Sun Microsystems Enterprise 4000 Installation instructions manual

Installing the Server Chassis
1. Remove the front door of the cabinet.
■For an expansion cabinet, lift the door off the hinge pins.
■For a server cabinet, pull off the front panel, then lift the door.
2. Lower the leveling pads to ensure that the cabinet cannot move.
Caution – The next two steps require two people.
3. Turn the Ultra Enterprise 4000 chassis right side up.
4. Slide the chassis and base plate onto the rails.
5. Secure the base plate to the side rails with four 10-32 x 1/2 inch
screws, two screws at the front and two screws at the rear.
6. Connect the chassis to the power sequencer:
■For chassis 1, disconnect the AC cable of the rack fan tray from socket
J2 and connect the AC cable to J6, then connect the Enterprise 4000
chassis to socket J2.
■For chassis 2, use socket J7.
■For chassis 3, use socket J11.
!
Ordering Sun Documents
SunDocsSM is a distribution program for technical documentation and is
available from SunExpress. You can find a full listing of available
documentation on the World Wide Web:
http://www.sun.com/sunexpress/
To order or for more information:
Telephone: [phone] (United States and Canada only)
Fax: [phone] (United States and Canada only)
Reader Comments
Your comments and suggestions are important to us. Please let us know
what you think about the Sun Enterprise 4000 Rack-Mounting Instructions,
part number 802-7249-11.
You can send detailed comments via email to [email protected], or
send a fax to SMCC Doc Feedback at [phone].
Sun™
E
Rack
m
Part Number: 802-7249-11
Revision A of December 1997
Copyright 1997 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. Third-party
software, including font technology, is copyrighted and licensed from Sun suppliers. Sun, Sun
Microsystems, the Sun Logo, SunDocs, and Solaris are trademarks or registered trademarks of Sun
Microsystems, Inc. in the U.S. and other countries. RESTRICTED RIGHTS: Use, duplication, or
disclosure by the U.S. Government is subject to restrictions of FAR 52.227-14(g)(2)(6/87) and FAR 52.227-
19(6/87), or DFAR 252.227-7015(b)(6/95) and DFAR 227.7202-3(a).
Copyright 1997 Sun Microsystems, Inc. Tous droits réservés. Distribué par des licences qui en
restreignent l’utilization. Le logiciel détenu par des tiers, et qui comprend la technologie relative aux
polices de caractères, est protégé par un copyright et licencié par des fournisseurs de Sun. Sun, Sun
Microsystems, le logo Sun, SunDocs, et Solaris sont des marques de fabrique ou des marques déposées de
Sun Microsystems, Inc. aux Etats-Unit et dans d’autres pays.
Sun Microsystems Computer Company • 901 San Antonio Road • Palo Alto, CA 94303-4900
USA • 650-960-1300 • Fax [phone]
7. Route the interface cables as appropriate and connect them to the
Enterprise 4000 chassis.
8. Reattach the upper bezel (which shows the keyswitch positions).
Start at the back edge, then swing the front down until the locking tabs
click into place.
Note – If it is necessary to remove the bezel, the locking tabs
will be easier to reach if you remove the four screws that secure
the base plate to the side rails (shown in the previous drawing)
and pull the chassis out approximately 1 inch (2.5 cm). Secure
the base plate again afterward.
9. Replace the front door.

Installing the Rackmount Kit
1. Place the base plate on the bottom of the chassis.
The front of the base is angled away from the chassis.
2. Use four M6x10 screws to attach the base plate to the bottom of the
Ultra Enterprise 4000 chassis.
3. Attach the left rail to the rack:
a. Refer to the Rackmount Placement Matrix to determine which
mounting holes you will use. The screw holes on the rack are
numbered for easy identification.
b. Loosely fit the two top screws in the sides of the rack.
c. Slide the rail onto the screws.
d. Install the four remaining screws, then tighten all six screws.
4. Install the right side rail in the same manner.
4. Remove the top panel:
a. Remove the square inserts from the corners of the top panel.
Press the small dot to tilt an insert up, then lift it off.
b. Lift the front corners of the top panel 1/8 inch (3 mm).
There are two locking tabs at the front corners of the panel.
c. Push the panel back 1 inch (2.5 cm), then lift it off.
5. Remove the bottom panel:
a. Turn the chassis upside down.
b. Remove the four feet by removing the screw that holds each foot.
c. Lift the front corners of the bottom panel, push the panel toward
the back of the chassis, and lift the panel off.
6. Remove the lower bezel:
a. With the chassis still upside down, use a flat-bladed screwdriver
to lift the left side of the lower bezel approximately 1/8 of an inch
(3 mm).
b. Slide the bezel 1/4 of an inch (6 mm) to the left and lift it off.
Side panel
Top panel
Side panel
Upper bezel
Lower bezel Foot
Square insert
Bottom panel
For mounting locations in a system or expansion cabinet, refer to the
Rackmount Placement Matrix (part number 802-6945-11, or later).
If there are three Ultra™ Enterprise™ 4000 chassis in a rack, you must also
install the Ultra Enterprise Cabinet Air Baffle (part number X9601A).
Note – The chassis is heavy. In the following procedures, two
people are required to move the chassis.
Inventory
The rack-mounting kit contains:
Removing the Outer Panels
1. Disconnect all cables from the Enterprise 4000 chassis.
2. Remove the upper bezel:
a. Press the lower left and right sides of the upper bezel to release
the locking tabs.
b. Swing the bottom edge of the bezel toward you to release the tabs
in the top of the bezel, then lift the bezel off.
3. Remove the right and left side panels:
a. Push the side panel back approximately 3/4 of an inch (2 cm).
b. Pull the bottom of the panel away from the side, then lift the
panel off.
Mounting tabs are located at top of the panel.
• Left rail
• Right rail
• Base plate
• 4 Screws, M6 x 10 mm
• 16 Screws, 10-32 x 1/2 inch