SUN-FLY Vacuumsub A4 User manual
Vacuumsub A4
ORIGINING INSTRUCTION
Manual
Solution to your small to medium productivity demands of
3D vacuum sublimation(lm) printing
Contents
Important information 1
Safty information 2
Package contents 3
Overview 4
Mounting 5
Phone case jig install 6
Lunch box jig install 8
Emergency Button 9
Power Switch 10
Mouse jig install 7
Control panel overall 11
Vacuum sublimation process 15
WARNING
Head and understand
technical manual before
servicing This machine.
Failure to follow safety
instructions could result
in death or serious injury.
IMPORTANT INFORMATION
BRIEF INTRODUCTION
Please read this manual to understand the usage before any
operation on the vasuumsub A2/vacuumsub A3.
This manual includes product introduction, operating
instructions, and specications. SUN-FLY Internation
Business Development Ltd. maintains a policy of continually
This Vacuumsub A2 / Vacuumsub A3 is used to print on the surface of sublimation
blank phone cases.
Curve & Multiple-Surface Objects Dye-Sub Printing
The Vacuumsub A2/ Vacuumsub A3 brings you more possibilities of printing with curve or
multiple-surfaces sublimation blanks. This machine has a pneumatic drive pump built in that
generates a vacuum environment for the heat transfer process, which benets the sublimation
heat transfer printing quality and dramatically enhances eciency.
3D Objects Printable
Vacuum lm fully covers on printing objects.
Better Image Quality
Heating tubes evenly apply heat on to the surfaces.
Eciency
Easy panel operation.
This machine must be installed indoors to avoid rain and wind, which may aect the service life
of machine. It must be installed in the following environment: Ambient temperature: 5-40℃.
Relative humidity: 50% (40oC),90% (20oC), . Altitude: Maximum 1000m Transportation and
storage temperature: -25 - +55 ℃and for short periods (24h) up to 70°C Electric supply
tolerances: voltage +/-10%, frequency +/-1 Hz
Noise declaration: For a sound power level: Lwa= 70 dB (measured value) Associated
uncertainty K = 3 dB Measurement made in accordance with EN ISO 3746:1995. The Figures
quoted are emission levels and are not necessarily safe working levels. Whilst there is a
correlation between the emission and exposure levels, this cannot be used reliably to
determine whether or not further precautions are required. Factors that inuence the actual
level of exposure of the workforce includes the characteristics of the work room and the other
sources of noise etc. i.e. the number of machines and other adjacent processes. Also the
permissible exposure level can vary from country to country. This information, however, will
enable the user of the machine to make a better evaluation of the hazard and risk.
improving its product line and some illustrations and descriptions may vary from the machine
your own.
1
DANGER
HAZARDOUS
VOLTAGE.
Disconnect Power
before servicing.
CAUTION
Avoid abrasion
burn.
Always Wear
gloves.
Electric
This machine contains high voltage elements. To
prevent electric shock, do not open the machine cover
when the machine is on and in use. Additionally, do not
open the drive or control devices even if the power is o
when the power cord is plugged in.
Make sure the machine is power o and use a multi-meter to determine if the voltage has
dissipated before conducting any wiring adjustments or inspection.
Ensure the machine is grounded
Make sure wiring and other machine inspections are conducted by qualied technicians.
Any contact surface of human body should be completely dry to avoid electric shock when
operating the machine.
Fire
The internal temperature of the running machine is higher than 120℃, please make sure
keep all ammable materials away from the machine.
In the event of a machine failure disconnect the power supply, manually remove the
material loading pallet to avoid potential re risk.
A machine operator must be present when machine is turned on.
Others
Please use proper lifting tools to move the machine.
Do NOT stack, tilt or invert machine crate.
Do NOT expose the machine to rain or moisture.
Do NOT turn on or operate the machine if it is damaged, missing components, or
incorrectly congured.
Do NOT use the machine in explosive environment.
SAFTY INFORMATION
Make sure wearing heat resistant glove to prevent from
hurting before any operation on the loading board.
2
3
Package contents
7.Thermal Tubes
6.Metal board
1. Fuse
3. Spring
5. Capacitance
7. Thermal Tubes
6. Metal board
4. Tools
2. Ventilated aluminium rod
4.Tools
5.Capacitance
3.Screws
1.Fuse 2.Ventilated aluminium rod 3.Spring
Please check if any damages are made during shipping after receiving the machine package.
If the appearance of the package, machine or the accessories are damaged, please le a
written claim notice to the carrier immediately.
You may check all the accessories and parts according to the packing list, if any of the
accessories are missing, please contact the seller immediately.
4
1.Control Panel
3.Power O Button
7.Printing Jigs
4.Crank Handle
5.Emergency Button 6.Start Button
2.Power On Button
OVERVIEW
8.Power Switch
9.Power Connector
Model SFS-VSF07
Resistance screen
110V/220V 24A/12A
50KG
2700W
-0.08mPA
745 x 525 x 575mm
405 x 370mm
LCD Display
Power Supply
Weight
Power
Pressure
Body Size
Operating Area Size
4
5
1
2
3
6
7
89
5
Step 2Step 1
Step 3
Find the plug-in socket at
the back of the machine
Push it into the socket
Main power connector
nished
Mounting
6
Position the phone case jig
Push down the jig Push the jig towards to the
machine
Tighten the screws in accordance with the
corresponding red location of screws.
Step 1
Step 3
Step 5
Step 4
Step 2
Phone case jig install
Complete View
7
Push down the jig Push the jig towards to the
machine
Tighten the screws in accordance with the
corresponding red location of screws.
Position the mouse case jig
Step 2Step 1
Step 4Step 3
Step 5
Mouse jig install
Complete View
8
Step 3
Step 5
Step 4
Tighten the screws in accordance with the
corresponding red location of screws.
Step 2Step 1
Lunch box jig install
Push down the jig Push the jig towards to the
machine
Position the mouse case jig
Complete View
9
Emergency Button
Clockwise rotate the
emergency button to
restore the machine
operation
Press the emergency button
to stop the machine.
10
Power Switch
Turn o the power with
the switch upward.
Turn on the power with the
switch towards to right.
OFF
ON
11
CONTROL PANEL OVERALL
START
STOP
Heating Temperature
Preset Actual
Clear
Printed Circles
Printed Time
Count down
Machine Status
1 2 5
810
613 14 1434
791511 12
14. [Start] Option
16. [Setting] Option 15. [Stop] Option
13. Pilot Lamp
(Green lamp means machine temperature
reachesthe setting temperture. Red lamp
means did not reach.)
11. [Machine Status] icon 12. [Machine Status] Frame
9. [Count down] icon 10. [Count down] Frame
7.[Printing Time] icon 8. [Printing Time] Frame
5. Printed Circles Setting Frame 6. [Clear] Option
1. [Heating Temperature ] icon 2. Temperature Setting Frame
3.Actual Temperature Frame 4. Printed Circles icon
12
Step 1.Touch the [Heating Temperature] Setting Frame
Step 3. Press [Enter] to conlm setting
Setting Finshed
Red lamp means the
hood did not reach the
setting temperature
Hood Heating Temperature Setting
Step 2. Set the temperature
by pressing the number
directly
START
STOP
Heating Temperature
Printed Circles
Printed Time
Count down
Machine Status
105
0~160
7 8 9
4 5 6
1 2 3
0.Clear
ESC Enter
START
STOP
Heating Temperature
Preset Actual
Clear
Printed Circles
Printed Time
Count down
Machine Status
START
STOP
Heating Temperature
Preset Actual
Clear
Printed Circles
Printed Time
Count down
Machine Status
105℃105℃
Idle
Idle
13
Printing time setting
Step 1.Touch [printing
Time Preset] Frame
Step 2. Set the printing time
by pressing the number
directly
Step 3. Press [Enter] to conrm setting
Setting Finshed
START
STOP
Heating Temperature
Printed Circles
Printed Time
Count down
Machine Status
270
0~9999
7 8 9
4 5 6
1 2 3
0.Clear
ESC Enter
START
STOP
Heating Temperature
Preset Actual
Clear
Printed Circles
Printed Time
Count down
Machine Status
START
STOP
Heating Temperature
Preset Actual
Clear
Printed Circles
Printed Time
Count down
Machine Status
Idle
105℃
270 sec.
105℃
Idle
14
Setting
sec.
sec.
sec.
sec.
sec.
Set [Film preheat time]
This time setting is to heat up
the lm to make it softer, avoiding
from the lm getting wrinkle when
proceed to the next vacuum
sublimation step. Recommended
time is 3 seconds.
Touch [setting] option
next page
Set[Protechion Time]
This time setting is to protect the
lm from being overheated before
you start printing. Recommended
time is 7 seconds.
Step 2. Touch the [Bottom Temperature]
Setting Frame
Choose language
Set [Heating Delay Time]
This time setting is in order to prevent
the lm from being in a high
temperature environment in a long
period and lead the lm to be
excessive softening and baked.
Recommended time is 7 seconds.
Consistent Heating Time setting denes constant heating period of the thermal tubes
during the entire vacuum sublimation printing process, and Heating Pause Time setting is to
pause the thermal tubes heating up after Consistent Heating Time period. Both two time
settings are in order to prevent the printing process from being in a state of overheating and
aect the printed result. The Consistent Heating Time is recommended 8 seconds and the
Heating Pause Time is 23 seconds.
Bottom Temperature
Preset Actual
Film Preheat Time
Protechion Time
Printed Circles Count
105℃
7
7
8
23
1
3
105℃
Exit
Next
中文 English
Heating Delay Time
Consistent Heating Time
Heating Pause Time
Exit
START
STOP
Heating Temperature
Preset Actual
Clear
Printed Circles
Printed Time
Count down
Machine Status
Press [Exit] to quit out
Press[Exit] to quit out
15
Vacuum sublimation process
Step 1
Step 4Step 3
Put the phone case on
to the printing jig.
Step 2
Put in the jigs for about
30 minutes preheat.
Put the printed lm over the cases.
Gloss side should be on the top
Press the Power On button and set the
numerical value according to Step 7
16
Step 6
Step 8
Step 5
Step 9
Close the positioner Push the platen inside the machine
Printing nished,pull out the table
Step 7
Set the printing temperature , printing time
and the time for lm preheat. Press the START
switch to begin the printing process.
Open the positioner then take out
the lm and the phone cases
START
STOP
Heating Temperature
Preset Actual
Clear
Printed Circles
Printed Time
Count down
Machine Status
105℃
270 sec.
105℃
Idle
SUN-FLY International Business Development Ltd.
China
Room 01,3F,TengHui Building,#28,
ZhuCun BeiHuan Road,TianHe District,
GuangZhou,China.510660
Tel: +86 20 8738 6048
Fax: +86 20 8738 0348
Email: info@sun-y.com
www.sun-y-sublimation.com
This manual suits for next models
1
Table of contents
