Vivo STAND-V032 User manual

Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v032
SKU: STAND-V032
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1)
Pole
B(x1)
Clamp
C(x1)
Swivel Arm
D (x2)
VESA Plate
S-A (x3)
M6x16mm Screw
S-B (x2)
M6 Security
Nut
M-A (x8)
M4x12mm
Thumbscrew
E (x1)
Grommet
Base Plate
F (x1)
So Pad
G(x1)
Support
Plate
H (x1)
Pole Cap
I (x1)
Pole Cable
Clip
J(x4)
Arm Cable
Clip
M-B (x8)
M4x30mm Screw
M-C (x8)
M6 Spacer
T-A (x1)
3mm Allen
Wrench
T-B (x1)
5mm Allen
Wrench
T-C (x1)
6mm Allen
Wrench

3
ASSEMBLY STEPS
TOOLS NEEDED
22 lbs
Per Arm
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 1
STEP 2A: DESK CLAMP
Loosen knob on Clamp (B).
B
Mount Clamp (B) to Pole (A) using M6x16mm Screws (S-A) 3mm Allen Wrench (T-A).
Secure assembly to desktop by tightening knob on Clamp (B).
B
A
S-A
T-A

4
STEP 2B: GROMMET MOUNT
Grommet Installation
Using a phillips screwdriver, remove the screw from Clamp (B) and disassemble. Set Knob
(B2) aside. Mount Grommet Plate (E) to Pole (A) using M6x16mm Screws (S-A) and 3mm
Allen Wrench (T-A). Remove adhesive backing from So Pad (F) and adhere to Grommet
Plate (E). Using a 3/8” (10mm) drill bit, drill through desktop surface and secure assembly
using Knob (B2) and Support Plate (G).
B
B2
E
S-A
T-A
A
F
B2
G

5
STEP 3
STEP 4
Slide Pole Cable Clip (I) and Swivel Arm (C) onto Pole (A). Secure Swivel Arm (C) in place
using 6mm Allen Wrench (T-C). Attach Pole Cap (H) to Pole (A). Attach Arm Cable Clips (J)
to Swivel Arm (C).
H
C
I
AT-C
J
Secure VESA Plates (D) to monitors using M4x12mm Thumbscrews (M-A) or M4x30mm
Screws (M-B). M6 Spacers (M-C) may be required.
D
M-A
D
M-B
M-C

6
STEP 5
STEP 6
Slide monitors with VESA Plates (D) onto Swivel Arm (C). Secure VESA Plates (D) in place
using M6 Security Nuts (S-B).
S-B
DC
Manage cables using Arm Cable Clips (J) and Pole Cable Clip (I).
JI

7
STEP 6
Adjust the monitor tilt using 5mm Allen Wrench (T-B). To level monitors, remove M6
Security Nuts (S-B) and tighten or loosen adjustment screws using 3mm Allen Wrench
(T-A). Once level, fasten M6 Security Nuts (S-B) back into place.
T-B
S-B
T-A

LAST UPDATED: 08/19/2022
REV1
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303