SunBriteTV SB-CM-T-L-BL User manual

1
SB-CM-T-L-BL / SB-CM-DT-L-BL
Weatherproof Ceiling Mount for Large TVs
Install Guide
We recommend this product be installed by a qualified professional. Do not install if you have doubts
regarding the eectiveness or safety of an installation method.
Product Details
Specifications Box Contents Tools Required
Maximum Load: 79.5 kg (175 lb) Ceiling plate assembly (1) Power drill
Extension: 0.91 m (3 ft.) Mounting head (1) 3/16" (5 mm) drill bit
Stainless steel hardware Adapter plate (1 or 2) 5/16" (8 mm) masonry bit
Pan/swivel range: 360° TV arms (2 or 4) 1/2" (13 mm) wrench
Tilt range: +0°/-20° 0.91 m (3 ft.) extension pole (1) Phillips-head screwdriver
Weather-resistant coating Hardware kit (see below) 3/8" socket wrench
VESA: 200×200 up to 700×500 7/16" socket wrench
Hardware Kit Contents
M6 × 12 mm Phillips-
head screw (×4/8)
M8 × 16 mm Phillips-
head screw (×4/8)
Hex wrench 2.5 mm,
security (×2)
Hex wrench,
4 mm (×1)
M4 ×
20 mm Phillips-
head screw (×4/8)
M5 × 30 mm Phillips-
head screw (×4/8)
M6 × 30 mm Phillips-
head screw (×4/8)
M8 × 20 mm Phillips-
head screw (×4/8)
M8 × 40 mm Phillips-
head screw (×4/8)
M8 carriage bolt (×4/8)
M8 nylon-insert
nut (×4/8)
M5 × 12 mm Phillips-
head screw (×4/8)
M6 × 20 mm Phillips-
head screw (×4/8)
Security wrench (×1)
M5 (16 × 5.3 × 1.5 mm)
metal washer (×4/8)
#14 × 2.5" lag screw (×4)
M8 (20.5 × 8.5 × 2 mm)
metal washer (×12/24)
Locking pin (×1/2)
M4/M5/M6 spacer:
12 mm (×4/8)
M6/M8 spacer:
17.8 mm (×4/8)
M5 × 5mm set screw,
security (×4)
M5 × 5 mm set screw (×4)
M4 × 12 mm Phillips-
head screw (×4/8)
M6 (17.8 × 6.5 × 1.5 mm)
metal washer (×4)

2
Warnings
Do not begin installation until you have thoroughly read and understood these instructions. Failure to comply with these
instructions could result in damage to the product, or serious injury, or death. The manufacturer does not accept responsibility for
incorrect installation.
Do not install if any parts are missing or defective. Do not attempt to replace with unapproved parts or materials or install
without all required parts.
Ensure the ceiling will safely support the combined weight of the mount and your chosen display. TV display should be removed
from mount in situations of high wind exceeding 97 kph (60 mph). Inspect all fasteners and the mounting plate’s attachment to
the ceiling for signs of loosening or damage after any strong wind event, and at least once annually. Tighten any loose fasteners.
If any damage is observed, remove the mount from service.
Installation
Warning: These ceiling mounts are designed for a maximum weight of 175 lbs / 79.5 kg.
Caution: Overtightening can damage the bolts and reduce their holding strength.
Mount the Ceiling Plate
Place the ceiling plate on the mounting surface and mark the
mounting hole locations.
Wood Joist
Drill four holes into the joist using a 3/16" drill bit. Be sure to
drill into the center of the joists.
Insert lag screws through the ceiling plate and tighten.
Concrete Ceiling
Caution: Before drilling, verify the concrete is at least 1-3/8" thick. Concrete must be 2000 psi density
minimum. Cinder block must meet ASTM C-90 specifications. Ensure you mount in a solid
part of the block, 1" minimum from the side of the block. Do not drill into mortar joints.
Caution: Use a standard electric drill on slow setting. Do not use a hammer drill to avoid breaking
out the back of the hole when entering a void or cavity.
Concrete anchors not provided. We recommend an outdoor-
rated 5/16" × 2 1/2" wedge or sleeve anchor for concrete.
Drill four holes into concrete using a 5/16" masonry bit. Insert
hex sleeve anchors, per instructions included with the anchors.
Remove washer and nut from the ends of all four anchors.
Align ceiling plate over the four concrete anchors.
Re-install washers and nuts onto the anchors and tighten until
secure, per instructions included with the anchors.
Wood
Concrete

3
Structural Steel Beam/Plate
Warning: Steel structure must be specified to support additional load of mount and TV.
Mounting hardware for this method not provided. 5/16" (or
M8 equivalent) diameter hardware of sucient length is
recommended. Bolts are recommended to be one of the
following:
Imperial: Grade 5 with a corrosion-resistant coating (zinc
plating or dip-spin coating) or stainless steel (ASTM F593)
Metric: Grade 8.8 with corrosion-resistant coating (zinc plating
or dip-spin coating) or M8 Property Class 70 or greater for
stainless steel (A2-70)
A flat washer should be used against the mounting plate slots,
and a nylon-insert lock nut is recommended
Drill four holes using a 3/8” bit through the steel plate.
Attach the Extension Pole
Thread the extension pole into the bracket. Screw it in, ensuring
the holes in the pole align with the holes in the bracket. Slide the
safety bolt through the bracket and pole, and secure it with a
nut. Insert and tighten the set screw.
Attach the Mount Head
Insert the bolts on the adapter plate through the angled
slots in mounting head (near right). Place M8 washers
and nylon-insert nuts on the ends of the bolts and tighten.
Screw the mount head onto the end of the extension pole
and tighten the set screws (far right).
Attach the TV Arms to the Display
Attach the TV arms to the display using M4, M5, M6, or
M8 screws. For displays with a hole pattern in a pocket or
inputs behind adapter plate, add spacers between the TV
arms and the display.
Steel

Attach the Display to the Ceiling Mount
Assembly
Hang the display on the wall arm assembly by the TV
arms, ensuring all three hooks slide into holes of mount
head.
Using a Phillips screwdriver, tighten locking screws at the
bottom of each TV arm, ensuring that the screws hold the
arms securely to the bracket (near right).
Insert locking pin (far right).
Adjustments
Warning: Completely loosening and/or removing nuts may cause plate and/or TV to fall.
Tilt Adjustment
Loosen screws on side of mount head (only enough to allow controlled adjustment), then adjust tilt
forward or backward.
Retighten screws, then make sure that the tilt angle is locked.
Horizontal Adjustment (Roll)
Slightly loosen all four nylon-insert nuts behind the adapter plate, to allow the plate to move.
Using the corners of the TV, adjust left/right until level. Re-tighten all nylon-insert nuts.
4
Technical Support
For technical support, please call 866-357-8688 or visit https://www.sunbritetv.com/support/services/contact-support, fill out the
support request form, and our support team will respond via email.
Visit tech.control4.com/technician for discussions, instructional videos, news, and more.
Warranty and Legal Notices
Find details of the product’s Limited Warranty and other resources such as regulatory notices and patent and safety information,
at snapone.com/legal or request a paper copy from Customer Service at 866.424.4489.
Copyright ©2022, Snap One, LLC. All rights reserved. Snap One and its respective logos are registered trademarks or
trademarks of Snap One, LLC, in the United States and/or other countries. Control4, SunBriteDS, and SunBriteTV are also
registered trademarks or trademarks of Snap One, LLC. Other names and brands may be claimed as the property of their
respective owners. Snap One makes no claim that the information contained herein covers all installation scenarios and contin-
gencies, or product use risks. Information within this specification subject to change without notice.
220308-1425
Part # 200-SB-CM-T-L-BL-001-C