Sun Microsystems Sun Ultra 60 User manual

10
1
Operating and Service Positions
Operating Position
The Sun Ultra 60 system must be operated in a vertical position.
Service Position
Place the system in the horizontal service position on a hard
surface to perform service on the system.
JP tasks
KR tasks
TW tasks
PRC tasks

11
1

12
2
Opening the System Unit
1. Press the Standby ( ) side of the power switch.
2. Remove the lock block from the system.
3. Grasp the side panel and pull it toward the back of the system.
Lift up and remove the panel.
JP tasks
KR tasks
TW tasks
PRC tasks

13
2

14
3
Installing DIMMs
Note - Use only dual in-line memory modules (DIMMs) that are
specifically designed for your Sun Ultra 60 system. See ( 11).
1. Power off your system and open the system unit ( 2).
2. Locate the wrist strap, and attach its adhesive copper strip to
the chassis back panel. Wrap the other end twice around your
wrist, with the adhesive side against your skin.
3. Use a Phillips screwdriver to loosen the four screws that hold
the power supply to the chassis. Disconnect the power harness
plug from the connection at the motherboard. Slide the power
supply partially out until it is not blocking the DIMMs.
4. Locate and select an available bank of DIMM slots on the
motherboard. See ( 12).
JP tasks
KR tasks
TW tasks
PRC tasks

15
3

16
3
Installing DIMMs
5. Unpack the DIMM, holding it only by the edges.
6. For each DIMM, align the notch on the side of the DIMM with
the ejector on the DIMM slot. Insert the DIMM into the slot.
7. Push the DIMM firmly into its connector until you hear a “click.”
8. Slide the power supply back into the chassis. Reconnect the
power harness plug to the connection at the motherboard. Use
a Phillips screwdriver to tighten the four screws that attach the
power supply to the chassis.
9. Detach the wrist strap and close the system unit ( 10).
JP tasks
KR tasks
TW tasks
PRC tasks

17
3

18
4
Changing the RS-423/232 Jumpers
Note — If you are connecting your system to a public X.25 network,
you may need to change the serial port mode jumpers from RS-423
to RS-232 mode.
1. Power off the system and open the system unit ( 2).
2. Locate the wrist strap, and attach its adhesive copper strip to
the chassis back panel. Wrap the other end twice around your
wrist, with the adhesive side against your skin.
3. Use a Phillips screwdriver to loosen the four screws that hold
the power supply to the chassis. Slide the power supply partially
out such that it is not blocking the jumpers.
Note — The power cord must remain plugged into the power
source.
JP tasks
KR tasks
TW tasks
PRC tasks

19
4

20
4
Changing the RS-423/232 Jumpers
4. Locate the jumpers on the motherboard ( 12). Change the
jumpers on J2605 and J2604 to the RS-232 position.
5. Slide the power supply back into the chassis. Use a Phillips
screwdriver to tighten the four screws that attach the power
supply to the chassis.
6. Detach the wrist strap and close the system unit ( 10).
JP tasks
KR tasks
TW tasks
PRC tasks

21
4
J2702
J2703
J2605
J2604
J2801
J0103
J3001
J2804
RS-232
J2604
RS-232
J2605

22
5
Installing the Hard Disk Drive
Note — Use only hard disk drives that are specifically designed for
a Sun Ultra 60 system.
1. Power off the system and open the system unit ( 2).
2. Locate the wrist strap, and attach its adhesive copper strip to
the chassis back panel. Wrap the other end twice around your
wrist, with the adhesive side against your skin.
3. Locate the hard drive bay.
JP tasks
KR tasks
TW tasks
PRC tasks

23
5

24
5
Installing the Hard Disk Drive
4. Remove the hard disk drive from the antistatic bag. Read the
hard disk drive product guide for information about jumper
switch settings or other installation tasks.
JP tasks
KR tasks
TW tasks
PRC tasks

25
5

26
5
Installing the Hard Disk Drive
5. Open the drive handle and slide the drive completely into the
drive bay. Press the drive to connect it to the SCSI port in the
system.
6. Close the drive handle. The handle will not latch if the drive is
not properly attached or closed.
7. Detach the wrist strap and close the system unit ( 10).
JP tasks
KR tasks
TW tasks
PRC tasks

27
5

28
6
Installing the Diskette Drive or Accessory Device
1. Power off the system and open the system unit ( 2).
2. Locate the wrist strap, and attach its adhesive copper strip to
the chassis back panel. Wrap the other end twice around your
wrist, with the adhesive side against your skin.
3. Remove the peripheral bezel from the front of the system unit.
4. Use a Phillips screwdriver to loosen the two screws holding the
removable media assembly (RMA) to the system chassis.
5. Slide the RMA out of the system chassis.
JP tasks
KR tasks
TW tasks
PRC tasks

29
6