Kenwood CO606 User manual

know your table top
can opener
Your Kenwood Can Opener can be
used to open a variety o domestic
can shapes and sizes. In addition the
CO606 incorporates a bottle opener
and a kni e sharpening acility.
before using your Kenwood
app iance
●Read these instructions care ully
and retain or uture re erence.
●Remove all packaging and any
labels.
sa ety
●Do not immerse appliance, cord or
plug in water or other liquid.
●Never use a damaged appliance.
Get it checked or repaired: see
‘service and customer care’.
●Unplug the appliance rom the
mains supply
●●be ore cleaning
●●immediately a ter use.
●This appliance is not intended or
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack o
experience and knowledge, unless
they have been given supervision or
instruction concerning use o the
appliance by a person responsible
or their sa ety.
●Children should be supervised to
ensure that they do not play with
the appliance.
●Only use the appliance or its
intended domestic use. Kenwood
will not accept any liability i the
appliance is subject to improper
use, or ailure to comply with these
instructions.
before p ugging in
●Make sure your electricity supply is
the same as the one shown on the
underside o your can opener.
Important – UK on y
●The wires in the cord are coloured
as ollows:
Blue = Neutral, Brown = Live.
●The appliance must be protected
by a 3A approved (BS1362) use.
Note:
●For non-rewireable plugs the use
cover MUST be re itted when
replacing the use. I the use cover
is lost then the plug must not be
used until a replacement can be
obtained. The correct use cover is
identi ied by colour and a
replacement may be obtained rom
your Kenwood Authorised Repairer
(see Service).
●I a non-rewireable plug is cut o it
must be DESTROYED
IMMEDIATELY. An electric shock
hazard may arise i an unwanted
non-rewireable plug is inadvertently
inserted into a 13A socket outlet.
●This appliance con orms to EC
directive 2004/108/EC on
Electromagnetic Compatibility and
EC regulation no. 1935/2004 o
27/10/2004 on materials intended
or contact with ood.
key
햲bottle opener
햳drive wheel
햴magnet
햵lever
햶cutter blade
햷guide pin
햸kni e sharpener
햹cord stowage
using your table top can
opener
1 Ensure that the lever is in position
with the magnet housing ully
located (Fig. 1 and 2).
2 Plug the appliance into the power
supply.
3 Li t the lever to the open position.
4 Hold the can with the top rim
resting under the metal guide pin
and the can resting on the drive
wheel (Fig. 3).
5 Press the lever lightly down to start
the motor. The sel -starting blade
will then pierce the can and
commence cutting.
6 The can will be held ixed in position
with the magnet resting against the
lid. Large or wide cans may require
extra support rom the user.
7 Once the can is open, the motor
will automatically stop, retaining the
can and lid sa ely in place.
8 To remove, li t the lever whilst
holding the can.
9 With the exception o aluminium
cans, the lid will be retained by the
magnet.
10For tidiness, any unwanted length
o cord can be stowed inside the
appliance.
using the bottle opener
When opening tall bottles, the unit
should be used towards the edge
o a work top.
1 Position the bottle with the cap
under the ront rim o the bottle
opener.
2 Push down the bottle to remove the
cap whilst steadying the unit with
one hand.
햲
햵
햷
햸
햹
햶
햳
햴
Fig. 1
Fig. 2
Fig. 3

CO606
using the kni e
sharpener
1 With the can opener sideways on,
place the kni e into one o the
recesses.
2 Press the lever down and gradually
draw it towards yoursel . Then
place the kni e in the other recess
and repeat. Take care not to allow
the kni e to cut into the body o the
can opener.
3 Repeat this cycle several times in
order to sharpen the kni e
satis actorily.
4 The grinding wheel may jam i too
much pressure is applied on the
kni e. Li t the kni e slightly to
release the wheel.
NOTE: Knives without a serrated
edge, pre erably carbon steel are
most suitable or sharpening.
care and cleaning
●Disconnect the appliance by
switching o and removing the
plug rom the power supply.
●Li t the lever ully and withdraw the
assembly rom the can opener.
●Wash the lever in hot sudsy water
and dry thoroughly. Dishwashing is
not advised.
●Replace the lever in the body
●Wipe over the body with a damp
cloth and dry thoroughly.
service & customer
care
●I the cord is damaged it must, or
sa ety reasons, be replaced by
KENWOOD or an authorised
KENWOOD repairer.
I you need help with:
●using your can opener or
●servicing or repairs (in or out o
guarantee)
콯call Kenwood customer care on
023 9239 2333. Have your
mode number ready - it's on
the underside o your can opener.
●spares and attachments
콯call 0870 2413653.
other countries
●Contact the shop where you
bought your can opener.
●Designed and engineered by
Kenwood in the UK.
●Made in China.
IMPORTANT INFORMATION FOR
CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE
WITH EC DIRECTIVE
2002/96/EC.
At the end o its working li e, the
product must not be disposed o as
urban waste.
It must be taken to a special local
authority di erentiated waste collection
centre or to a dealer providing this
service.
Disposing o a household appliance
separately avoids possible negative
consequences or the environment
and health deriving rom inappropriate
disposal and enables the constituent
materials to be recovered to obtain
signi icant savings in energy and
resources. As a reminder o the need
to dispose o household appliances
separately, the product is marked with
a crossed-out wheeled dustbin.
guarantee (UK on y)
I your can opener goes wrong
within one year rom the date you
bought it, we will repair or replace it
ree o charge provided:
●you have not misused, neglected or
damaged it;
●it has not been modi ied (unless by
Kenwood);
●it is not second-hand;
●it has not been used commercially;
●you have not itted a plug
incorrectly; and
●you supp y your receipt to
show when you bought it.
This guarantee does not a ect your
statutory rights.
Head O ice Address:
Kenwood Limited, New Lane, Havant, Hampshire PO9 2NH, UK
www.kenwoodworld.com
Designed and engineered by Kenwood in the UK
Made in China 85576/7