Sun Microsystems StorEdge D2 User manual

Sun Microsystems, Inc.
4150 Network Circle
Santa Clara, CA 95054 U.S.A.
650-960-1300
Send comments about this document to: [email protected]
Sun StorEdge™
D2 Array Cabinet Installation Guide
Part No. 816-1696-11
February 2002, Revision A

Copyright 2002 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, CA 95054 U.S.A. All rights reserved.
This product or document is distributed under licenses restricting its use, copying, distribution, and decompilation. No part of this product or
document may be reproduced in any form by any means without prior written authorization of Sun and its licensors, if any. Third-party
software, including font technology, is copyrighted and licensed from Sun suppliers.
Parts of the product may be derived from Berkeley BSD systems, licensed from the University of California. UNIX is a registered trademark in
the U.S. and other countries, exclusively licensed through X/Open Company, Ltd.
Sun, Sun Microsystems, the Sun logo, AnswerBook2, docs.sun.com, Sun StorEdge, Sun Fire, and Solaris are trademarks, registered trademarks,
or service marks of Sun Microsystems, Inc. in the U.S. and other countries. All SPARC trademarks are used under license and are trademarks or
registered trademarks of SPARC International, Inc. in the U.S. and other countries. Products bearing SPARC trademarks are based upon an
architecture developed by Sun Microsystems, Inc. The Energy Star logo is a registered trademark of EPA. Adobe is a registered trademark of
Adobe Systems, Incorporated.
The OPEN LOOK and Sun™ Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sun acknowledges
the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry. Sun
holds a non-exclusive license from Xerox to the Xerox Graphical User Interface, which license also covers Sun’s licensees who implement OPEN
LOOK GUIs and otherwise comply with Sun’s written license agreements.
Federal Acquisitions: Commercial Software—Government Users Subject to Standard License Terms and Conditions.
DOCUMENTATION IS PROVIDED “AS IS” AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT,
ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID.
Copyright 2002 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, CA 95054 Etats-Unis. Tous droits réservés.
Ce produit ou document est distribué avec des licences qui en restreignent l’utilisation, la copie, la distribution, et la décompilation. Aucune
partie de ce produit ou document ne peut être reproduite sous aucune forme, par quelque moyen que ce soit, sans l’autorisation préalable et
écrite de Sun et de ses bailleurs de licence, s’il y en a. Le logiciel détenu par des tiers, et qui comprend la technologie relative aux polices de
caractères, est protégé par un copyright et licencié par des fournisseurs de Sun.
Des parties de ce produit pourront être dérivées des systèmes Berkeley BSD licenciés par l’Université de Californie. UNIX est une marque
déposée aux Etats-Unis et dans d’autres pays et licenciée exclusivement par X/Open Company, Ltd.
Sun, Sun Microsystems, le logo Sun, AnswerBook2, docs.sun.com,Sun StorEdge, Sun Fire, et Solaris sont des marques de fabrique ou des
marques déposées, ou marques de service, de Sun Microsystems, Inc. aux Etats-Unis et dans d’autres pays. Toutes les marques SPARC sont
utilisées sous licence et sont des marques de fabrique ou des marques déposées de SPARC International, Inc. aux Etats-Unis et dans d’autres
pays. Les produits portant les marques SPARC sont basés sur une architecture développée par Sun Microsystems, Inc. Adobe est une marque
enregistree de Adobe Systems, Incorporated.
L’interface d’utilisation graphique OPEN LOOK et Sun™ a été développée par Sun Microsystems, Inc. pour ses utilisateurs et licenciés. Sun
reconnaît les efforts de pionniers de Xerox pour la recherche et le développement du concept des interfaces d’utilisation visuelle ou graphique
pour l’industrie de l’informatique. Sun détient une licence non exclusive de Xerox sur l’interface d’utilisation graphique Xerox, cette licence
couvrant également les licenciés de Sun qui mettent en place l’interface d’utilisation graphique OPEN LOOK et qui en outre se conforment aux
licences écrites de Sun.
Achats fédéraux : logiciel commercial - Les utilisateurs gouvernementaux doivent respecter les conditions du contrat de licence standard.
LA DOCUMENTATION EST FOURNIE “EN L’ETAT” ET TOUTES AUTRES CONDITIONS, DECLARATIONS ET GARANTIES EXPRESSES
OU TACITES SONT FORMELLEMENT EXCLUES, DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE, Y COMPRIS NOTAMMENT
TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE, A L’APTITUDE A UNE UTILISATION PARTICULIERE OU A
L’ABSENCE DE CONTREFAÇON.

1
Cabinet Installation
This document describes how to mount Sun StorEdge D2 arrays in Sun cabinets.
Refer to the following manual how to set up before installation and how to finish
installation and configuration after the array is mounted in the cabinet:
■Sun StorEdge D2 Array Installation, Operation, and Service Manual
Note – You need a Philips screwdriver to perform the procedures in this manual.
Shipping Box Contents
The shipping box for the cabinet-mountable (also called rack-mountable) Sun
StorEdge D2 array contains the following items needed for installing the array in a
Sun cabinet.
TABLE 1 Inventory for the Cabinet-mountable Sun StorEdge Array
1 Sun StorEdge D2 array with mounting tray attached
2 Mounting brackets
16 10-32 x 1/2 in screws
2 Trim strips with four 10-14 x 7/16 in screws attached

2Sun StorEdge D2 Array Cabinet Installation Guide • February 2002
The shipping box for the conversion kit contains the following items needed for
modifying a tabletop array so that the array can be mounted in a Sun cabinet.
Overview of Tasks for Mounting Arrays
TABLE 3 lists the tasks required for mounting a Sun StorEdge D2 array in a Sun
cabinet along with links to where the tasks are documented.
TABLE 2 Rackmount Conversion Kit Inventory
1 Mounting tray
2 Mounting brackets
16 10-32 x 1/2 in screws
2 Trim strips with four 10-14 x 7/16 in screws attached
4 10-14 x 7/16 in screws
TABLE 3 Tasks for Mounting Arrays
Task Where Documented
Find out which mounting holes to use in the cabinet. Rackmount Placement Matrix (RPM)at
www.sun.com/products-n-
solutions/hardware/docs/Network_Storage_S
olutions/Cabinets_and_Enclosures.
For an example using the table for the Sun StorEdge
Expansion Cabinet, go to: “Using the Mounting Hole
Numbers in the RPM” on page 3.
Install the tray on the array if you are upgrading a
tabletop array to rackmount it.
“To Install a Tray on an Array” on page 5
Connect the mounting brackets to the cabinet. “To Connect the Mounting Brackets to a Cabinet” on
page 7
Install the array into the cabinet. “To Install an Array in a Cabinet” on page 10

Cabinet Installation 3
Using the Mounting Hole Numbers in
the RPM
This section provides the information you need to use the mounting hole numbers
provided in the Rackmount Placement Matrix (RPM) when you are installing a Sun
StorEdge D2 array.
Vertical mounting space is defined in rack units (RUs). Sun StorEdge D2 arrays are 4
RU units high. One RU equals 1.75 in (4.44 cm), which is the total of the distances
between the repeating pattern of the mounting holes that make up one RU: .5 in
(1.27 cm) + .625 in (1.59 cm) + .625 in (1.59 cm). RU boundaries are in the center of
the holes that are spaced .5 in (1.27 cm) apart. The hole spacing for a single RU is
illustrated at the lower right of FIGURE 1.
FIGURE 1 Cabinet Hole and RUs, Spacing and Numbering
The hole numbers start with 1 at the bottom and are stamped on the metal in
increments of 10 (as illustrated in FIGURE 1). Holes in the metal mounting rails at the
front, the back, and the sides of the cabinet all have the same numbers. Also as
shown in FIGURE 1, the arrays are installed from the bottom of the cabinet up.
Space occupied by 4U Array
Space occupied by 4U Array
1
10
20
30
.5 in.
.5 in.
.625 in.
.625 in.
Space occupied by the first 4 RU array
Hole spacing for one RU
Space occupied by the second 4 RU array

4Sun StorEdge D2 Array Cabinet Installation Guide •February 2002
A table in the RPM gives the number of RUs in each Sun cabinet. For example, the
Sun StorEdge Expansion Cabinet is a 36 RU cabinet, with space for up to nine Sun
StorEdge D2 arrays.
TABLE 4 is an example from the RPM showing the mounting holes to use when
installing Sun StorEdge D2 arrays in a Sun StorEdge Expansion Cabinet. See the
RPM for other tables that list mounting holes for installing these arrays in other
qualified cabinets.
TABLE 4 Holes for Mounting Sun StorEdge D2 Arrays in Sun StorEdge Expansion
Cabinets
The column headings in TABLE 4 are explained in the following list:
■Array
Numbers corresponding to the order of installation of the arrays. Installation
proceeds from the bottom of the cabinet up (as indicated in FIGURE 1), with 1
being the first array, 2 being the second, and so on.
■Mounting Brackets to Cabinet
Hole numbers to use when installing the screws that secure the mounting
brackets to the cabinet.
For an illustration of the screws that secure the mounting brackets, see “To
Connect the Mounting Brackets to a Cabinet” on page 7.
■Tray to Cabinet
Hole numbers to use when installing the screws that secure the tray to the cabinet
For an illustration of the placement of the screws that secure the tray to the
cabinet, see FIGURE 7.
The hole numbers from the first row of TABLE 4 are used in examples throughout this
manual.
Array Mounting Brackets to Cabinet Tray to Cabinet
1 8,12 11,14
2 20,24 23,26
3 32,36 35,38
4 44,48 47,50
5 56,60 59,62
6 68,72 71,74
7 80,84 83,86
8 92,96 95,98
9 104,108 107,110

Cabinet Installation 5
Procedures
▼To Install a Tray on an Array
Use an 8 in lb torque Philips screwdriver to start the holes. Tighten the screws with
an 18 in lb torque driver.
Caution – This procedure requires two people to lift and move the array. Use care
to avoid injury. A array with a tray attached may weigh up to
64 pounds (29 kg).
1. With the aid of an assistant, invert the array with the front facing you (FIGURE 2).
2. Remove the feet.
Discard the feet and screws. They are not reused.
FIGURE 2 Removing the Feet
!

6Sun StorEdge D2 Array Cabinet Installation Guide •February 2002
3. Place the tray on the array (FIGURE 3).
FIGURE 3 Installing the Mounting Tray on the Chassis
4. Loosely thread four 10-14 x 7/16-in screws into the four holes.
5. When all screws are started, tighten them to 18 in/lb.
6. With the aid of an assistant, restore the array to the upright position with the front
of the array facing you.
7. Go to “To Connect the Mounting Brackets to a Cabinet” on page 7.

Cabinet Installation 7
▼To Connect the Mounting Brackets to a Cabinet
Use an 8 in lb torque Philips screwdriver to start the holes. Tighten the screws with
an 18 in lb torque driver.
Have the Rackmount Placement Matrix table handy that applies to your cabinet.
Note – The mounting brackets are identical, and they can be installed in either side
of the cabinet. Install the brackets from the bottom of the cabinet to the top.
1. Remove the front panel or door from the cabinet.
2. Remove the vented rear door from the cabinet.
Refer to the cabinet’s documentation for how to perform the first two steps.
3. Attach the mounting brackets using the designated holes in the brackets and the
designated holes in the cabinet’s rails.
Insert the screws through the designated holes in the brackets shown in FIGURE 4
into the rail holes.
For the appropriate rail hole numbers, see the “Mounting Brackets to Cabinet”
column in the table from the RPM that applies your cabinet.
For example, when installing the brackets for the first array in a Sun StorEdge
expansion cabinet, you would put the screws into the rail holes numbered 12 and the
8, which are assigned to Array 1 in the following row from TABLE 4.
a. Loosely thread four 10-32 x 1/2 in screws through the bracket into the holes
with the same number on the front and back rails on both sides of the cabinet.
Insert each screw into the highest-numbered hole specified in the “Mounting
Brackets to Cabinet” column. When installing the first array in a Sun StorEdge
Expansion cabinet, you would insert one screw through the left bracket into hole
12 on the front mounting rail and another screw through the same bracket into
hole 12 on the back rail. Then on the right side of the cabinet you would insert
two more screws through the right mounting bracket into the corresponding rail
holes numbered 12.
Array Mounting Brackets to Cabinet Tray to Cabinet
1 8,12 11,14

8Sun StorEdge D2 Array Cabinet Installation Guide •February 2002
b. Using the top holes designated for your cabinet in FIGURE 4, place the bracket
on the screws.
FIGURE 4 shows the top holes to use for Sun Fire cabinets and the top holes to use
for other cabinets.
For example, if you are mounting the array in a Sun StorEdge Expansion Cabinet,
you would slide the mounting bracket holes designated for “other cabinets” over
the screws you attached to the mounting rails in the previous step.
FIGURE 4 Top Holes for Securing the Mounting Bracket to the Cabinet
i. Take a mounting bracket.
ii. Place the top holes of the mounting bracket onto the appropriate screws on
each side.
iii. Slide the bracket down so that the tops of the holes rest on the screws.
Top holes for other cabinets
Left Right
Cabinet Back
Cabinet Front
Top holes for other cabinets
Top holes for Sun Fire cabinets Top holes for Sun Fire cabinets