be located close to radiators or other heat sources.
●Make sure that the mains plug is accessible after the installation of the
appliance.
Service
●Any electrical work required to do the servicing of the appliance should be
carried out by a qualified electrician or competent person.
●This product must be serviced by an authorized Service Center, and only
genuine spare parts must be used.

6
Installing your new appliance
Before using the appliance for the first
time, you should be informed of the
following tips.
Ventilation of appliance
To improve the efficiency of
the cooling system and save
energy, it is necessary to
maintain good ventilation around the
appliance for the dissipation of heat. For
this reason, sufficient clear space
should be available around the
refrigerator.
Suggest: It is suggested that there be
50-70mm of space from the back to
the wall, at least 100mm from its top,
at least 100mm from its side to the
wall, and a clear space up front to
allow the doors to open 115°. As
shown below:
Note:
●This appliance is intended to operate
in the climate class from 55~110°F. It
may not work properly if being left at a
temperature above or below the
indicated range for a long period.
●Install your appliance in a dry place to
avoid high moisture.
●Keep the appliance out of direct
sunlight, rain, or frost. Place the
appliance away from heat sources
such as stoves, fires, or heaters.
Leveling of appliance
●For sufficient leveling and air
circulating in the lower rear section of
the appliance, the bottom feet may need
to be adjusted. You can adjust
them manually by hand or by using a
suitable wrench.
●To allow the doors to self-close, tilt the
top backward by about 10mm.
115
717

7
Reversing the door
The side at which the door opens
can be changed, from the right side
(as supplied) to the left side, if the
installation site requires it.
WARNING: Unplug the unit from the
outlet.
TOOLS NEEDED
●Tilt the refrigerator backward to
access the base, you should rest the
appliance on soft foam packaging or
similar material to avoid damaging the
backboard of the refrigerator. To
reverse the door, follow the steps
below. Different models may
correspond to different pictures.
Models will be written in the picture. If
some parts are not shown in the
picture, ignore the relevant description.
1. Stand the refrigerator upright.
Open the upper door to take out all
door racks (to avoid the racks being
damaged) and then close the door.
2. Remove part ①, loosen part ②
from the top right side of
refrigerator.
3. Remove screws ①and hinge
②. When the refrigerator with a
display on the door, you need to
pass connector ③ through the hole
of the hinge ②. (Hold the upper
door by hand when installing).
Door racks
Not provided
8mm socket wrench Thin-blade screwdriver
Cross-shaped screwdriver
8mm wrench
①
Self-tapping screws
②
Upper hinge cover
MODEL WITHOUT DISPLAY
①
Special flange screws
②
Upper hinge
③ Electrical connector
MODEL WITH DISPLAY
① Special flange screws
② Upper hinge

8
4. Remove the upper door from the
middle hinge by carefully lifting the
door straight up. Then place the
upper door on a smooth surface with
its upper cover facing upwards.
6. If the refrigerator with a display
on the door, remove part ① from the
top left side of the upper cover and
take out part ②. Then remove part
③ and put part ④ into the top right
side of the upper cover. Refer to the
above operation, install part ③ and
part ④ on the top left side of upper
cover. Install part ①
of the top right
side of the upper cover. When the
refrigerator is without a display on
the door, skip this step.
5. With a refrigerator with an LED
display on the door, take the screw
hole cover(right) from the plastic bag
and install it onto the top right side of
the refrigerator body. Then remove
the screw hole cover (left) from the
top left side of the appliance and put
it into the plastic bag.
If the refrigerator does not have an
LED display on the door, pull out the
screw hole cover from the left side
uprightly, and place it on the right
side.
7. Loosen screw ③and take down parts
②and①, install replacement door
stopper-left ④ provided (in the plastic
bag) and part ②(stop block) to the left
side with screw ③. Keep part ① with
the appliance for future reference.
8. Loosen the screws used to affix the
middle hinge and remove the middle
hinge. Then remove the lower door.
①Corner cover(left)
②
Electrical connector(left)
③
Corner cover(right)
④Electrical connector(right)
MODEL WITH DISPLAY
Screw hole cover Screw hole cover
MODEL WITHOUT DISPLAY

9
9. Place the lower door on a smooth
surface with its panel upwards.
Loose screw ③ and take down part
② and part ①, install replacement
door stopper-left ④ provided (in the
plastic bag), and part ②(stop block)
to the left side with screw ③. Keep
part ① with the appliance for future
reference.
10. Change screw hole covers on the
middle cover plate from left to right
(as shown in the figure below).
12. Remove part ③ from the lower
hinge pin, loose out the lower hinge
pin, change it to the reverse hole
site, and then tighten into position,
then install part ③ on the lower
hinge pin.
13. Replace the items remount in
step 11, change part ①to left, and
then fix them with screws ④. Install
part ② at last.
14. Slot the lower door onto the
bottom hinge pin and hold it in
position. Turn the middle hinge 180°,
change the washer on the axis to the
lower side, adjust the middle hinge to
the appropriate position, and then
install it ensuring the lower
door is in
place.
11. Tip the refrigerator backward and
remove part②.
15. Move the upper door to an
appropriate position, and then fix
①Lower hinge part (right)
②Adjustable bottom feet part
③Adjustable bottom feet part
④Self-tapping screws
⑤Adjustable bottom feet part

10
part② by screws ①. Before fixing
part ②, pass connector ③ through
hinge ② refer to step 3. (Please hold
the upper door by hand when
installing)
17. Open the upper door, mount door
racks, and then close it.
NOTE:
If your model has handles, you must
reverse handles by following the
instructions below. Remove the upper
door and place it on a smooth surface with
its panel upwards. Lever part ① and part
④, then loose screws ②, as shown in
the picture. Change the handle ③ to
the right side, then install screws
②, part, ①and part ④ in turn.
16. Connect electrical connector ①as
shown in the picture, then fix part ②by
screw ③ refer to step 2.
①Special flange screws
②
Upper hinge
③Electrical connector
①Special flange screws
② Upper hinge
MODEL WITH DISPLAY
②upper hinge cover
③self-tapping screw