SunBriteTV SB-WM46 User manual

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Outdoor Articulating Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
SB-WM46

SB-WM46 Installation Instructions
2
DISCLAIMER
SunBriteTV LLC (SBTV) intend to make this manual accurate
and complete. However, SBTV makes no claim that the
information contained herein covers all details, conditions or
variations, nor does it provide for every possible contingency in
connection with the installation or use of this product. The
information contained in this document is subject to change
without notice or obligation of any kind. SBTV makes no
representation of warranty, expressed or implied, regarding the
information contained herein. SBTV assumes no responsibility
for accuracy, completeness or sufficiency of the information
contained in this document.
SunBriteTV® is a registered trademark of SunBrite TV LLC.
Built to SunBriteTV® specifications by Chief Manufacturing. All
rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems/
accessories are properly assembled and installed using the
instructions provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the SB-WM46 up to (and
including) the display does not exceed 150 lbs (68 kg).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return themounting system to a service center for
examination and repair.
IMPORTANT ! : The SB-WM46 mounts are designed to be
mounted to a 2" x 4" wood studs (16" or 24" on center) wall with
a maximum covering of 5/8" thick drywall, plywood, OSB,
fiberboard, buffalo board or other similar sheathing materials.
IMPORTANT ! : The SB-WM46 mounts may be installed to a
bare 8" concrete wall if 5/16 x 3" Buildex® Tapcon® anchors
with Blue Climaseal® coating(not included) are used inplace of
lag bolts (X) provided.
--SAVE THESE INSTRUCTIONS--

Installation Instructions SB-WM46
3
DIMENSIONS
MAX EXTENSION
21.66
550.2
0.38
9.5
PADLOCK MAY BE ADDED FOR SECURITY
1/4" OR 5/16" DIAMETER SHANK
MAX TILT
15°
C
L
C
L
16.00
406.4
1.00
25.4

SB-WM46 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité

Installation Instructions SB-WM46
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
1/4” (6.4mm) - concrete
7/16” (11.1mm)
1/2” (12.7mm)
7/32” (5.5 mm) - wood studs
1/2" (12.7mm) -wood stud
3/8" (9.5mm) - concrete
9/16” (14.3mm)
5/32"
A (1)
B (2)
D (2)
H (1)
I (1)
J (1)
K (12) L (12) M (4) N (1) Q (1) R (8)
3/16"
7/32"
#8-32 x 3/8"
1/4" 1/4" 1/8" 5/16"
1/4" x 5/8"
T (1)
V (1)
[Locking pin]
[Main assembly]
[Faceplate bracket - short]
[Interface
[Locking bracket] X (4)
5/16” x 3 1/2” Z (1)
5/16”
F (1)
[Upper cover]
[Lower cover]
[Faceplate]
bracket - short]
Y (4)
AA (4)
M8 x 20mm
AB (4)
M8 x 30mm AC (4)
M6 x 16mm AD (4)
M6 x 25mm
AF (4)
M5 x 16mm AG (4)
M5 x 20mm AH (4)
M5 x 25mm AJ (4)
M4 x 16mm AK (4)
M4 x 20mm
AE (4)
M4 x 25mm
AL (4) AM (4) AN (4)
6.40mm AP (4)
12.7mm
G (1)
5/16 x 3" Buildex Tapcon® anchors
(not included)
with Blue Climaseal® coating
E (2)
[Interface
bracket - long]
C (2)
[Faceplate bracket - long]
P (4)
[Backing plate]
W (4)
[Cable cover]
Hardware bag
#10 1/4"

SB-WM46 Installation Instructions
6
ASSEMBLY and INSTALLATION
Install Arm Assembly/Wall Plate to Wall
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
IMPORTANT ! : The SB-WM46 mounts are designed to be
mounted to a 2" x 4" wood studs (16" or 24" on center) wall with
a maximum covering of 5/8" thick drywall, plywood, OSB,
fiberboard, buffalo board or other similar sheathing materials.
IMPORTANT ! : The SB-WM46 mounts may be installed to a
bare 8" concrete wall if 5/16 x 3" Buildex® Tapcon® anchors
with Blue Climaseal® coating(not included) are usedin place of
lag bolts (X) provided.
Wood Studs Installation
1. Level arm assembly/wall plate (A) and mark locations of
pilot holes. (See Figure 1)
2. Drill four 7/32" pilot holes at marked locations.
3. Install four 5/16 x 3 1/2” lag screws (X) through four flat
washers (Y),arm assembly/wall plate (A), into drilled holes.
(See Figure 1)
Figure 1
Concrete Installation
1. Level arm assembly/wall plate (A) and mark locations of
pilot holes. (See Figure 2)
2. Drillfour 1/4"pilot holes atmarked locations. (SeeFigure 2)
3. Install four Buildex® Tapcon® anchors through four flat
washers (Y),arm assembly/wall plate (A), into drilled holes.
(See Figure 2)
Figure 2
Cover Installation
1. Install upper and lower covers (F and G) onto main
assembly (A) mounting rails. (See Figure 3)
Figure 3
(Y) x 4 (A)
3
1
x 4
2
x 4
(X) x 4
7/32"
(wood studs installation)
(Y) x 4
(A)
3
1 x 4
2
x 4
Buildex® Tapcon® anchors x 4
1/4"
(concrete installation)
(G)
(F)
(A)

Installation Instructions SB-WM46
7
Installing Interface Brackets to Display
1. Place display face down on a soft, non-abrasive surface.
2. (If applicable) Remove four sets of bolts and washers that
were shipped attached to the back of the display. (See
Figure 4)
Figure 4
3. Place two interface brackets (D or E) on the back of the
display, with the indented brackets facing toward the inside
of the television. (See Figure 5) or (See Figure 6)
NOTE: Use short brackets (D) if installingto 46" or55" models
and long interface brackets (E) if installing to 65"
models. (See Figure 5) or (See Figure 6)
NOTE: Spacers (AL and AM) are used to offset the bracket if
the mounting holes are recessed or to get around the
protrusions.
4. Securethe interface brackets (D or E) to the display. Select
the mounting hardware that fits your application. (See
Figure 5) or (See Figure 6)
•Use spacers (AL and AM), if necessary.
•Use M6 screws (AC or AD) or M8 screws (AA and AB)
and 1/4" washers (AP).
•Or, use M4 screws (AE, AJ or AK) or M5 screws (AF,
AG or AH), 1/4" washers (AP) and #10 washers (AN).
Figure 5
Figure 6
Install Faceplate Brackets to Faceplate
1. Alignfaceplatebrackets(Bor C)withfaceplate(Z)andslide
into position. (See Figure 7)
NOTE: Use short faceplate brackets (B) if installing to 46" or
55" models and long faceplate brackets (C)if installing
to 65" models. (See Figure 7)
Figure 7
2
x 4
4
(AA-AK) x 4
(AL or AM) x 4
(if necessary)
(D) x 2
(46" or 55" models)
(AN) x 4
(w/M4 and M5
screws ONLY)
(AP) x 4
4
(AA-AK) x 4
(AN) x 4
(AL or AM) x 4
(if necessary)
(w/M4 and M5
screws ONLY)
(AP) x 4
(E) x 2
(65" models)
1
(B) x 2
(Z)
1
(Z)
(C) x 2
(46" or 55" models) (65" models)

SB-WM46 Installation Instructions
8
2. Using 5/32” hex key (H), install four 1/4 x 5/8” button head
cap screws(K) through four 1/4” washers (L), faceplate (Z),
faceplate brackets (B or C), into four 1/4” nuts (M). Tighten
securely. (See Figure 8)
Figure 8
Install Faceplate to Display
1. Align faceplate brackets (B or C) with interface brackets (D
or E), aligning the center of display with the faceplate bolt.
(See Figure 9) and (See Figure 10)
Figure 9
2. Using 5/32" hex key (H), install eight 1/4 x 5/8” screws (K)
through eight 1/4” washers (L) andfaceplatebrackets (B or
C) into four backing plates (P). Tighten securely. (See
Figure 10)
2
(M) x 4
(K) x 4
2
7/16” (11.1mm)
(L) x 4
(short interface models shown)
faceplate bolt
1
(short interface models shown)
Figure 10
(P) x 4
(L) x 8
(K) x 8
2
1
(B or C) x 2
(short interface models shown)

Installation Instructions SB-WM46
9
Display Installation
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the SB-WM46 up to (and
including) the display does not exceed 150 lbs (68 kg).
1. Align slots on upper portion of faceplate (E) with tabs on
upperportionofarmassembly(A).Lowerdisplayintoplace,
pivoting threaded stud on faceplate (E) into slot on arm
assembly (A). (See Figure 11)
2. Install spacer (N), locking bracket (T), and nut (Q) onto
threaded stud. Tighten securely. (See Figure 11)
Figure 11
3. (Optional) Install padlock through locking bracket (T). (See
Figure 12)
NOTE: Padlock should have a shackle diameter of 1/4" or
5/16" and a clearance height of 1".
Figure 12
Cable Management
CAUTION: Ensure that adequate cable slack exists for
movement of display, and that cables will not be pinched by
installation of covers (W) or screws (R).
1. Carefullyinsertcablesintocavitieslocatedin lowerportions
of mount arms. (See Figure 13)
2. Install each cover (W) with two screws (R). (See Figure 13)
Figure 13
3. Use cable ties (notincluded) to secure cables to wallmount
at cable slot locations. (See Figure 14)
Figure 14
1
2
1/2” (12.7mm)
(N)
(T)
(E)
(A)
(Q)
(short interface models
shown)
(T)
3
(R) x 8
1
2
(W) x 4
(W)

SB-WM46 Installation Instructions
10
Adjustments
Pitch
1. Loosen pitch adjustment knob. (See Figure 15)
2. Tilt display to desired angle (-15° to +15°). (See Figure 15)
3. Tighten pitch adjustment knob. (See Figure 15)
Figure 15
Roll
1. Roll position may be adjusted 2.5° in either direction. (See
Figure 16)
Figure 16
Extension and Swivel Tension
WARNING: Excessive loosening or tightening of
adjustment screws can result in serious personal injury or
damage to equipment!
1. Using hex keys (I, J), loosen or tighten adjustment screws
as required to achieve desired tension. (See Figure 17)
Figure 17
1
-15°
0°
+15°
2
3
1
(short interface models shown)
9/16” (14.3mm)
1
1
(short interface models shown)

Installation Instructions SB-WM46
11
Locking in Collapsed Position
The SB-WM46 may belocked in the collapsed position byusing
the locking pin (V).
1. Insert locking pin (V) through lower bracket on main
assembly (A) and into holes on brackets behind faceplate.
(See Figure 18) and (See Figure 19)
Figure 18
Figure 19
1
2
(V)
(A)
(short interface models shown)
(V) in locked position
(faceplate hidden for clarity)
2
(short interface models shown)

SB-WM46 Installation Instructions
8800-002947 Rev02
04/17
SunBriteTV, LLC
2001 Anchor Court
Thousand Oaks, CA 91320
866-357-8688
www.sunbritetv.com