SunEarth MTG-LSR-52-19 User manual

Landscape Rack Installation Instructions
MTG-LSR-42-__ & MTG-LSR-52-__
ank you for purchasing the SunEarth Landscape Rack. e use of all stainless steel hardware and 6063-T6 structural aluminum
makes the SunEarth Landscape Rack a simple, strong, and durable solution for your landscape or sawtooth racking needs.
Package Contents:
2 EA Support Strut 42” or 52” Length, (Black Anodized pictured)
2 EA Rear Leg, 2” x 2” C Channel
2 EA Front Foot, 2” x 2” C-Channel, 4” Length
2 EA Rear Foot, 1 1/2” C-Channel, 4” Length
4 EA C-SSN (collector clip, 3/8” x 1” stainless steel bolt, 2 x washers, 1 x lock washer, 1 x nut)
6 EA Bolt Assembly (5/16” x 2 1/2” stainless steel bolt, 2 x washers, 1 x lock washer, and 1 x nut)
Suggested Installation Steps
Determine Front Feet positions and securely fasten Front Feet to mounting surface using
an acceptable fastening method for the mounting surface and your local conditions.
Insert Support Strut into Front Foot, insert bolt, and tighten nut. Make sure not to over
tighten. SunEarth recommends tightening the nut approximately 1/2 turn past the setting of
the lock washer or torque of 12 lbs. Repeat for remaining Support Strut.
Step 1
Step 2
www.sunearthinc.com
1
2
3
4
5
6
1
2
3
4
5
6
3

Note: In situations where the rack is to be mounted other than parallel to the roof line, cross bracing may be necessary.
If you have any questions or feedback, please feel free to email us at sales&suppor[email protected].
Complete Installation
Tilt the collector up, position the Back Legs to the desired
angle, insert the bolts, and tighten nuts. Attach Rear Legs
to Support Strut, lower collector, and insert Rear Legs into
Rear Feet. Insert bolt and tighten.
Step 4
Step 5
Position collector face up on the Support Strut, insert clips
into Support Strut, and secure collector to Support Strut
with clips. SunEarth recommends placing the Support Strut
approximately 10 ~ 20% in from each end of the collector for
maximum strength.
Assemble Rear Legs[ , and ] and position the legs to the
desired angle using the pre-drilled holes (See Angle and Spacing
Table below). Mark the position of Rear Feet and securely fasten
to mounting surface. Detach the Rear Leg from the Support
Strut and Rear Feet. Lower the Support Strut to the mounting
surface.
www.sunearthinc.com
2 4 6
Step 3
20°26°29°38°40°45°50°55°60°
MTG-LSR-52-19 51.75"--------
MTG-LSR-52-25.5 - 54.5" 42.5"------
MTG-LSR-52-40 - - - 62.25"59.25"51"39.25" - -
24°26°31°38°40°45°50°55°60°
MTG-LSR-42-19 42.5" 34.75"-------
MTG-LSR-42-25.5 - - 45.5" 30.5" - - - - -
MTG-LSR-42-40 - - - - - 54.75"49"43.5" 37.75"
22°25°29°34°42°45°50°55°60°
MTG-LSR-52-19 46.25"39.25"-------
MTG-LSR-52-25.5 - - 49"35.5" - - - - -
MTG-LSR-52-40 - - - - 57.5" 54.5" 48"41"32.5"
27°32°36°40°45°49°50°55°60°
MTG-LSR-42-19 37.25"27.75"------ -
MTG-LSR-42-25.5 - - 40.75"36"28"----
MTG-LSR-42-40 - - - - - 50.75"50"46.25"42.25"
1st Hole
2nd Hole
Angle and Foot Spacing Table
Models may include more than two rear leg
positioning holes. Utilization of holes other than
the two outer most holes is PROHIBITED, since
doing so may impact the structural capacity of
the rack.