Suntex Cl1045n User manual

TFT LCD COLOR MONITOR

CL1045N/CL1045NT

DEAR CUSTOMERS

Thank you for purchasing the liquid crystal display monitor. This product employs

new integrate circuits and high quality TFT LCD modules. It is putting out with its

low power consumption, emits no radiation, and other advantage characteristics. This

product is shaped with modern style and is easy to be carried with. The color

TFTLCD is the most suitable display for VGA,VCD, DVD and GPS system for

motorcars and ships .It also can be used in the office ,in flat ,at home also in other

suitable position. You will certainly benefit from this monitor in lots of ways, to name

some of them: convenience, safety, space-saving.

We hope that you will have the enjoyment of your new mini color TFT LCD.

To ensure the best use of the unit, please read this handbook carefully beforehand.

CAUTION

1. Please use the adapter attached in the accessory.

2. Do not expose this product to direct sunlight, heat or humid conditions.

3. Keep away from strong light while using this product so as to obtain the

clearest and the most colorful picture.

4. Please avoid heavy impact or drop onto the ground.

5. Do not use chemical solutions to clean this unit. Please simply wipe with a

clean soft cloth to keep the brightness of the surface.

6. If the product does not operate normally when the instructions are followed.

Adjust only those controls that are covered by the instructions. Improper

adjustment of other controls may result in damage and will often require

extensive work of a qualified technician.

CONTENTS

1. PRODUCT DESCRIPTION --------------------

2. REMOTE CONTROLLER ---------------------

3. MENU OPERATION ----------------------------

IN AV MODE--------------------------------------

IN PC MODE--------------------------------------

IN DVI&HDMI&YPBPR MODE--------------

4. MATCHED CABLES-------------------------

5. ACCESSORIES ------------------------------------

6. PARAMETER --------------------------------------

7. TROUBLESHOOTING ---------------------------

8. REMARK----------------------------------------

1. PRODUCT DESCRIPTION

Picture

1 2 3 4 5 6 7 8

18 17 16 15 14 13 12 11 10 9

1. - : Volume down or to adjust the value of setting function

2. +: Volume up or to adjust the value of setting function

3. <: Selection key, to select item on the OSD or push the key in PC mode

directly to adjust phase automatically

4. >: To select function on OSD or to adjust the brightness directly. There

are six levels of brightness, push this button directly to change among

them.

5. MENU: To activate OSD menu

6. PC/AV: PC, AV switch

7. POWER: Power on/off

8. Infrared receiving Window

9. DC 12V

10. S-video input

11. DVI input

12. HDMI input

13. Ypbpr input

14. VGA input

15. Video 1/2 input

16. Audio L/R input

17. Audio L/R output

18. USB input(Touch connector)

2. REMOTE CONTROLLER

Picture 2

: POWER ON/OFF

: MUTE

: Display inputted mode

: To activate OSD menu

: Volume down or to adjust the value of setting function

: Volume up or to adjust the value of setting function

: To select function on OSD

: AV1, AV2, PC switch

~: Number key, no use

: Unit, double-digit, three-Picture, no use.

: NO USE

3. MENU OPERATION

After connecting power, the unit will be in standby state. Press ”POWER” on the unit

or on the remote controller, the buttons of the unit will light, the POWER is red ,the

others are blue, at that time the unit begins to work. Press the same button again the

unit will return to its standby state (Note the blue button will black out in 5 or 6

seconds soon after you turn off unit.). When it is working push “PC/AV” on the unit

or on the remote controller to switch between AV and PC.

IN AV MODE & S-video

You can press “</>”on the unit to select the item demanded among , , ,

,,, , , , , (in line: brightness ,contrast ,

saturation, tint , sharpness, language , reset , OSD H- position, OSD

V-position ,OSD duration, exit OSD )and the selected items background will be

yellow and the explanation of the item will display in the window which on the right

side of the OSD menu . For touch screen function please download the driver for

touch screen from our website 。Then press “</>”on the unit or “ /” on the

remote controller to select other item to adjust or to select to exit the OSD.

Other ways you can push “>” on the unit to switch the level of brightness directly,

there is 6 levels of brightness approved.

BRIGHTNESS: Press “</>”on the unit or “ /” on the remote controller to

select ,and then press +/ - of the unit or /to adjust the luminance of

BRIGHTNESS as your desire.

CONTRAST: Press “</>”on the unit or “ /” on the remote controller to

select , then you can press +/ - of the unit or /to adjust the level of

contrast as your desire.

SATURATION: Press “</>”on the unit or “ /” on the remote controller to

select , then push +/ - of the unit or /on the remote controller to

adjust the level of saturation as your desire.

TINT: Press “</>”on the unit or “ /” on the remote controller to select ,

then push +/ - of the unit or /on the remote controller to adjust the hue

of image as your desire.

SHARPNESS: Press “</>”on the unit or “ /” on the remote controller to

select , then push +/ - of the unit or /on the remote controller to adjust

the level of sharpness as your desire.

LANGUAGE: There is 2 language approved of the menu, namely English and

Chinese. You can press “</>”on the unit or “ /” on the remote controller

to select , Then push +/ - of the unit or /on the remote controller

to select the langue that you need.

RESET: You can press “</>”on the unit or “ /” on the remote controller to

select , Then push +/ - of the unit or /on the remote controller to

choose “YES “ and it will reset to original mode , after that you can reset

adjustment of the unit as your desire once more OSD COLOR

TEMPERATURE RESET

OSD POSITION ADJUSTMENT: Press “</>”on the unit or “ /” on the

remote controller to select , then push +/ - of the unit or /on the

remote controller and the OSD will move in horizontal direction. Press +/ is

to make the OSD move to right, -/ is to make the OSD move to left.

OSD V-PODITION: Press “</>”on the unit or “ /” on the remote

controller to select , then push +/ - of the unit or /on the remote

controller and the OSD will move in vertical direction as your operation. Press

+/ is to make the OSD move to up, -/ is to make the OSD move to down.

OSD DURATION: Press “</>”on the unit or “ /” on the remote controller

to select , then you can adjust the duration of OSD by pressing +/ - of the

unit or /on the remote controller. Push +/ to extend the period of

duration, push -/ to shorten the period of duration .The duration of OSD is

up to 100 seconds. （switch-on long term, and recovering when switch-off）

EXIT OSD: You can press “</>”on the unit or “ /” on the remote

controller to select , and then press “+/-”of the unit to select “YES” and it

will exit the OSD.

IN PC MODE:

You can press “</>”on the unit to select the item demanded among , ,

, , ，, ，, , , (in line:

brightness ,contrast , saturation, tint , sharpness, language , reset , OSD H-

position, OSD V-position ,OSD duration, exit OSD )and the selected items

background will be yellow and the explanation of the item will display in the window

which on the right side of the OSD menu . For touch screen function please download

the driver for touch screen from our website 。Then press “</>”on the unit or

“/” on the remote controller to select other item to adjust or to select to

exit the OSD. Other ways you can push “>” on the unit to switch the level of

brightness directly, there is 6 levels of brightness approved.

BRIGHTNESS: Press “</>”on the unit or “ /” on the remote controller to

select ,and then press +/ - of the unit or /to adjust the luminance of

BRIGHTNESS as your desire.

CONTRAST: Press “</>”on the unit or “ /” on the remote controller to

select , then you can press +/ - of the unit or /to adjust the level of

contrast as your desire.

PHASE: You can press “</>”on the unit or “ /” on the remote controller to

select . Then push +/ - of the unit or /on the remote controller to

adjust the beginning point and terminal point of image station as your desire.

CLOCK: You can press “</>”on the unit or “ /” on the remote controller

to select . Then push +/ - of the unit or /on the remote controller to

adjust the range of image as your desire.

OSD H-POSITION: You can press “</>”on the unit or “ /” on the remote

controller to select , Then push +/ - of the unit or /on the remote

controller to adjust the OSD position in horizontal direction as your desire.

V-POSITION: You can press “</>”on the unit or “ /” on the remote

controller to select , Then push +/ - of the unit or /on the remote

controller to adjust the OSD position in vertical direction as your desire.

RESET: You can press “</>”on the unit or “ /” on the remote controller to

select ,Then push +/ - of the unit or /on the remote controller to

choose “YES “ and it will reset to original mode , after that you can reset

adjustment of the unit as your desire once more OSD COLOR

TEMPERATURE RESET

COLOR TEMPERATURE: You can press “</>”on the unit or “ /” on the

remote controller to select , you can choose to set color temperature at first

such as: 6500 Ks, 7500 Ks or 9300 Ks. You can also adjust a color temperature

that wants the options “USER" then can adjust RED, GREEN and

BLUE at will. With attain which want of the color value.

LANGUAGE: There is 2 language approved of the menu, namely English and

Chinese. You can press “</>”on the unit or “ /” on the remote controller

to select ,Then push +/ - of the unit or /on the remote controller

to select the langue that you need.

MISCELLANEOUS: You can press “</>”on the unit or “ / ” on the remote

controller to select to subdirectories,

As follows:

OSD MISCELLANEOUS

You can press “</>”on the unit to select the item demanded among , ,

, , , (in line: exit OSD, OSD H- position, OSD V-position , OSD

DURATION , OSD AUTO COLOR )and the selected items background will be

yellow and the explanation of the item will display in the window which on the right

side of the OSD menu . For touch screen function please download the driver for

touch screen from our website 。Then press “</>”on the unit or “ /” on the

remote controller to select other item to adjust or to select to exit the OSD. The

idiographic function of the menu is the same with above