Cisco 2515-RF - 2515 Router User manual

About This Guide xv
About This Guide
This section discusses the objectives, audience, organization, and conventions of this
hardware installation and configuration guide.
Objectives
This publication will step you through the initial site preparation and installation of the
router. Troubleshooting, maintenance procedures, and cable specifications are also
provided.
Although minimum software configuration information is provided, it is not meant as
comprehensive router configuration instructions. For detailed software configuration
information, refer to the Cisco IOS configuration guide and command reference
publications. These publications are available on the documentation CD that came with
your router or you can order printed copies. Refer to the “Ordering Documentation” section
in the “Overview of the Router” chapter for ordering information.
This publication describes a variety of router models that are similar in functionality, but
differ in the number of interfaces supported. Some information provided may not apply to
your particular router model.
AudienceThispublicationisdesignedforthepersoninstallingtherouter,whoshouldbefamiliarwith
electronic circuitry and wiring practices and have experience as an electronic or
electromechanical technician.

xvi Router Installation and Configuration Guide
Organization
Organization
The major sections of this hardware installation and configuration guide are as follows:
•Chapter 1, “Overview of the Router,” discusses the features and specifications of the
routers, and describes how to obtain technical support and order documentation.
•Chapter 2, “Preparing to Install the Router,” discusses environmental requirements,
safety recommendations, and describes the various ports and how to prepare for
connections between networks and ports.
•Chapter 3, “Installing the Router,” includes basic installation information and discusses
making connections to your LAN, WAN, and console terminal.
•Chapter 4, “Configuring the Router,” discusses how to configure your router using the
prompt-driven System Configuration Dialog, configuration mode, or AutoInstall. This
chapter also provides some basic information about how to use the Cisco IOS software.
•Appendix A, “Troubleshooting the Router,” discusses how to isolate problems and read
the LEDs.
•Appendix B, “Maintaining the Router,” discusses selected maintenance procedures.
•Appendix C, “Cable Specifications,” provides pinouts for the router ports and cables.
Conventions
This publication uses the following conventions to convey instructions and information.
Command descriptions use these conventions:
•Commands and keywords are in boldface font.
•Variables for which you supply values are in italic font.
•Elements in square brackets ([ ]) are optional.
•Alternative but required keywords are grouped in braces ({ }) and are separated by
vertical bars ( | ).

About This Guide xvii
Conventions
Examples use these conventions:
•Terminal sessions and information the system displays are in screen font.
•Information you enter is in boldface screen font.
•Nonprinting characters are in angle brackets (< >).
•Default responses to system prompts are in square brackets ([ ]).
Note Meansreader takenote. Notes contain helpful suggestions orreferences to materials
not contained in this manual.
Timesaver Means the described action saves time. You can save time by performing the
action described in the paragraph.
Caution Means reader be careful. In this situation, you might do something that could
result in equipment damage or loss of data.
Warning This warning symbol means danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, you must be aware of the hazards
involved with electrical circuitry and familiar with standard practices for preventing
accidents. (To see translated versions of this warning, refer to the Regulatory Compliance
and Safety Information document that accompanied your router.)

xviii Router Installation and Configuration Guide
Conventions

CHAPTER
Overview of the Router 1-1
1
Overview of the Router
Table 1-1 lists the router models discussed in this publication and provides a summary of
the interfaces supported on each model. These router models are similar in functionality,
but differ in the number of interfaces supported.
1. AUI = attachment unit interface.
2. ISDN = Integrated Services Digital Network.
3. BRI = Basic Rate Interface.
4. A CPA2515 model is not available.
Table 1-1 Summary of Router Interfaces
Model Ethernet AUI1(DB-15) Token Ring
(DB-9) Serial (DB-60) ISDN2BRI3 (RJ-45)
Cisco 2501/
CPA2501 1–2–
Cisco 2502/
CPA2502 –12–
Cisco 2503/
CPA2503 1–21
Cisco 2504/
CPA2504 –121
Cisco 2513/
CPA2513 112–
Cisco 2514/
CPA2514 2–2–
Cisco 25154–22–

1-2 Router Installation and Configuration Guide
Hardware Features
Note Throughout the remainder of the publication, one model number will be used in text
references. For example, references to the model 2501 router will apply to both the
Cisco 2501 and CPA2501 routers.
Hardware Features
In addition to the interfaces listed in Table 1-1, the routers include the following hardware
features:
•Dynamic random-access memory (DRAM) for main memory and shared memory
•Nonvolatile random-access memory (NVRAM) for storing configuration information
•Flash memory for running the Cisco IOS software
•EIA/TIA-232 console port for local system access using a console terminal
•EIA/TIA-232 auxiliary port for remote system access using a modem
Note EIA/TIA-232 and EIA/TIA-449 were known as recommended standards RS-232
and RS-449 before their acceptance as standards by the Electronic Industries Association
(EIA) and Telecommunications Industry Association (TIA).
Figure 1-1 to Figure 1-7 show the rear panels of the router models discussed in this
publication.

Overview of the Router 1-3
Hardware Features
Figure 1-1 Model 2501 Router Rear Panel
Figure 1-2 Model 2502 Router Rear Panel
H4262
Ethernet
AUI LED
Ethernet
AUI port
(DB-15)
Console
port (RJ-45)
Auxiliary port
(RJ-45)
On/off
switch Power
Synchronous
serial LEDs
Synchronous
serial ports
(DB-60)
System
OK LED
H6585
Token Ring
port (DB-9) Console
port (RJ-45)
Auxiliary port
(RJ-45)
On/off
switch PowerSynchronous
serial ports
(DB-60)
Token Ring
LED Synchronous
serial LEDs System
OK LED

1-4 Router Installation and Configuration Guide
Hardware Features
Figure 1-3 Model 2503 Router Rear Panel
Figure 1-4 Model 2504 Router Rear Panel
H6586
Ethernet
AUI port
(DB-15)
PowerSynchronous
serial ports
(DB-60)
Console
port
(RJ-45)
ISDN
BRI port
(RJ-45)
Auxiliary port
(RJ-45)
Ethernet
AUI LED Synchronous
serial LEDs ISDN
BRI LED System
OK LED
On/off
switch
Power
On/off
switch
H6587
Token Ring
port (DB-9) Synchronous serial ports
(DB-60)
Token Ring
LED Synchronous
serial LEDs System
OK LED
ISDN
BRI LED
Console
port
(RJ-45)
ISDN
BRI port
(RJ-45)
Auxiliary port
(RJ-45)

Overview of the Router 1-5
Hardware Features
Figure 1-5 Model 2513 Router Rear Panel
Figure 1-6 Model 2514 Router Rear Panel
H6588
TOKEN RING
Token Ring
port (DB-9) Ethernet AUI port
(DB-15)
Synchronous
serial ports
(DB-60)
Token Ring
LED
Power
On/off
switch
Ethernet
AUI LED Synchronous
serial LEDs System
OK LED
Console port
(RJ-45)
Auxiliary port
(RJ-45)
Synchronous
serial ports
(DB-60)
On/off
switch Power
H6589
Ethernet
AUI ports
(DB-15)
Ethernet
AUI LEDs Synchronous
serial LEDs System
OK LED
Console
port (RJ-45)
Auxiliary port
(RJ-45)

1-6 Router Installation and Configuration Guide
System Specifications
Figure 1-7 Model 2515 Router Rear Panel
System Specifications
The system specifications of the routers are listed in Table 1-2.
Table 1-2 System Specifications
Description Specification
Dimensions (H x W x D) 1.75 x 17.5 x 10.56 in. (4.44 x 44.45 x 26.82 cm),
one rack unit
Weight 10 lb (4.5 kg)
Input voltage, AC power supply
Current
Frequency
Power dissipation
100 to 240 VAC
1.2 to 0.6A
50/60 Hz
40W (maximum), 135.5 Btus1/hr
Input voltage, DC power supply
Current
Power dissipation
40W, 40 to 72 VDC
1.5 to 1.0A
40W (maximum), 135.5 Btus/hr
Processor 20-MHz Motorola 68EC030
On/off
switch Power
H6590
System
OK LED
Token Ring
LEDs Synchronous
serial LEDs
Synchronous
serial ports
(DB-60)
Token Ring
ports (DB-9) Console
port (RJ-45)
Auxiliary port
(RJ-45)