KLINCH-PAK KP-SWM User manual

1320 Tower Road Schaumburg, IL 60173
Phone: [phone] Fax: [phone]
KP-SWM Manual Carton Stapler
MANUAL/WARNING:
IMPORTANT PLEASE READ BEFORE USING TOOL
Please read the following operating instructions manual.
Refer to this manual for safety, adjustment and trouble
shooting instructions. If you have any further questions
please contact your distributor.

2
1320 Tower Road Schaumburg, IL 60173
Phone: [phone] Fax: [phone]
NOTES

3
1320 Tower Road Schaumburg, IL 60173
Phone: [phone] Fax: [phone]
PAGE
TOOL SPECIFICATIONS .......................................................................................................................4
SAFETY INSTRUCTIONS ......................................................................................................................5
LUBRICATION AND MAINTENANCE ....................................................................................................6
ADJUSTING FOR STAPLE LEG LENGTH ............................................................................................6
CLINCH ADJUSTMENT..........................................................................................................................7
DEPTH ADJUSTMENT...........................................................................................................................7
EXPLODED VIEW OF TOOL..................................................................................................................8
PARTS LIST............................................................................................................................................9
TROUBLE SHOOTING .........................................................................................................................10
TABLE OF CONTENTS

4
1320 Tower Road Schaumburg, IL 60173
Phone: [phone] Fax: [phone]
MODEL OF TOOL ………………………………………………..…………….KP-SWM
DIMENSIONS （LENGTH x HEIGHT x WIDTH） ............................................ 15" x 4.5" x 11.5"
WEIGHT （WITHOUT FASTENERS） ............................................................... 3.75 lbs
COMPRESSED AIR：
MAXIMUM PERMISSIBLE OPERATING PRESSURE .............................. N/A
RECOMMENDED OPERATING PRESSURE............................................ N/A
AIR CONSUMPTION .................................................................................. N/A
STAPLE SPECIFICATION ......................................................................... 1-3/8" CROWN
LEG LENGTH 5/8", 3/4"
STAPLE CAPACITY.................................................................................... 100 PCS (2 Strips)
THE NOISE LEVELS: (AT THE WORKPLACE, ALWAYS WEAR HEARING PROTECTION EQUIPMENT.)
A WEIGHTED SINGLE EVENT SOUND PRESSURE LEVELAT OPERATOR’S POSITION:……… N/A
A WEIGHTED SINGLE EVENT SOUND POWER LEVEL.......................................................N/A
A WEIGHTED SINGLE EVENT SURFACE SOUND PRESSURE LEVEL ..............................N/A
TOOL SPECIFICATIONS

5
1320 Tower Road Schaumburg, IL 60173
Phone: [phone] Fax: [phone]
SAFETY INSTRUCTIONS
• Warning: Read this manual and understand all safety instructions before operation of
the tool. If you have any questions, please contact our Authorized Representatives.
• Always wear safety goggles when operating tool.
• Always handle with care.
• Do not place your hand or any other body part near or around the staple clinching area.
• Always makes sure the tool is resting on the carton you are trying to seal. Do not point
tool towards anyone.

6
1320 Tower Road Schaumburg, IL 60173
Phone: [phone] Fax: [phone]
ADJUSTING FOR STAPLE LEG LENGHT
• Loosen the set screw (526 on Schematic) with a 3 mm Hex Key
• Turn adjusting rod (018 on Schematic) 180 degrees with a flat head screw drive to
the desired setting. See diagram A, for positioning explanation.
• Tighten Set Screw (526) when positioned to desired setting.
A.

7
1320 Tower Road Schaumburg, IL 60173
Phone: [phone] Fax: [phone]
DEPTH ADJUSTMENT
• Loosen the Front Screw (527 on the Schematic) with a 6 mm Hex Key.
• Push the body (007) up and adjust to desired depth.
• When top edge of the adjustment plate (019) is at it's highest setting the teeth are
at their shallowest penetration. If set at lowest position, the teeth are at their
deepest penetration. See diagram C.
C.
CLINCH ADJUSTMENT
• Use 3mm Rod or 2.5mm Hex Key to turn the collar (006 on Schematic) found in
the front window of the tool. Rotate clockwise for tighter clinch.
Counterclockwise for the loose setting. See diagram B.
B.

10
1320 Tower Road Schaumburg, IL 60173
Phone: [phone] Fax: [phone]
TROUBLE SHOOTING
PROBLEM CAUSE REMEDY
EXCESSIVE JAMS: ANVIL SCREWS (510) LOOSE. TIGHTEN SCREWS (510)
STAPLE SIZE IS WRONG. USE THE PROPER SIZE STAPLE.
UNEVEN CLINCH WRONG STAPLE SIZE CHECK FOR PROPER CHLINCH &
LEG LENGTH ADJUSTMENT
UNCLINCHED STAPLE ANVIL (015,016) LOOSE TIGHTEN ANVIL (015,016)
ANVIL (015,016) ARE BROKEN REPLACE ANVIL (015,016)

11
1320 Tower Road Schaumburg, IL 60173
Phone: [phone] Fax: [phone]
Products offered by
Call today for more details

1320 Tower Road Schaumburg, IL 60173
Phone: [phone] Fax: [phone]
Visit our web site
www.axxisus.com
Or
Email us @
r[email protected]