Sunde H4S User manual

USER MANUAL FOR NETPOINT2.2 AND H4S 4
1
SUNDE
User’s Manual
for
NetPoint2.2 & H4S

USER MANUAL FOR NETPOINT2.2 AND H4S 4
2
©2015 Bigpond Technology. All rights reserved. www.sunde.net.pk
THANK YOU FOR PURCHASING SUNDE NETWORK TERMINAL. PLEASE READ THIS MANUAL
CAREFULLY BEFORE USE.
NOTE: All the information contained herein is the property of BIGPOND TECHNOLOGY. No part
of this publication (whether in hardcopy or electronic form) may be reproduced or transmitted,
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written consent of BIGPOND TECHNOLOGY. The software described in this
document is furnished under license and may only be used or copied in accordance with the
terms of such license.
This publication and the information herein is furnished AS IS, is subject to change without
notice, and should not be construed as a commitment by BIGPOND TECHNOLOGY. BIGPOND
TECHNOLOGY assumes no responsibility or liability for any errors or inaccuracies, makes no
warranty of any kind (express, implied, or statutory) with respect to this publication, and
expressly disclaims any and all warranties of merchantability, fitness for particular purposes, and
no infringement of third party rights.
Any references to company names in sample templates are for demonstration purposes only
and are not intended to refer to any actual organization.
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation
in the United States and other countries. All other trademarks are the property of their
respective owners.
If this guide is distributed with software that includes an end user agreement, this guide, as well
as the software described in it, is furnished under license and may be used or copied only in
accordance with the terms of such license. Except as permitted by any such license, no part of
this guide may be reproduced, stored in a retrieval system, or transmitted, in any form or by any
means, electronic, mechanical, recording, or otherwise, without the prior written permission of
BIGPOND TECHNOLOGY. Please note that the content in this guide is protected under copyright
law even if it is not distributed with
software that includes an end user license agreement.
The content of this guide is furnished for informational use only. It is subject to change without
notice, and should not be construed as a commitment by BIGPOND TECHNOLOGY. BIGPOND
TECHNOLOGY assumes no responsibility or liability for any errors or inaccuracies that may
appear in the informational content continued in this guide. USER MANUAL FOR NETPOINT2.2
AND H4S 3

USER MANUAL FOR NETPOINT2.2 AND H4S 4
3
Contents
1. Introduction
............................................................................................................................................. 4
1.1 Components
...................................................................................................................................... 5
1.2 Recommended Server Configuration
............................................................................................... 5
1.3 Connecting
....................................................................................................................................... 5
2. Software Installing
.................................................................................................................................. 7
2.1 Installing NetPoint2.2 Software
........................................................................................................ 7
2.2 Enabling Remote Desktop
.............................................................................................................. 13
2.3 Uninstalling NetPoint2.2 Software
................................................................................................. 14
3. Setting up H4S
........................................................................................................................................ 16
3.1 Setting H4S IP Address
.................................................................................................................... 16
3.2 Setting Server IP Address
................................................................................................................ 19
3.3 Setting Screen Resolution
............................................................................................................... 21
3.4 Auto Logon
...................................................................................................................................... 23
3.5 Advanced Settings
.......................................................................................................................... 25
4. Functions of NetPoint2.2 Management Console
.................................................................................. 28
4.1 Terminal Information
...................................................................................................................... 28
4.2 Monitoring
..................................................................................................................................... 28
4.3 Send Message
................................................................................................................................ 29
4.4 User Accounts
................................................................................................................................. 30
4.5 One-Key Broadcasting
.................................................................................................................... 33
5. H4S Connecting to Windows or Linux Without NetPoint2.2
................................................................ 34
5.1 How to Mount USB flash drive in Linux
........................................................................................ 35 USER MANUAL FOR NETPOINT2.2 AND H4S 4

USER MANUAL FOR NETPOINT2.2 AND H4S 4
4
1. Introduction
SUNDE H4S Network Terminal is based on SOC with NetPoint2.2 tm software. It is designed to work
in client-server networks and depends primarily on the central server for data processing. Its main job
is to convey input and output between the user and the remote server.By using SUNDE H4S Network
Terminal devices, a great deal hardware cost can be saved, much less software support is required,
much less power is consumed, little desk space is occupied, and much less e-waste is generated.
Based on RDP, H4S has its unique Speed-Up technologywhich enables it to deliversmooth HD movie
playback on end user’s desktop.

USER MANUAL FOR NETPOINT2.2 AND H4S 4
5
1.1 Components
You can find the following items in the color box of the device:
1. H4S
2. Power Supply Adapter
Please check to see if any part is missing or physically damaged. Contact the dealer immediately if
anything is missing or damaged. Save the packaging for future use.
For connecting H4S to the host (PC/Server), the following are essential:
1. An Ethernet RJ45 LAN port on the Host PC.
2. An Ethernet RJ45 cable of suitable length.
3. Ethernet switch or router is required to connect more than one Network Terminal or other network
devices. Additional Ethernet cables will be required in this case.
1.2 Recommended Server Configuration
You can find a detailed Server Configuration chart in H4S datasheet. Remember, the size chart is
reference only. Since the workload may vary greatly in different environments, a test running is
suggested if you need a more accurate server configuration data.
H4S Front
H4S Back

USER MANUAL FOR NETPOINT2.2 AND H4S 4
6
1.3 Connecting
STEP 1. Connect your Keyboard/Mouse/Monitor/Speaker or Headphone as shown in the picture:
STEP 2. Connect the Terminal to Host PC/Switch/Router using the Ethernet cable with RJ45 pins as
shown below.
CAUTION
USE ONLY THE ORIGINAL POWER
SUPPLY ADAPTER
STEP 3. Connect the power adapter.

USER MANUAL FOR NETPOINT2.2 AND H4S 4
7
2. Software Installing
2.1 Installing NetPoint2.2 Software
Prior to installing NetPoint2.2, please make sure to DISABLE or UNINSTALL any AntiVirus or
Firewall software that may be running in the background. Some Security software may
interfere with the installation and operation of NetPoint2.2. They can be enabled or reinstalled
after the installation of NetPoint2.2.
Please visit http://www.sunde.net.pk/ for the latest version of NetPoint2.2.
Find the location where you put “NetPoint Installation Package2”. In the example picture, it is put on
the desktop of the host OS. Double click on it to run the installation.

USER MANUAL FOR NETPOINT2.2 AND H4S 4
8
If below message pops up, choose “Yes” to continue:
Click on “Next” to continue:
Choose “I accept the terms of the license agreement”:

USER MANUAL FOR NETPOINT2.2 AND H4S 4
9
Choose the installation location. Use the default destination folder. Click on “Next” to continue:

USER MANUAL FOR NETPOINT2.2 AND H4S 4
10
Keep the default. Then “Next”:
Now the software is installing:

USER MANUAL FOR NETPOINT2.2 AND H4S 4
11
When this warning shows up, choose “Install this driver software anyway”:
Installing virtual audio device:

USER MANUAL FOR NETPOINT2.2 AND H4S 4
12
Installation is complete. Click “Finish” to restart the system:

USER MANUAL FOR NETPOINT2.2 AND H4S 4
13
2.2 Enabling Remote Desktop
We need to set the system to allow Remote Desktop so that SUNDE terminal can log on the
system remotely. Take Windows 7 as the example:
Go to “Computer”, then “System properties”.
In the new window, click on Remote, then choose “Allow connections from computers running
any version of Remote Desktop”. Click on “OK” to save.

USER MANUAL FOR NETPOINT2.2 AND H4S 4
14
2.3 Uninstall NetPoint2.2 Software
Click on the “NetPoint Installation Package2”:
Choose "Remove”
and then click on “Next” to continue:

USER MANUAL FOR NETPOINT2.2 AND H4S 4
15
When this pop up, choose “OK” to confirm uninstall:
When uninstall process is finished, click on “Finish” to restart the system:

USER MANUAL FOR NETPOINT2.2 AND H4S 4
16
3. Setting up H4S
There are two kinds of IP addresses need to be set. One is terminal’s Local IP, the
other one is Server’s IP.
3.1 Setting H4S IP Address
GET DYNAMIC IP ADDRESS FROM DHCP SERVER
"Dynamic Host Configuration Protocol” (DHCP) is an IP standard designed to reduce the complexity
of administering IP address configurations. A DHCP server would be set up with the appropriate
settings for a given network. Such settings would include a set of fundamental parameters such as
the gateway, DNS, subnet masks, and a range of IP addresses. Using DHCP on a network means
administrators need not configure these settings individually for each client on the network. The
DHCP would automatically distribute them to the clients. When the network terminal is connected to
a Network having a DHCP server, the settings for the Terminals would be as follows.
Click “Setup”, select “Local” tab, and choose “Use Dynamic IP Address”. Click “Save” to exit:

USER MANUAL FOR NETPOINT2.2 AND H4S 4
17
Then H4S will obtain an IP address from DHCP server, and when this is successful, it will search
over the network for available Servers. Results will be shown in the “Host List
USE STATIC IP ADDRESS FOR THE TERMINAL
This would be an option exercised by users with no DHCP server environment. In a small office
environment using less than 10 Terminals, this option would be more convenient.
Turn on the Network terminal.
Click the “Setup” In the “Local IP” ” tab, check “Use Static IP Address”.
1. IP Address: Give H4S an IP address of its own here. The easy way to do is to give it an IP
address after adding 1 to the last number of IP address you gave to the Host PC. Then you can
continue adding 2, 3... as you add more Terminals to the network. Each Terminal must have a
Unique IP address.
2. Subnet Mask: For a C type IP address, normally it will be 255.255.255.0.
USER MANUAL FOR NETPOINT2.2 AND H4S 18

USER MANUAL FOR NETPOINT2.2 AND H4S 4
18
3. Gateway: Most often, this is the IP address of your Router.

USER MANUAL FOR NETPOINT2.2 AND H4S 4
19
3.2 Setting Server’s IP Address
There are two ways to setup the server’s IP address.
SEARCH SERVERS IN LAN
If the server is in the same subnet with the terminal, the terminal can search the network and find the
server itself by set the server IP as “Search servers in LAN”.
After save the settings, H4S will go back to “Host List” page, and then display all available servers
(with NetPoint2.2) installed in the LAN.

USER MANUAL FOR NETPOINT2.2 AND H4S 4
20
Now you can choose the right Host Server from the list and then click “Connect” button to connect.
USE
STATIC IP FOR SERVER
You can setup the server using static IP address so that the terminal can logon the server directly
after power on. For those Host servers that are not in the same subnet as H4S, you have to setup
the IP address for the server in this way.
Please be aware that, if you are connecting a H4S to a Host with NetPoint2.2, only the IP
address of the host need to be supplied. If you are using the H4S to connect a Host without
NetPoint2.2, the IP address plus RDP port (3389 by default) have to be typed in (see chapter
5).