SunBriteTV SB-WM-F-L-BL User manual

INSTALLATION MANUAL
SB-WM-F-L-BL / SB-WM-T-L-BL
Weatherproof Universal Fixed and Tilt Mounts
For Large Displays

pg.2
Installation Manual
© 2017 SunBrite
WARNINGS:
• Installation by a qualied professional is highly recommended for this product.
• Do not begin installation until you have thoroughly read and understand these instructions.
• This mount ts displays up to VESA 700mm x 500mm and supports a maximum load of 165 lbs (75 kg).
• Ensure the mounting wall will safely support four times the combined weight of the mount and display panel.
• The manufacturer does not accept responsibility for incorrect installation.
SPECIFICATIONS: TOOLS REQUIRED:
• Power Drill
• 5/16” and 1/4” Drill Bit
• Phillips Head Screw Driver
• Level
BOX CONTENTS:
• Wall Plate (1)
• Arm left (1)
• Arm right (1)
• Maximum Load: 165 lbs. (75 kg)
• Forward Tilt Range: - 8° /+ 13°
• Horizontal Tilt Range: +5°
•Weather Resistant Coating
• Stainless Steel Mounting Hardware • Socket Wrench
with 1/2” Socket head
CAUTION:
This wall mount is intended for use only with the maximum weight of 165 lbs (75kg).
HARDWARE KIT
Bag 2
PACKAGE CONTENTS: Arms
(With Tilt)
Wall Plate
Arms
(With Fixed)
Bag 3
Bag 1
Bag 4
Bag 5
Bag 6
Bag 7
(W) Concrete Anchor (x6)
(U) M8x63
Lag Bolt (x6)
(V) Lag Bolt
Washer (x6)
(S) M5 Washer (x16) (T) M8 Washer (x8)
(A) M4x10 Bolt (x4) (B) M4x20 Bolt (x4) (C) M4x30 Bolt (x4) (D) M4x40 Bolt (x4)
(E) M5x10 Bolt (x4) (G) M5x30 Bolt (x4) (H) M5x40 Bolt (x4)(F) M5x20 Bolt (x4)
(I) M6x10 Bolt (x4) (J) M6x20 Bolt (x4) (K) M6x30 Bolt (x4) (L) M6x40 Bolt (x4)
(M) M8x10 Bolt (x4) (N) M8x20 Bolt (x4) (O) M8x30 Bolt (x4) (P) M8x40 Bolt (x4)
(Q) M4/M5
Nylon Spacer (x8)
(R) M6/M8
Nylon Spacer (x8)
Allen
Key (x1)

Installation Manual
pg.3
INSTALLATION:
Step 1: Mount the Wall Bracket Assembly
For Mounting on a Stud Wall
a. Pre-drill holes into two wood studs using a 1/4” drill bit.
Be sure to drill into the center of the studs at least
2-1/2” deep. The use of a stud nder is highly
recommended.
b. Insert four Lag Bolts (U) into holes through the Wall
Plate and tighten down. (Figure 1)
WARNING: Tighten bolts so that wall plate is rmly
attached, but do not overtighten. Overtightening
can damage the bolts, greatly reducing their
holding strength.
For Mounting on a Concrete Wall
a. Pre-drill holes into concrete using 5/16” drill bits to a
depth of 2 1/2”. Insert concrete wall anchors (W)
and tap in with hammer, if necessary (Figures 2 & 3).
WARNING: When installing wall arm assembly on
cinder block, verify rst that you have a minimum
of 1-3/8” of concrete thickness to be used for the
concrete anchors. Do not drill into mortar joints! Be
sure to mount in a solid part of the block, generally
1”minimum from the side of the block. Cinder block
must meet ASTM C-90 specications. It is suggested that
a standard electric drill on slow setting is used to drill the
hole instead of a hammer drill to avoid breaking out the
back of the hole when entering a void or cavity.
Concrete must be 2000 psi density minimum.
Lighter density concrete may not hold concrete
anchor.
Make sure that the supporting surface will safely
support the combined load of the equipment and
all attached hardware and components.
b. Insert four Lag Bolts (U) into the wall anchors (W)
through the Wall Plate. Tighten all bolts.
WARNING: Tighten bolts so that wall plate is rmly
attached, but do not overtighten. Overtightening
can damage the bolts, greatly reducing their
holding strength.
Step 2: Mount Arms to TV
a. Determine the diameter of the screw (parts A through
P) your TV requires by carefully trying to hand-thread
one into the threaded insert on the rear of the TV. If
there is any resistance, stop immediately.
b. Thread the screw through the washer (Q or R), arm,
spacer (S or T), and into the TV.
Note: Spacers are commonly needed on TVs with
curved backs or recessed screw inserts.
c. Ensure the arms are installed at side to TV
and are square to each other after all screws have
been installed (Figure 4).
Correct
concrete
concrete
plaster/
drywall
plaster/
drywall
Incorrect
Cutaway View
Figure 2
Drill holes and
insert anchors.
Place wall arm
assembly plate
over anchor and
secure with
lag bolt.
Tighten all
lag bolts.
Wall Arm
Concrete
Wall
Lag Bolt
Figure 3
TIP: To assist in
installation, the
wall bracket features
a screw slot for
temporary hanging
of the bracket.
Figure 1
Figure 4
Bolts
Bolts
Center of Studs

Step 3: Hang TV on to the Wall Plate
a. Carefully lift the TV to hook the arms over the
top lip of the wall plate. Allow the lower portion of the
arms to swivel in under the bottom lip of the wall plate.
Do not release the TV until it is completely
connected to the wall plate.
Adjustments:
Adjust Horizontal Level and Tilt
Forward Tilt Adjustment (SB-WM-T-L-BL)
a. Using the included long Allen key, loosen the tilt adjustment
locks on the sides of the arms enough to allow movement.
b. Set the tilt to the desired angle, then re-tighten the locks. If
the locks cannot be tightened enough, remove the TV from
the wall for better access.
Horizontal Adjustment
a. If display is not horizontally level when mounted, Tilt
Adjustment Screws are included at the top of each arm
for micro-adjustments (Figure 7). Use provided
Allen Key to raise or lower the screw, which will in
turn raise or lower the mount.
Note: Due to display weight, it may be easier to lift panel
slightly when adjusting the screw. Caution should be taken
to avoid any slips or drops to avoid damage and/or injuries.
Locking
a. To lock the arms to the wall bracket, twist the locking tabs
until the edge catches behind the bracket. The Allen Key
can be used as a tool to help with this step. Padlock is
optional (not included).
Tilt Adjustment Lock
±5° Horizontal
Adjustment
Tilt Adjustment
Screw
Locking
Tab
Figure 5
Figure 6
Figure 7
Lifetime Limited Warranty
SunbriteTV™ Mounts have a Lifetime Limited Warranty. This warranty includes parts and labor repairs on all com-
ponents found to be defective in material or workmanship under normal conditions of use. This warranty shall
not apply to products which have been abused, modied or disassembled. Products to be repaired under this
warranty must be returned to SunbriteTV or a designated service center with prior notication and an assigned
return authorization (RA) number.
Technical Support 866.838.5052
170315-0816