SumoSecurity IP-CAM-726-A28P Manual

2. If not already shown, grab a small pointed object and
hold the reset button (RST) on the back of the IP camera
until only the blue LED remains. Give it about 20
seconds before proceeding to the next step
3. Download and launch RXCamview from the App
Store or Play Store.
4. Click the human icon on the top left and then click
on Device List.
* For initial setup, please place the IP camera
close to the wireless router. After setup, you can
move the IP camera away. We recommend switching
your Wi-Fi network initially to 2.4GHz for initial
setup.
Setup Instructions
IP-CAM-726-A28P
When Connected Standalone Wirelessly
1. If connected standalone without a NVR, connect a
12V power adapter from the DC jack to an outlet.
Wireless IP Camera, 2.8mm Lens, H.265 (with
PoE, PIR, Floodlight, and Two-Way Audio)
Power Adapter
Reset
Button

5. Click the +icon on the top right and click CUBE from
the dropdown.
7. On the next page, click the button that says, “The
green light is ashing.” NOTE: The green light does not
need to be ashing if step 2 was followed. Only the
blue LED needs to be on (static) for the quickest setup
method.
8. The next step will setup the IP camera to connect to
your wireless network. Make sure to connect it to a
2.4GHz SSID. The IP camera will not take 5GHz
networks. When asked to join Wi-Fi network
“CARD_XXXXXXXXXXXXXXXX”, go ahead and join it. This
is the IP camera’s own internal Wi-Fi SSID. It needs to
join the its own internal Wi-FI SSID in order to save your
wireless network.
6. The camera for the phone will open up. Scan the QR
code on the back of the IP camera.
Note: The green light does not need to
be ashing for setup
z
Setup Instructions

9. Wait for the IP camera to connect to the wireless
router. Note that if the SSID or password are entered
incorrectly or if the connection is unsuccessful, you will
need to go back to step 7 to setup the device again.
10. When connected successfully, you will need to set a
password for the IP camera. We recommend setting a
password that cannot be easily guessed.
Setup Instructions
11. If everything was setup correctly, on the connection
status, it will say connected. Click the play icon to start
viewing.

Setup Instructions
When Connected Standalone Wired
1. If connected standalone without a NVR, connect a
12V power adapter from the DC jack to an outlet and
then connect an Ethernet cable from the RJ45 jack to
the LAN port on a router
Power Adapter
3. Download and launch RXCamview from the App
Store or Play Store.
4. Click the human icon on the top left and then click
on Device List.
5. Click the +icon on the top right and click IPC/N-
VR/DVR from the dropdown.
6. The camera for the phone will open up. Scan the QR
code on the back of the IP camera.
2. Alternatively, instead of connecting to a power
adapter, you can also connect it to a PoE switch via
Ethernet cable.
PoE 1 PoE 2 PoE 3
PoE Switch
LAN 1 LAN 2 LAN 3
Router
Uplink
LAN 1 LAN 2 LAN 3
Router

7. Enter the default username and password admin
into the User Name and Password elds
Setup Instructions
XXXYYYYZZZZ
8. If everything was setup correctly, on the connection
status, it will say connected. Click the play icon to start
viewing.
9. In the Device Manager, go back to the edit icon and
change the password (recommended).
XXXYYYYZZZZ

Setup Instructions
When Connected Standalone Wired
1. If connected standalone without a NVR, connect a
12V power adapter from the DC jack to an outlet and
then connect an Ethernet cable from the RJ45 jack to
the LAN port on a router
Power Adapter
3. Install the Device Search / Device Cong tool and
click the Search button to nd IP cameras on the
network
5. Click on the IP address to launch the web browser.
Download and run the Active X control. After installa-
tion, allow the Active X control to run. Once in, you are
now able to adjust the settings on the IP camera.
4. By default, the IP camera is set to static. In order to
login to the camera with the web browser (IE only),
highlight the IP camera and select the dropdown that
says static and change it to dynamic. Click on the
Modify to save the settings. You can also set your own
static IP as long as it matches your network LAN. For
dynamic IP addresses, make sure the router DHCP is
enabled. Note that you will need to allow access for the
application through your rewall. If not allowed, you
will not be able to change the IP address on the camera.
2. Alternatively, instead of connecting to a power
adapter, you can also connect it to a PoE switch via
Ethernet cable.
PoE 1 PoE 2 PoE 3
PoE Switch
LAN 1 LAN 2 LAN 3
Router
Uplink
LAN 1 LAN 2 LAN 3
Router

Setup Instructions
Connect Directly to the Camera’s AP
1. Another method to setup the camera is by connect-
ing directly to the camera’s access point (AP). By
connecting to the AP, you can then set it up to connect
to your own router’s AP. The initial setup procedure is
the same as “When Connected Standalone Wirelessly.”
The dierence is that when setting the camera wireless-
ly fails (either if you’re too far away from your router or
the password is incorrect), then the app will display the
camera’s access point and password. Connect to the
SSID of the camera and enter the password that is
provided. At that point, instead of connecting it via the
Cube option on the drop down, select IPC/NVR/DVR.
Scan the barcode of the camera, and enter the
password of the IP camera to connect.
3. Download and launch RXCamview from the App
Store or Play Store.
4. Click the human icon on the top left and then click
on Device List.
5. Click the +icon on the top right and click IPC/N-
VR/DVR from the dropdown.
6. The camera for the phone will open up. Scan the QR
code on the back of the IP camera.