Sunbeam Open All User manual

Open All
Electric Can Opener
INSTRUCTION BOOKLET.
CA2800
PLEASE READ THIS BOOK THOROUGHLY AND RETAIN FOR FUTURE REFERENCE.

Sunbeam’s Safety Precautions.
Sunbeam are very safety conscious when designing
and manufacturing consumer products, but it is
essential that the product user also exercise care
when using an electrical appliance. Listed below are
precautions which are essential for the safe use of
an electrical appliance:
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove by
grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug when
the appliance is not in use and before cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked and
tested by a qualified technician or service person.
• Always use your appliance from a power outlet
of the voltage (A.C. only) marked on the
appliance.
• Close supervision is necessary when your
appliance is being used near children or infirm
persons.
• Never leave an appliance unattended
while in use.
• Young children should be supervised to ensure
that they do not play with the appliance.
• Do not use an appliance for any purpose other
than its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven. Do
not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• For safety reasons and to avoid maintenance by
unskilled persons, some appliances are ‘sealed’
using tamperproof screws. Such appliances
should always be returned to the nearest
Sunbeam Appointed Service Centre for
adjustment or repair if required.
• Do not operate any electrical appliance with a
damaged cord or after the appliance has been
dropped or damaged in any manner. If damage is
suspected, return the appliance to the nearest
Sunbeam Appointed Service Centre for
examination, repair or adjustment.
• For additional protection, Sunbeam recommend
the use of a residual current device (RCD) with a
tripping current not exceeding 30mA in the
electrical circuit supplying power to your
appliances.
• Do not immerse the appliance in water or any
other liquid unless recommended.
SAFETY PRECAUTIONS FOR ALL ELECTRICAL APPLIANCES
If you have any concerns regarding the performance and use of your appliance, please ring our Toll Free number
(Australia only) 1800 025 059. New Zealand - contact the Sunbeam Office in Auckland on 09 912 0747.
Ensure the above safety precautions are understood.
• Keep fingers well away from blade when
in use.
• Use extreme care when handling blades.
• Do not place any part of this appliance in
a dishwasher.
• Use extreme care when handling off-cuts.
SAFETY PRECAUTIONS FOR YOUR OPEN ALL.

Stainless steel blade cutting action
Stainless steel blade allows for a smoother
cutting action.
Magnetic lid holder
Holds the lid in place during and after the can is
fully opened.
Removable lever
For easy cleaning, slide the release button
and remove the cutting assembly/lever.
Automatic operation
Simply lift the lever and position the blade inside
the rim of the can. Press the lever down and the
Open All will automatically stop when the can is
fully opened.
Knife sharpener
Built in ceramic knife sharpener will ensure that
your knives remain sharp at all times.
Cord storage
Handy cord storage keeps the benchtop tidy by
storing unwanted cord.
Features of your new Sunbeam Open All.
Cutting Assembly
Release Button
Support Bar
Drive Wheel
Knife Sharpener
Cord Storage
Lever
Magnetic Lid Holder
Blade

1. Ensure that the Cutting Assembly is correctly
positioned. (see figure 1.)
1. The Cutting Assembly fits into the keyhole
opening at the top of the Open All, above the
Drive Wheel. Slide the Release Button to the
right as the Cutting Assembly is inserted, it
will “click” into position, with the release
button returning to its original position.
2. Insert the plug into a 230-240 volt power
outlet and turn the power on.
3. Hold the lever in the upright position. Position
the can under the Support Bar so that the rim
of the can rests on top of the Drive Wheel,
tilting the can at a slight angle towards the
main body of the unit. (See figure 2.)
4. Firmly press the Lever down. This action will
bring the blade down and pierce the lid of the
can and start operating the motor to turn the
can. Ensure the Magnetic Lid Holder is in
contact with the lid of the can. (See figure 3.)
5. When the can begins to turn, it is no longer
necessary to hold down the lever.
6. When the can is fully opened, the Open All
will stop automatically.
7. To remove the can, support the can with one
hand and lift the Lever with the other. The lid
will remain attached to the Magnetic Lid
Holder. (see figure 4.)
CAUTION: Be careful when removing the lid
from the magnet as the cut edge is sharp.
Opening dented/damaged cans: Occasionally,
badly dented cans will cause the Open All to
stall. If this happens, grasp the dented can and
guide it through the cutting action manually
until the damaged areas are opened.
Jammed cans: To continue opening a can that
has become jammed, raise the lever and release
the can. Begin the cutting action again in a new
position on the can lip.
Sharpening knives: Support the Open All on top
with one hand. With the other guide the knife
through the unique ceramic block at the back of
the Open All. Repeat this action until you are
satisfied with the sharpness of your knife.
Using your Sunbeam Open All.
Figure 1.
Figure 3.
Figure 4.
Figure 2.
Drive wheel
Keyhole
Release button
Support
bar lever
Drive
wheel

Turn the power off and unplug the cord from
the power outlet before cleaning. The Cutting
Assembly is easily removed for thorough
cleaning. (See figure 5.)
Removing the Cutting Assembly:
Raise the Cutting Assembly to its most upright
position. Slide the release button to the right
and slide out the Cutting Assembly. To replace
the Lever hold it vertically with the release
button slid to the right, gently slide it into the
keyhole and rotate clockwise. (See figure 5.)
Drive Wheel:
Wipe with a damp cloth to thoroughly clean, use
a small brush to remove accumulated dirt.
Motor Housing:
Wipe over with a damp cloth.
Do not use harsh abrasives or cleaners to clean
any parts of your Open All, as these may scratch
the parts.
Do not wash any parts in an automatic
dishwasher, as the hot water temperatures and
harsh detergents may ultimately warp and
scratch these parts.
Warning: NEVER IMMERSE THE OPEN ALL IN
WATER OR ANY OTHER LIQUID.
Care and cleaning.
Sunbeam is a registered trademark. Open All is a
trademark of the Sunbeam Corporation. Made in China.
Due to minor changes in design or otherwise, the product
may differ from the one shown in this leaflet. Approved by
the appropriate Electrical Regulatory Authorities. Backed
by Sunbeam‘s 12 Month Replacement Guarantee and
National Service Network.
© Copyright. SUNBEAM CORPORATION LIMITED 2001.
(INCORPORATED IN N.S.W.) A.C.N. 000 006 771
For more information or advice on any Sunbeam products,
contact the Sunbeam Consumer Service Line on 1800 025 059
in Australia. In New Zealand - contact the Sunbeam Office in
Auckland on 09 912 0747.
Figure 5.
Drive wheel
Keyhole
Release button