Sunx FX-502 Series User manual
INSTRUCTION MANUAL
Photoelectric Sensor 'LJLWDO)LEHU6HQVRU$PSOL¿HU
);Ƒ
ME-FX502 No.0012-66V
Thank you very much for purchasing SUNX products. Please read this In-
struction Manual carefully and thoroughly for the correct and optimum use
of this product.
Kindly keep this manual in a convenient place for quick reference.
WARNING
Never use this product as a sensing device for personnel protection.
In case of using devices for personnel protection, use products which
meet laws and standards, such as OSHA, ANSI or IEC etc., for person-
nel protection applicable in each region or country.
Ɣ
Ɣ
1PART DESCRIPTION
<Description of the operation part>
UP key SET key DOWN key MODE key
Select setting items
•
&RQ¿UPWKHVHWWLQJ
contents
•
Select setting items
•
Select a mode
Cancel during setting
Select sensing output
1/2 by long pressing
•
•
•
2MOUNTING
How to connect
1. Fit the rear part of the mounting section of the
DPSOL¿HURQDPPZLGWK',1UDLO
2.
Press down the rear part of the mounting section
RIWKHXQLWRQWKHPPZLGWK',1UDLODQG¿WWKH
front part of the mounting section to the DIN rail.
How to remove
1. Push the controller forward.
2.
/LIWXSWKHIURQWSDUWRIWKHDPSOL¿HUWRUHPRYHLW
Note:7DNHFDUHWKDWLIWKHIURQWSDUWLVOLIWHGZLWKRXWSXVKLQJWKHDPSOL¿HUIRUZDUGWKHKRRN
on the rear portion of the mounting section is likely to break.
+RZWRFRQQHFWWKH¿EHUFDEOH
%HVXUHWR¿WWKHDWWDFKPHQWWRWKH¿EHUV¿UVWEHIRUHLQVHUWLQJWKH¿EHUVWRWKH
DPSOL¿HU)RUGHWDLOVUHIHUWRWKH,QVWUXFWLRQ0DQXDOHQFORVHGZLWKWKH¿EHUV
6QDSWKH¿EHUORFNOHYHUGRZQWLOOLWVWRSVFRP-
pletely.
,QVHUWWKH¿EHUFDEOHVVORZO\LQWRWKHLQOHWVXQWLO
they stops. (Note 1)
5HWXUQ WKH¿EHUORFN OHYHUWRWKH RULJLQDOSRVL-
tion till it stops.
1RWHV ,QFDVHWKH¿EHUFDEOHVDUHQRWLQVHUWHGWRDSRVLWLRQZKHUHWKH\VKRXOGVWRSWKH
VHQVLQJUDQJHLVUHGXFHG6LQFHDÀH[LEOH¿EHULVHDVLO\EHQWWDNHFDUHZKHQLQ-
VHUWLQJ¿EHU
:LWKWKHFRD[LDOUHÀHFWLYHW\SH¿EHUVXFKDVFD-G4 or FD-FM2, insert the single
FRUH¿EHUFDEOHLQWRWKHEHDPHPLWWLQJLQOHW³3´DQGWKH0XOWLFRUH¿EHUFDEOHLQWR
the beam-receiving inlet.
If they are inserted in reverse, the sensing performance will deteriorate.
3WIRING
Make sure to connect or disconnect the quick-connection cable (optional)
in the power supply OFF condition.
How to connect
1. Hold the connector of the quick-connection
cable, and align its release lever with the
groove at the top portion of the controller
connector.
2. Insert the connector till a click is felt.
MODE key
Sensing output 1
selection indicator
(Yellow)
DOWN key
Sensing output 2
selection indicator
(Yellow)
'LJLWDOGLVSOD\*UHHQ5HG
UP key
SET key
Sensing output 1
operation indicator
(Orange)
Sensing output 2
operation indicator
(Orange)
MODE indicator: CUST (Yellow)
02'(LQGLFDWRU352<HOORZ
MODE indicator: L / D (Yellow)
Fiber lock
lever
Fiber
21
PPZLGWK',1UDLO
2
1
Quick-connection
cable (Optional)
Groove
5HOHDVHOHYHU
How to remove
1. Press the release lever at the top of the
quick-connection cable connector, and pull
out the connector.
Note:
Take care that if the connector is pulled out without pressing the release lever, the re-
lease lever may break. Do not use a quick-connection cable whose release lever has
broken. Furthermore, do not pull by holding the cable, as this can cause a cable-break.
7HUPLQDODUUDQJHPHQW!
Terminal
No. Terminal name
1+V
2 Sensing output 1
0V
46HQVLQJRXWSXW([WHUQDORXWSXW
4INSTALL MORE AMPLIFIER OF SERIES CON-
NECTION TYPE
Make sure that the power supply is OFF while adding or removing the
series connection type.
Make sure to check the allowable ambient temperature since it depends
on the number of the series connection types connected in cascade.
In case 2 or more the series connection types are connected in cas-
cade, make sure to mount them on a DIN rail.
:KHQWKHDPSOL¿HUVPRYHRQWKH',1UDLOGHSHQGLQJRQWKHDWWDFKLQJFRQ-
GLWLRQRUWKHDPSOL¿HUVDUHPRXQWHGFORVHWRHDFKRWKHULQFDVFDGH¿WWKHP
between the end plates MS-DIN-E (optional) mounted at the two ends.
,QFDVHLQVWDOOLQJDGGLWLRQDODPSOL¿HURIVHULHVFRQQHFWLRQW\SHWKHPD[-
imum 11 the series connection types using sub cables can be added to
DQDPSOL¿HUXVLQJDPDLQFRQQHFWLRQFDEOH
When connecting 2 or more the series connection types in cascade, use
the sub cable (optional) for the second series connection type onwards.
When connecting the series connection type are not close to each other in parallel,
be sure to mount the end plate MS-DIN-ERSWLRQDODWERWKVLGHVRIHDFKDPSOL¿HU
)RURSWLFDOFRPPXQLFDWLRQUHIHUWR³ OPTICAL COMMUNICATION´
)RULQWHUIHUHQFHSUHYHQWLRQ IXQFWLRQUHIHUWR ³ INTERFERENCE
PREVENTION FUNCTION´
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
)RUPRXQWLQJDQGUHPRYLQJWKHDPSOL¿HUUHIHUWR³ MOUNTING´
How to cascade
0RXQWWKHDPSOL¿HUVRQHE\RQHRQ
WKHPPZLGWK',1UDLO
6OLGHWKHDPSOL¿HUVQH[WWRHDFKRWK-
er, and connect the quick-connection
cables.
0RXQWWKHHQGSODWHVMS-DIN-E (op-
tional) at both the ends to hold the
DPSOL¿HUVEHWZHHQWKHLUÀDWVLGHV
4.
7LJKWHQ WKHVFUHZVWR IL[WKHHQG
plates.
How to remove
1. Loosen the screws of the end plates.
5HPRYHWKHHQGSODWHV
6OLGHWKHDPSOL¿HUVDQGUHPRYHWKHP
one by one.
5I/O CIRCUIT DIAGRAM
<FX-502>
<FX-502P>
Notes: 1) The quick-connection sub cable does not incorporate +V (brown) and 0V (blue).
The power is supplied from the connector of the main cable.
P$PD[LIRUPRUHVHULHVFRQQHFWLRQW\SHDUHFRQQHFWHGWRJHWKHU
'RQRWXVHWKHFRQWUROOHUVLQDVHULHV$1'FRQQHFWLRQ
5HOHDVH
lever
2
1
4
Slide
Sub cable
(Optional)
Main cable
(Optional)
End plate MS-DIN-E
(Optional)
End plate
MS-DIN-E
(Optional)
Communication
window
Slide
Terminal No. Color code of quick-connection cable
(Brown) +V (Note 1)
Load
(Black) Sensing output 1
:KLWH6HQVLQJRXWSXW([WHUQDOLQSXW
Internal circuit Users’ circuit
(Blue) 0V (Note 1)
12 to 24V DC
±10%
+
-
Main circuit
P$PD[1RWH
Terminal No. Color code of quick-connection cable
(Brown) +V (Note 1)
P$PD[1RWH
Load
:KLWH6HQVLQJRXWSXW([WHUQDOLQSXW
Internal circuit Users’ circuit
(Blue) 0V (Note 1)
12 to 24V DC
±10%
+
-
Main circuit
(Black) Sensing output 1
6OPERATION PROCEDURE
The changed contents are not stored if turning the power OFF while set-
WLQJ7KHUHIRUHPDNHVXUHWRFRQ¿UPWKHVHWWLQJVE\SUHVVLQJWKH6(7NH\
before turning the power OFF.
When turning ON the power, normal condition is displayed and the digital
display shows the threshold value (green) and the incident light intensity
(red).
When pressing MODE key, the mode changes as per the diagram below.
7TEACHING MODE
Make sure that detection may become unstable if less margin is applied
in the use environment when teaching.
When teaching in Window comparator mode or Hysteresis mode, a set-
WLQJKDVWREHPDGHLQ352PRGHEHIRUHKDQG
In case one point teaching, make sure to set the shift amount. (initial
value is 10% or 100)
For setting, refer to <PRO 6>LQ³ PRO MODE´
1RUPDOO\³ ´or ³ ´EOLQNVDVDUHVXOWRIVWDELOLW\GHWHFWLRQ
Ɣ
Ɣ
Ɣ
7HDFKLQJFDQEHVHWLQ581PRGH
SRLQWWHDFKLQJ
/LPLWWHDFKLQJ
Note:
7KHVKLIWYDOXHRIDSSR[LVDQLQLWLDOYDOXH7KHVKLIWYDOXHFDQEHFKDQJHWRGLV-
SOD\LQSHUFHQW>$SSUR[WRXQLW@RULQFLGHQWOLJKWLQWHQVLW\>WR8QLW@
For setting the shift amount, refer to 3526KLIWDPRXQW VHWWLQJ!LQ³ PRO
MODE´
)XOODXWRWHDFKLQJ
Ɣ
Ɣ
Ɣ
Displays threshold value (green) and incident light intensity (red).
7HDFKLQJDQGWKUHVKROGYDOXH¿QH DGMXVWPHQWDQGNH\ORFNIXQF-
tion can be set.
)RUVHWWLQJ PHWKRG RIHDFKIXQFWLRQ UHIHU WR³ TEACHING
MODE´³ THRESHOLD VALUE FINE ADJUSTMENT FUNC-
TION´RU³ KEY LOCK FUNCTION´
•
•
•
Select either Light-ON or Dark-ON
)RUWKH VHQVLQJ RXWSXWRSHUDWLRQPRGHUHIHU WR ³ SENSING
OUTPUT OPERATION MODE´
7KHGHIDXOWVHWWLQJLV³ ´/LJKW21
•
•
•
$QLWHPVHWLQ&86720PRGH5HVSRQVHWLPHVHWWLQJ(PLVVLRQ
power setting and Hysteresis setting) is displayed.
)RUGHWDLOVUHIHUWR³ CUSTOM MODE´
7KHGHIDXOWVHWWLQJLV³ ´UHVSRQVHWLPHVHWWLQJ
•
•
•
Advanced setting can be done.
)RUWKHVHWWLQJUHIHUWR³ PRO MODE´
•
•
581PRGH!
6HQVLQJRXWSXWRSHUDWLRQPRGH!
&86720PRGH!
352PRGH!
3UHVVWKH6(7NH\LQWKHVHQVLQJREMHFWSUHVHQWFRQGLWLRQ
³ ´LVGLVSOD\HGLQWKHGLJLWDOGLVSOD\JUHHQDQGWKHDOO02'(LQGLFDWRUV
(yellow) brink.
3UHVVWKH6(7NH\LQWKHVHQVLQJREMHFWDEVHQWFRQGLWLRQ
$WKUHVKROGYDOXHLVVHWEHWZHHQWKHVWHSDQG
,QFDVHVWDEOHVHQVLQJLVSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
,QFDVHVWDEOHVHQVLQJLVQRWSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
or
³
´
is displayed by pressing down UP key in the digital green display in
VWHSDQG³
´
is displayed by pressing down DOWN key in the digital
yellow display in step 2.
,QFDVHVWDEOHVHQVLQJLVSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
,QFDVHVWDEOHVHQVLQJLVQRWSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
2. Press down UP key or DOWN key
3UHVVGRZQ83NH\7KHWKUHVKROGOHYHOLV VKLIWHG WRDYDOXHDSSUR[
higher (low sensitivity) than that set at step 1. (Note 1)
3UHVVGRZQ'2:1NH\7KHWKUHVKROGOHYHOLVVKLIWHGWRDYDOXHDSSUR[
lower (high sensitivity) than that set at step 1. (Note 1)
3UHVVWKH6(7.H\LQWKHVHQVLQJREMHFWSUHVHQWFRQGLWLRQ
³ ´LVGLVSOD\HGLQWKH'LJLWDOJUHHQGLVSOD\DQGWKHDOO02'(LQGLFDWRUV
(yellow) brinks.
or
or
³ ´LVGLVSOD\HGRQWKHGLJLWDOGLVSOD\JUHHQDQGZKHQWKHVHQVLQJRE-
MHFWSDVVHGWKURXJKUHOHDVHWKH6(7NH\
,QFDVHVWDEOHVHQVLQJLVSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
,QFDVHVWDEOHVHQVLQJLVQRWSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
5XQWKHVHQVLQJREMHFWRQWKHOLQHDQGKROGGRZQWKH6(7NH\
or
1.
%\SUHVVLQJGRZQ6(7NH\³
´LVGLVSOH\HGRQWKHGVLWDOGLVSOD\JUHHQ
and, all MODE indicators (yellow) brink.
Automatic
SRLQWWHDFKLQJLQ:LQGRZFRPSDUDWRUPRGHH[FHSWVHQVLQJRXWSXW
or Hysteresis mode
This is the method to set the shift amount to the desired value and to set
the threshold range by using the 1-point teaching.
SRLQWWHDFKLQJLQ:LQGRZFRPSDUDWRUPRGHH[FHSWVHQVLQJRXWSXW
or Hysteresis mode
This method is to set the threshold range by using the 2-point teaching (P-1, P-2.)
:KHQFRQGXFWLQJWHDFKLQJ XVHVHQVLQJREMHFWV3DQG3ZKRVH
incident light intensity is different from each other.
SRLQWWHDFKLQJLQ:LQGRZFRPSDUDWRUPRGHH[FHSWVHQVLQJRXWSXW
or Hysteresis mode
7KLVLVWKHPHWKRGWRFRQGXFWWKHSRLQWWHDFKLQJ333DQGWRVHW
the threshold range by setting the threshold (1_SL) of the mid-point between
³$´DQG³%´DQGWKHWKUHVKROGB6/RIWKHPLGSRLQWEHWZHHQ³%´DQG³&´
:KHQFRQGXFWLQJWHDFKLQJXVHVHQVLQJREMHFWV$%DQG&ZKRVHLQFL-
dent light intensities are different.
$IWHUWHDFKLQJ33DQG3ZLOOEHDXWRPDWLFDOO\UHORFDWHGLQDVFHQGLQJRUGHU
LHWKHORZHVWYDOXHLVSODFHGLQ³$´WKHVHFRQGORZHVWLQ³%´DQGWKHKLJKHVWLQ³&´
6SDQDGMXVWPHQWLQ5LVLQJGLIIHUHQWLDOPRGHRU7UDLOLQJGLIIHUHQWLDOPRGH
7KHVSDQDGMXVWPHQW LQULVLQJGLIIHUHQWLDOPRGHRUWUDLOLQJGLIIHUHQWLDO
mode can be set by pressing down the UP key or DOWN key after
pressing down SET key. At this time, all Mode indicators blinks.
3UHVV6(7NH\WRFRQ¿UPWKHVHWWLQJ
7KHWKUHVKROGFDQ EHVHWE\ XVLQJWKHWKUHVKROG YDOXH¿QHDGMXVWPHQW
IXQFWLRQ)RUWKH WKUHVKROGYDOXHILQHDGMXVWPHQWIXQFWLRQUHIHUWR
³THRESHOLD VALUE FINE ADJUSTMENT FUNCTION´
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
<Window comparator mode>
Set to de-
sired value
Set to de-
sired value
1_SL P-1 2_SL
<Hysteresis mode>
Set to de-
sired value
Set to de-
sired value
1_SL P-1 2_SL
7KHWKUHVKROGYDOXHB6/WKDWLVORZHUIURPWKHLQFLGHQWOLJKWLQWHQVLW\
and the threshold value (2_SL) that is 10% higher from the incident light in-
tensity are set. (Note 1, 2)
,QFDVHVWDEOHVHQVLQJLVSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
,QFDVHVWDEOHVHQVLQJLVQRWSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
Notes: 1)
The shift amount of 10% is an initial value. The shift amount can
EHVHWLQ352PRGH)XUWKHUPRUH
the shift value can be set in
incident light amount.
For setting method, refer to <PRO 6>LQ³
PRO MODE´
,IWKH YDOXHDIWHU VHWWLQJH[FHHGVWKHPD[LPXPPLQLPXP WKH
PD[LPXPPLQLPXPVHQVLWLYLW\ZLOOEHVHW
or
3UHVVGRZQWKH6(7NH\LQWKHVHQVLQJREMHFWSUHVHQWFRQGLWLRQ
1.
%\SUHVVLQJGRZQ6(7NH\³
´LVGLVSOH\HGRQWKHGVLWDOGLVSOD\JUHHQ
and, all MODE indicators (yellow) brink.
<Hysteresis mode>
1_SL (P-1) 2_SL (P-2)
<Window comparator mode>
1_SL (P-1) 2_SL (P-2)
7KHYDOXHRIWKH¿UVWSRLQWB6/DQGWKHVHFRQGSRLQWB6/DUHVHWJUHHQ
(Note)
,QFDVHVWDEOHVHQVLQJLVSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
,QFDVHVWDEOHVHQVLQJLVQRWSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
Note,IWKHYDOXH DIWHU VHWWLQJ H[FHHGV WKH PD[LPXPPLQLPXPWKH
PD[LPXPPLQLPXPVHQVLWLYLW\ZLOOEHVHW
2
³ ´LVGLVSOD\HGLQWKHGLJLWDOGLVSOD\JUHHQDQGWKHDOO02'(LQGLFDWRUV\HOORZEULQN
3UHVVGRZQWKH6(7NH\LQWKHREMHFWSUHVHQWFRQGLWLRQIRUWKHVHFRQGSRLQW
3UHVVGRZQWKH6(7NH\LQWKHVHQVLQJREMHFWSUHVHQWFRQGLWLRQ
or
<Hysteresis mode>
A 2_SL1_SL B C
<Window comparator mode>
A 2_SL1_SL B C
7KHWKUHVKROGB6/RIWKHPLGSRLQWEHWZHHQ³$´DQG³%´DQGWKHWKUHVKROG
B6/RIWKHPLGSRLQWEHWZHHQ³%´DQG³&´DUHVHW1RWH
,QFDVHVWDEOHVHQVLQJLVSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
,QFDVHVWDEOHVHQVLQJLVQRWSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
Note,IWKHYDOXH DIWHU VHWWLQJ H[FHHGV WKH PD[LPXPPLQLPXPWKH
PD[LPXPPLQLPXPVHQVLWLYLW\ZLOOEHVHW
³ ´LVGLVSOD\HGLQWKHJUHHQGLJLWDOGLVSOD\
3UHVVGRZQ WKH 6(7NH\ LQWKHVHQVLQJREMHFW SUHVHQW FRQGLWLRQIRUWKH
second point
³ ´EOLQNVLQWKHJUHHQGLJLWDOGLVSOD\
3UHVVGRZQWKH6(7NH\LQWKHVHQVLQJREMHFWSUHVHQWFRQGLWLRQIRUWKHWKLUGSRLQW
or
3UHVVGRZQWKH6(7NH\LQWKHVHQVLQJREMHFWSUHVHQWFRQGLWLRQ
Short span
(Changed intensity)
Press Long span
(Changed intensity)
8
THRESHOLD VALUE FINE ADJUSTMENT FUNCTION
6HWWKH¿QHDGMXVWPHQWRIWKUHVKROGYDOXHLQ581PRGH
Pressing down the UP key increases the threshold value, and Pressing
down the DOWN key decreases the threshold value.
:KHQVHWWLQJVHQVLQJRXWSXWWRWKHZLQGRZFRPSDUDWRUPRGHRUK\VWHUHVLVPRGH³
´DQGRU ³ ´FDQEHFKDQJHGWRDQRWKHUE\SUHVVLQJGRZQ WKH83NH\IRUVHF
,QFDVHFRQGXFWLQJ WKUHVKROGYDOXHILQH DGMXVWPHQWRI³ ´ RU³ ´
SUHVVGRZQ83NH\RU'RZQNH\DQG³ ´RU³ ´DUHGLVSOD\HG7KHQ
WKHWKUHVKROGYDOXH¿QHDGMXVWPHQWFDQEHFRQGXFWHG
Set by pressing down the SET key or the value is automatically memorized
unless any key operation is carried out within a certain period of time.
For setting of the sensing output, refer to <PRO 6>LQ³ PRO MODE´
1RUPDOPRGH5LVLQJGLIIHUHQWLDOPRGHRU7UDLOLQJGLIIHUHQWLDOPRGH!
<Window comparator mode or Hysteresis mode>
Note: It may not respond when values of ³ ´DQG³ ´DUHFORVHEHFDXVHRIUHOD-
WLRQRIK\VWHUHVLV%HVXUHWRFRQ¿UPZLWKWKLVGHYLFH
<Forced ON output mode or Forced OFF output mode>
9KEY LOCK FUNCTION
The key lock function prevents key operations so that the conditions set
in each setting mode are not inadvertently changed.
%\NHHSLQJWRSUHVVGRZQWKH6(7NH\DQGWKH02'(NH\IRUVHFRU
more, setting and releasing of key lock can be done.
,IRSHUDWLQJNH\VZLWFKDIWHUNH\ORFNLVVHW³ ´LVLQGLFDWHGRQ
the digital display.
6HWNH\ORFN!
5HOHDVHNH\ORFN!
10
SENSING OUTPUT OPERATION MODE
When MODE indicator: L / D (yellow) lights up, sensing output operation can be set.
By pressing UP key or DOWN key, sensing output operation will be changed.
3UHVV6(7NH\WRFRQ¿UPWKHVHWWLQJ
11
CUSTOM MODE
:KHQ02'(LQGLFDWRU&867\HOORZOLJKWVXS5HVSRQVHWLPHVHWWLQJ
Emission power setting or Hysteresis setting can be displayed.
Setting contents of the displayed item can be changed.
For the setting procedure, refer to 352&86720VHWWLQJ!LQ³ PRO MODE´
By pressing UP key or DOWN key, the setting in each item will be changed.
3UHVV6(7NH\WRFRQ¿UPWKHVHWWLQJ
For setting of each item, refer to the following table.
Item Digital display 5HIHUHQFHLWHP
5HVSRQVH
time setting
3525HVSRQVHWLPHVHWWLQJ! in
³PRO MODE´
Emission
power setting
352(PLVVLRQSRZHUVHWWLQJ! in
³PRO MODE´
Hysteresis
setting
352+\VWHUHVLVVHWWLQJ! in
³PRO MODE´
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
581PRGH!
6HWWLQJRINH\ORFN!
Press down for
VHFRUPRUH
Automatic
581PRGH!
5HOHDVHRINH\ORFN!
Automatic
Press down for
VHFRUPRUH
,
are displayed
&RQ¿UPHG
Press
(Light-ON) (Dark-ON)
Press
&RQ¿UPHG
Press
(Threshold value)
Automatic
or
Press
&RQ¿UPHG
(Threshold value)
Press or Press
Automatic
or
Press
or
or
Press Press
(Threshold value)
&RQ¿UPHG
Automatic
Automatic
or
Press
12
PRO MODE
:KHQ02'(LQGLFDWRU352\HOORZOLJKWVXS352PRGHFDQEHVHW
3UHVV6(7NH\WRFRQ¿UPWKHVHWWLQJ
Ɣ
Ɣ
:&RQ¿UPHG :Selected
352PRGH! 352!
ȝVRUOHVV
5HVSRQVHWLPHVHWWLQJ!1RWH
ȝVRUOHVV
24ms or less
2ms or less
ȝVRUOHVV
4ms or less
ȝVRUOHVV
(No timer)
7LPHURSHUDWLRQ!
No timer
OFF-delay timer
When timer is
valid.
ON-delay timer
ON / OFF-delay timer
([FHSWVHQVLQJRXWSXW
One-shot timer
ON-delay / One-shot timer
([FHSWVHQVLQJRXWSXW
5HVSRQVH
time setting
Timer
setting
7LPHUSHULRG!1RWH
Time period depends on timer range.
:KHQXVLQJWKHWLPHUUDQJH³PV´VHWWLQJ
³ ´DSSUR[PV³ ´WR³ ´DSSUR[WRPV
:KHQXVLQJWKHWLPHUUDQJH³VHF´VHWWLQJ
³ ´DSSUR[VHF³ ´WR³ ´DSSUR[WRVHF
:KHQXVLQJWKHWLPHUUDQJH³PV´VHWWLQJ
³ ´DSSUR[PV³ ´WR³ ´DSSUR[
WRPV
(5ms)
OFF-delay
timer
When timer is valid
(Following is for OFF-delay timer selected)
6KLIWDPRXQWVHWWLQJ!
Displayed in percentage
&KDQJHDEOHLQWKHUDQJHRIWR
,QFLGHQWOLJKWLQWHQVLW\1RWH
Shift amount
setting
(15%)
+\VWHUHVLVVHWWLQJ!
Small Large
Standard
(Standard)
Hysteresis
setting
Emission
power setting
(100%)
Middle emis-
sion power
Incident light
intensity
7LPHUUDQJHVHWWLQJ!
ms 1/10ms
sec.
(ms)
Timer range
setting
(SET)
:KHQVHOHFWLQJVDWXUDWLRQFRUUHFWLRQ!
(Correcting)
(*1)
581PRGH!
(*1): In case saturation correction is NG, it is
not displayed.
Saturation
correction
Automatic
Automatic
(PLVVLRQSRZHUVHWWLQJ!1RWH
Saturation correction
High emission power
Changeable in the range of 25 to 100%
Middle emission power
Changeable in the range of 25 to 100%
Low emission power
Changeable in the range of 25 to 100%
7LPHSHULRGKROGVHWWLQJ!1RWH
Hold OFF
Hold ON
(&2VHWWLQJ!
(ECO OFF)
(&2VHWWLQJ!
Eco OFF Full
Eco ON
Time period
hold setting
(Turning OFF)
6HWWLQJRIGLJLWDOGLVSOD\WXUQLQJ!
Turning OFF
Turning ON
352! (Lock OFF)
Teaching
lock setting
7HDFKLQJORFNVHWWLQJ!
Lock OFF
Lock ON
Setting items
in digital
display setting
6HWWLQJLWHPVLQGLJLWDOGLVSOD\VHWWLQJ!
Incident light intensity
Displayed in percentage
Peak / bottom value
Incident light
intensity
Setting of
digital display
turning
(Hold OFF)
352!
352!
6HQVLQJRXWSXWVHWWLQJ!1RWH
Normal mode
Window comparator mode
([FHSWVHQVLQJRXWSXW
5LVLQJGLIIHUHQWLDOPRGH1RWH
7UDLOLQJGLIIHUHQWLDOPRGH1RWH
Hysteresis mode
Self-diagnosis output mode
([FHSWVHQVLQJRXWSXW
Forced ON output mode
Forced OFF output mode
Sensing
output setting
352!
(Default)
Interference
prevention
setting
,QWHUIHUHQFHSUHYHQWLRQ VHWWLQJ!
Default
Different frequency setting
'LIIHUHQWIUHTXHQF\VHWWLQJ!
Emission frequency 1
Emission frequency 2
(PLVVLRQIUHTXHQF\
:KHQVHOHFWLQJGLIIHUHQWIUHTXHQF\VHWWLQJ!
Different fre-
quency setting
Emission
frequency 1
CUSTOM
setting
&86720VHWWLQJ!
5HVSRQVHWLPHVHWWLQJ
Emission power setting
Hysteresis setting
5HVSRQVH
time setting
%OLQNVWLPHV
(Blink)
581PRGH!
5HVHW
setting
Automatic
352!
5HIHUWR³&RGHVHWWLQJWDEOH´
&RQGXFW&RQ¿UPHG
:Select code
Code
setting
(OFF) 'LVSOD\DGMXVWPHQWVHWWLQJ!
OFF
&RQ¿UP
Target setting (Note 6)
'LVSOD\DGMXVW-
ment setting
:KHQVHOHFWLQJWDUJHWVHWWLQJ!
(0)
&RQ¿UPHG
Target
setting
'LVSOD\DGMXVW-
ment setting
Window comparator mode or Hysteresis mode (The following dia-
gram shows in selecting the window comparator mode.)
6KLIWDPRXQWVHWWLQJ!
Shift amount setting
(Displayed in percentage)
352!
/RJLFRSHUDWLRQVHWWLQJ!
Invalid or
and [RU
(Invalid)
(Invalid)
(Invalid)
Logic opera-
tion setting
Between sensing output
1 and sensing output 2
%HWZHHQDGMD-
FHQWDPSOL¿HU
Between
H[WHUQDOLQSXW
Setting of
threshold
value tracking
By pressing down
MODE key long time,
sensing output 1 or
2 can be changed to
another.
352!
,QSXWRXWSXWVHWWLQJ!
Sensing output 2
([WHUQDOLQSXW
Input / output
setting
Back up
ON
%DFNXSVHWWLQJ!
Back up ON
Back up OFF
Back up
setting
6HWWLQJRIGDWDEDQNVDYLQJ!
1 ch 4 ch FK
2 ch 5 ch FK
FK 6 ch
(1 ch)
%OLQNVWLPHV
(good)(YES)
(Blink)
352!
'DWDEDQNORDGLQJ6HWWLQJ!
1 ch 4 ch FK
2 ch 5 ch FK
FK 6 ch
(1 ch)
%OLQNVWLPHV
(good)(YES)
(Blink)
Data bank
loading Setting
Automatic
Automatic
&RS\ORFNVHWWLQJ!
Copy lock OFF
Copy lock ON
Copy lock
setting
352! (YES)
(2 turns)(Blink)
(good)
&RPPXQLFDWLRQSURWRFROVHWWLQJ!
Communication mode
Communication emission
halt
Copy
setting
&RS\DFWLRQVHWWLQJ!
'LVSOD\DGMXVWPHQW
Display copy
'LVSOD\DGMXVWPHQW2))
Automatic
Automatic
Copy action
setting
352!
'LVSOD\DGMXVW-
ment OFF
Communica-
tion protocol
setting
Copy lock
OFF
Communica-
tion mode
([WHUQDOLQSXWVHWWLQJ!
Emission OFF Data bank load
Teaching Data bank save
Limit + 'LVSOD\$GMXVWPHQW
Limit
-
Copy lock (SELF only)
Logic setting (SELF only)
([WHUQDO
input setting
(Only one unit)
(All)
(Emission OFF)
(Emission OFF)
Sensing
output 2
Data bank
loading Setting
Notes: 1) ,Q FDVH UHVSRQVH WLPH VHWWLQJ ³ ´LVVHWWR³ ´³ ´RU³ ´
WKHGLVSOD\IRU LQFLGHQW OLJKW LQWHQVLW\ FDQ VKRZVWKHGLJLWRIPD[,QFDVH
³ ´LVVHOHFWHG,WZLOOGLVSOD\WKHGLJLWRIPD[$QG,QFDVH³ ´RU
³ ´LVVHOHFWHGLWZLOOGLVSOD\WKHGLJLWRIPD[
2) Set timer period after setting timer range since timer period depends on the timer
range.
,QFDVHWKHUHVSRQVHWLPH³ ´LVVHWWR³ ´³ ´RU³ ´WKHPD[L-
PXPOLJKWLQWHQVLW\FDQEHVHWWR$QGWKHUHVSRQVHWLPHLVVHWWR³ ´WKH
PD[LPXPOLJKWLQWHQVLW\FDQEHVHWWR$QGWKHUHVSRQVHWLPHLVVHWWR³
´RU³ ´WKHPD[LPXPOLJKWLQWHQVLW\FDQEHVHWWR
,QFDVHWKHUHVSRQVHWLPHVHWWLQJ³ ´LVVHWWR³ ´ZKHQWKHK\VWHUHVLVVHW-
WLQJ³ ´LV³ ´WKHHPLWWLQJSRZHUEHFRPHVORZVHQVLELOLW\³ ´ZKLFK-
ever selecting
³ ´
³ ´RU³ ´
5) In order to clear the value, set the time period holding function to OFF once. Turn-
ing the power OFF can also clear the value.
6)
,QFDVHWKHUHVSRQVHWLPHVHWWLQJ³ ´LVVHWWR³ ´³ ´RU³ ´WDUJHW
VHWWLQJRIWKHGLVSOD\DGMXVWPHQWVHWWLQJEDQEHVHWIURPWR$QGVHWWLQJWR
³ ´WKHGLVSOD\DGMXVWPHQWVHWWLQJEDQEHVHWIURPWR$QGVHWWLQJWR³
´RU³ ´WKHGLVSOD\DGMXVWPHQWVHWWLQJFDQEHVHWIURPWR
6HW6HQVLQJRXWSXWVHWWLQJDIWHUVHWWLQJ,QSXWRXWSXWVHWWLQJ
,QFDVHXVLQJLQGLIIHUHQWLDOPRGHVHWWKUHVKROGYDOXHRUPRUH
when the hyster-
HVLVVHWWLQJ³ ´LV³ ´DQG
VHWWKUHVKROGYDOXHRUPRUH
when the hyster-
HVLVVHWWLQJ³ ´LV³ ´RU³ ´
.
Item Default
setting Description
5HVSRQVHWLPHVHWWLQJ
Set response time.
Timer setting Set operation and period of the timer.
Hysteresis
setting
Hysteresis can be set when the normal mode or the
window comparator mode is selected.
:KHQVHWWLQJWR³ ´LWEHFRPHVORZVHQVLELOLW\
Shift amount
setting Set shift amount of threshold value in limit teaching.
Emission power
setting
Set emission power.
³ ´ Saturated incident light intensity can be au-
WRPDWLFDOO\DGMXVWHG
³ ´ High emission power (25 to 100%)
³ ´ Middle emission power (25 to 100%)
³ ´ Low emission power (25 to 100%)
Timer range setting
Change unit time of timer.
Teaching lock
setting
Be able to prevent from wrong operation of teaching.
³ ´ Teaching mode is valid
³ ´ Teaching mode is invalid
Digital display
item setting
Incident light intensity can be displayed in percentage or
the peak / bottom value can be displayed on the digital
display (red).
Digital display
turning on setting
Sets the viewing orientation of the digital display.
ECO setting
Power consumption can be lowered.
³ ´(&22))
³ ´,IDQ\NH\RSHUDWLRQLVQRWFDUULHGRXWIRU
VHFLQ581PRGHWKHGLJLWDOGLVSOD\WXUQV
OFF.
³ ´
If key operation is not done in 20 sec. or setting
WKHNH\ORFNIXQFWLRQLQ5XQPRGHDOOLQGLFD-
tors turns OFF.
Period hold
Setting
³ ´3HDN ERWWRP YDOXHLQ WKH GLJLWDOGLVSOD\
refreshing condition can be displayed.
³ ´3HDN ERWWRP YDOXHLQ WKHKROG FRQGLWLRQ
can be displayed.
Data bank loading
/RDGDVHWWLQJIURPVSHFL¿HGGDWDEDQN
Data bank saving
6DYHDVHWWLQJWRVSHFL¿HGGDWDEDQN
Back up
setting
Select to save or not to save the threshold value by
WHDFKLQJLQ((3520
Input / output
setting 6HOHFWHLWKHUVHQVLQJRXWSXWRUH[WHUQDORXWSXW
Copy setting
-
Using optical communications, be able to copy setting
FRQWHQWVLQPDLQDPSOL¿HUWRDOORIWKHVXEDPSOL¿HUV
FRQQHFWHGIURPWKHPDLQDPSOL¿HU
This product cannot send and receive threshold value.
)RUWKHRSWLFDOFRPPXQLFDWLRQVUHIHUWR³ OPTI-
CAL COMMUNICATIONS´
Item Default
setting Description
Copy action
setting
&RS\RILWHPVLQGLVSOD\DGMXVWPHQWVHWWLQJDQG LQFLGHQW OLJKW LQ-
tensity are conducted or canceled by using optical communication.
In case incident light intensity does not have enough
margin, automatically set optimum value.
)RUWKHRSWLFDOFRPPXQLFDWLRQVUHIHUWR³ OPTICAL
COMMUNICATIONS´
³ ´ 'LVSOD\DGMXVWPHQWRIPDLQDPSOL¿HU DQG
VXEDPSOL¿HUVFDQEHFRQGXFWHG
6HWWRWKHWDUJHWYDOXHRIGLVSOD\DGMXVW-
PHQWLQHDFKDPSOL¿HU
³ ´
,QFLGHQWOLJKWLQWHQVLW\RIPDLQDPSOL¿HUFDQ
EHFRSLHGWRVXEDPSOL¿HU+RZHYHUZKHQ
WKHGLIIHUHQFHEHWZHHQ PDLQ DPSOL¿HU DQG
VXEDPSOL¿HULVELJLWZLOOQRWEHFRSLHG
³ ´
'LVSOD\DGMXVWPHQWRIVXEDPSOL¿HUFDQEHVHWWR2))
'LVSOD\DGMXVWPHQWRIPDLQDPSOL¿HULVQRWVHWWR2))
Do not press down the SET key many times in display
RI³ ´:KHQ³ ´LVQRWGLVSOD\HGLQFRQ-
¿UPDWLRQDOVRGRQRWSUHVVGRZQVHWNH\PDQ\WLPHV
Copy lock
setting
When conducting the setting of copy setting or data bank load-
LQJVDYLQJIURPWKHPDLQDPSOL¿HUYLDRSWLFDOFRPPXQLFDWLRQV
LWLVSRVVLEOHWKDWRQO\WKHVXEDPSOL¿HUZKLFKLV VHW WR FRS\
ORFN21³ ´GRHVQRWUHFHLYHWKHVHWFRQWHQWV
+RZHYHUHYHQLIFRS\ORFNRQ³ ´LVVHWWKHFRS\
action setting is communicated.
Communication
protocol setting
When conducting the copy setting or setting of data bank
ORDGLQJVDYLQJIURPWKHPDLQDPSOL¿HUYLDRSWLFDOFRPPXQL-
FDWLRQVWKHRSWLFDOFRPPXQLFDWLRQVWKURXJKDVXEDPSOL¿HU
ZKLFKLVVHWWRFRPPXQLFDWLRQHPLVVLRQKDOW³ ´
DQGWKHIROORZLQJVXEDPSOL¿HUVFDQEHKDOWHG
([WHUQDOLQSXW
setting 6HWH[WHUQDOLQSXW
Code setting
&RQVLVWHQWVHWWLQJFDQEHGRQHE\LQSXWWLQJGLJLW
code instead of independent setting.
,QDGGLWLRQSUHVHQWVHWWLQJFDQEHFRQ¿UPHG
'LVSOD\DGMXVW-
ment setting
Set incident light intensity to target value.
,IFRQGXFWLQJGLVSOD\DGMXVWPHQWVHWWLQJZKHQLQFLGHQWOLJKW
LQWHQVLW\GRHVQRWKDYHHQRXJKPDUJLQ³ ´LVEOLQNHG
³ ´ 'LVSOD\DGMXVWPHQW2))
³ ´ 6OLGHWRVPDOOHUVLGHLQFLGHQWOLJKWLQWHQ-
sity from the set of target setting.
³ ´
Set incident light intensity to value you want.
,QFDVHVHWWLQJWRDGMXVWPHQWVHWWR
5HVHWVHWWLQJ
-
,IVHWWLQJWR³ ´UHWXUQVWRGHIDXOWVHWWLQJVIDFWRU\VHWWLQJV
CUSTOM setting
Select an item in CUSTOM mode to display.
Interference pre-
vention setting
Number of adherence mounting of sensor head depends
on response time of interference prevention function.
)RUGHWDLOUHIHU³ INTERFERENCE PREVENTION FUNCTION."
³ ´
Set when using the interference prevention
IXQFWLRQE\RSWLFDOFRPPXQLFDWLRQ0D[LPXP
adherence mounting of sensor head is 12 units
³ ´
Set when using interference prevention
function by changing emitting frequency.
7KHPD[LPXPDGKHUHQFHPRXQWLQJby set-
WLQJW\SHVRIHPLVVLRQIUHTXHQF\LVXQLWV
Sensing output
mode
Set sensing output 1 mode and sensing output 2 mode.
³ ´1RUPDOPRGH
Sets a threshold value for ON / OFF operation.
³ ´:LQGRZFRPSDUDWRUPRGH
([FHSWVHQVLQJRXWSXW
6HWVWZRWKUHVKROGYDOXHVDQGMXGJHVWKH\DUHZLWKLQWKHUHTXLUHG
UDQJHRUQRW7KLVFDQEHVHOHFWHGLQSRLQWWHDFKLQJ
³ ´5LVLQJGLIIHUHQWLDOPRGH
Only drastic rises in incident light intensity are detected.
³ ´7UDLOLQJGLIIHUHQWLDOPRGH
Only drastic drops in incident light intensity are detected.
³ ´+\VWHUHVLVPRGH
Changes hysteresis to ignore small change of inci-
dent light intensity.
7KLVFDQEHVHOHFWHGLQSRLQWWHDFKLQJ
³ ´6HOIGLDJQRVLVRXWSXWPRGH
([SHFWVHQVLQJRXWSXW
Conduct self diagnosis output
³ ´)RUFHG21RXWSXWPRGH
Sets forcibly the output to ON.
³ ´)RUFHG2))RXWSXWPRGH
Sets forcibly the output to OFF.
•
•
•
•
•
•
•
•
•
Logical
operation
setting
Select for logical operation and set logical operation methods
DQGRU[RU
³ ´
Logical operation is sensing output 2 of this device
and conduct logical operation between the sensing
output 2 and sensing output 1 of this device.
³ ´
Logical operation is sensing output 1 of an
XSSHUDGMDFHQWDPSOLILHUDQGFRQGXFWORJLFDO
operation between the sensing output and
sensing output 1 of this device.
³ ´/RJLFDORSHUDWLRQLVRXWHULQSXWDQGFRQGXFW
logical operation between the output and
sensing output 1 of this device.
Logical
operation
Sensing
output 1 of
this device
Setting of logical operations
and or [RU
ON ON ON ON OFF
ON OFF OFF ON ON
OFF ON OFF ON ON
OFF OFF OFF OFF OFF
6HWWLQJRIWKUHVKROGYDOXHWUDFNLQJ!
Threshold tracking is OFF
Select threshold tracking cycle in the
UDQJHRIWRVHF
Tracks threshold when the output is OFF
Tracks threshold when the output is ON
1RWVWRUHGLQ((3520
Select the cycle of storage in EE-
3520LQWKHUDQJHRIWRWLPHV
Limit teaching
Auto teaching
352!
352!
Sensing
output setting
Setting of
threshold
value tracking
Setting of
threshold
tracking cycle
Storage
cycle setting
(OFF)
(OFF)
(OFF)
Algorithm
setting
Limit
teaching
Logic opera-
tion setting
Item Default
setting Description
Setting of
threshold value
tracking
This mode can change the threshold value depending
RQWKHF\FOHWRVHFWKDWLVVHWZLWKWKHYDULD-
tions of the incident light intensity. The tracking shift
amount is the one which is set at the shift setting.
Sensing
output setting
Selects whether tracking threshold when the output is
OFF or when the output is ON.
Storage cycle
setting
6HOHFWVDWKUHVKROGVWRUDJHF\FOHLQ((3520IURP
to 250 times.
Algorithm
setting
1RWH
When setting to limit teaching, threshold value is fol-
lowed up on the bases of shift amount. Furthermore,
when setting to auto teaching, threshold value be fol-
lowed up on the bases of each cycle
1RWHV &RQGXFWVWKHOLPLWWHDFKLQJIRUWKHFKDQJHGLQFLGHQWOLJKWLQWHQVLW\
Shift direction of the threshold differs depending on the combination of the sensing
output status and the sensing output operation.
Sensing output status Sensing output operation Shift direction
Sensing output ON Light-ON
-
Sensing output ON Dark-ON +
Sensing output OFF Light-ON +
Sensing output OFF Dark-ON
-
&RGHVHWWLQJWDEOH
*UHHQGLJLWDOGLVSOD\ULJKWVLGHLVWKH¿UVWGLJLW
Code
Forth digit
Code
Third digit
Code
Second
digit
Code
First digit
Sensing output opera-
tion mode Timer operation Timer
period
CUSTOM
setting
Sensing
output 1
Sensing
output 2
Sensing
output 1
Sensing
output 2
Light-ON Light-ON No timer No timer 0.5ms
5HVSRQVH
time setting
Light-ON Dark-ON OFD No timer 1ms
Emission
power setting
Dark-ON Light-ON OND No timer PV Hysteresis
setting
Dark-ON Dark-ON ONOF No timer 5ms
OSD No timer 10ms
ONOS No timer PV
No timer OFD 50ms
No timer OND 100ms
No timer OSD PV
500ms
1 sec.
2 sec.
VHF
4 sec.
5 sec.
OFD: OFF-delay timer, OND: ON-delay timer
ONOF: ON / OFF-delay timer, OSD: One-shot timer,
ONOS: ON-delay / One-shot timer
5HGGLJLWDOGLVSOD\ULJKWVLGHLVWKH¿UVWGLJLW
Code
Forth digit
Code
Third digit
Code
Second
digit
Code
First digit
Copy lock
setting
Hysteresis
setting
Setting items
in digital dis-
play setting
Back up
setting
5HVSRQVH
time setting
Sensing
output
mode
(Note)
Copy lock
OFF H-02 Incident light
intensity
Back up ON
H-SP Normal
mode
Copy lock
ON H-02 Incident light
intensity
Back up OFF
FAST
WC mode
Copy lock
OFF + Displayed in
percentage
Back up ON
STD
5LVLQJGLIIHU-
ential mode
Copy lock
ON + Displayed in
percentage
Back up OFF
LONG
Trailing differ-
ential mode
Copy lock
OFF H-01 Peak / bot-
tom value
Back up ON
U-LG HYS mode
Copy lock
ON H-01 Peak / bot-
tom value
Back up OFF
+<3(5
(WC mode: Window comparator mode, HYS mode: Hysteresis mode)
Note: It is a setting only for sensing output 1. Sensing output 2 is not set.
Ɣ
Ɣ
13
ERROR INDICATION
In case of errors, attempt the following measures.
Error in-
dication
Description 5HPHG\
((3520LVEURNHQRUUHDFKHG
the end of its working life. 3OHDVHFRQWDFWRXURI¿FH
((3520ZULWLQJHUURU
Load of the sensing output 1 is short-
FLUFXLWHGFDXVLQJDQRYHUFXUUHQWWRÀRZ
Turn OFF the power and check the
load.
Load of the sensing output 2 is short-
FLUFXLWHGFDXVLQJDQRYHUFXUUHQWWRÀRZ
Communication error when the
DPSOL¿HUVDUHPRXQWHGLQFDVFDGH
Verify that there is no loose or clear-
DQFHEHWZHHQDPSOL¿HUV
Communication error between the
upper communication unit and
DPSOL¿HUV
Verify that there is no loose or clear-
ance between the upper communication
XQLWDQGDPSOL¿HUV
14
OPTICAL COMMUNICATION
When the setting of data bank loading / saving, copy setting, or copy ac-
tion setting is conducted via optical communications, cascade the sub
DPSOL¿HUVULJKWVLGHWRWKHPDLQDPSOL¿HUDVIROORZV
,IDQDPSOL¿HULVXQGHUDQ\RIWKHIROORZLQJFRQGLWLRQVWKHVHWWLQJRIGDWD
bank loading / saving, or copy setting cannot be carried out .
&RS\ORFNVHWWLQJLVVHWWRFRS\ORFN21³ ´
Digital display is blinking
When communication protocol of a sub amplifier is set to communication
HPLVVLRQKDOW³ ´ WKHVHWWLQJRI GDWDEDQNORDGLQJVDYLQJRU
FRS\VHWWLQJFDQQRWEHFDUULHGRXWWRVXEDPSOL¿HUVVXEVHTXHQWWRWKHPHQ-
WLRQHGDPSOL¿HU
Make sure to mount closely like follows since interference prevention
function is conducted by optical communication.
:KHQWKLVSURGXFWDQGRWKHUSURGXFWVHJ¿EHUVHQVRUDPSOL¿HUVSUHV-
sure sensor controllers, etc.) are connected together in cascade, install
those products so that they are in order of Group A, B, C, and D as
VKRZQLQWKHULJKW¿JXUH7KLVSURGXFWLVLQFOXGHGLQ*URXS'
Group Model No.
AFX-301Ƒ&RQYHQWLRQDOYHUVLRQXQLW
FX-301BƑGƑHƑLS-401Ƒ
BFX-301Ƒ0RGL¿HGYHUVLRQXQLW
FX-305ƑFX-301Ƒ-C1
CLS-403ƑDPS series
DFX-500 series
$VIRUWKH SURGXFWVWKDWDUHORFDWHGEHWZHHQGLIIHUHQWJURXSVDI¿[ WKH
DPSOL¿HUSURWHFWLRQVHDOFX-MB1 (optional) on the communication win-
dow of each corresponding product.
Within each group, identical models should be connected in a lump.
:KHQWKLVSURGXFWDQGRWKHUSURGXFWV¿EHUVHQVRUDPSOL¿HUVSUHVVXUH
sensor controllers, etc.) are connected together in cascade, items that
can be copied at Copy setting are limited.
&RSLDEOHLWHPVDUH 'LJLWDOGLVSOD\VHWWLQJLQ581PRGH(&2VHWWLQJ
time period hold setting and CUSTOM setting.
In case conducting copy setting of this device and other FX-500 series
together, functions which are incorporated in this device will be copied
but functions which are not incorporated in this device will not be copied.
This device can not copy the threshold value.
Ɣ
Ɣ
Ɣ
•
•
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
6XEDPSOL¿HUV
0DLQDPSOL¿HU
Communication direction
Communication direction
Group
A
Group
B
Group
D
Group
C
15
INTERFERENCE PREVENTION FUNCTION
This device incorporates an interference prevention function by setting
different emitting frequencies different from an interference prevention
function by optical communication.
For setting, refer to < PRO5: Interference prevention function>LQ³
PRO MODE”.
Possible number of amplifiers for interference prevention function is
different as shown in table below.
5HVSRQVHWLPH
Interference
prevention function setting
H-SP FAST STD LONG U-LG +<35
02412
In case putting in more amplifiers than limit of interference prevention
IXQFWLRQSXWWKH DPSOL¿HUSURWHFWLRQVHDO WRDPSOL¿HUZKLFKLVDGMDFHQW
of end of an amplifier that the interference function is valid or set
2))LQFRPPXQLFDWLRQ SURWRFROVHWWLQJRIWKHHQGRIDPSOL¿HUWKDWWKH
interference prevention function is valid.
For comunicaton protocol setting procedure, refer < PRO4: communication
SURWRFROVHWWLQJ!LQ³ PRO MODE.´
([DPSOHSXWWLQJLQ RIWKLVGHYLFHDQGVHW67'RIUHVSRQFHWLPH
setting.
Possble number of interference prevantion is 4. Put the amplifier
SURWHFWLRQVHDOVWK DQGWKDPSOLILHUVDQGEHWZHHQWKDQGWK
DPSOL¿HUVRUFDKQJWKHFRPPXQLFDWLRQSURWRFROVHWWLQJRIWKDQGWK
to OFF since interference prevention works from 1st to 4th, from 5th
WRWKDQGWKWRWK
,QFDVHPRXQWLQJPRUHDPSOL¿HUVZKRVHUHVSRQVHWLPHVHWWLQJDUHGLIIHU-
HQWSXWSURWHFWLRQ VHDOEHWZHHQDPSOL¿HUV WKDWKDYHGLIIHUHQWUHVSRQVH
WLPHVHWWLQJRUVHWFRPPXQLFDWLRQSURWRFROVHWWLQJRIWKHXSSHUDPSOL¿HU
to OFF.
For communication protocol setting procedure, refer to < PRO4: communication
SURWRFROVHWWLQJ!LQ³ PRO MODE.´
16
CAUTIONS
This product has been developed / produced for industrial use only.
Make sure that the power supply is OFF while adding or removing the
DPSOL¿HUV
7DNHFDUHWKDWLIDYROWDJHH[FHHGLQJWKHUDWHGUDQJHLVDSSOLHGRULIDQ$&
power supply is directly connected, the product may get burnt or damaged.
Take care that short-circuit of the load or wrong wiring may burn or dam-
age the product.
Do not run the wires together with high-voltage lines or power lines, or
put them in the same raceway.
This can cause malfunction due to induction.
7KHVSHFL¿FDWLRQPD\QRWEHVDWLV¿HGLQDVWURQJPDJQHWLF¿HOG
Verify that the supply voltage variation is within the rating.
If power is supplied from a commercial switching regulator, ensure that the frame
ground (F.G.) terminal of the power supply is connected to an actual ground.
In case noise generating equipment (switching regulator, inverter mo-
tor, etc.) is used in the vicinity of this product, connect the frame ground
(F.G.) terminal of the equipment to an actual ground.
7KHXOWUDORQJGLVWDQFH8/*+<35PRGHLVPRUHOLNHO\WREHDIIHFWHG
E\H[WUDQHRXVQRLVHVLQFHWKHVHQVLWLYLW\RIWKDWLVKLJKHUWKDQWKHRWKHU
modes. Make sure to check the environment before use.
Do not use during the initial transient time (H-SP, FAST, STD: 0.5 sec.,
/21*8/*+<35VHFDIWHUWKHSRZHUVXSSO\LVVZLWFKHG21
Make sure to use the quick-connection cable (optional) for the connec-
tion of the controller.
([WHQVLRQXSWRWRWDOPLVSRVVLEOHZLWKPP2or more, cable.
However, in order to reduce noise, make the wiring as short as possible.
Make sure that stress by forcible bend or pulling is not applied to the
VHQVRUFDEOHMRLQWDQG¿EHUFDEOH
This product is suitable for indoor use only.
Avoid dust, dirt, and steam.
Take care that the product does not come in contact with oil, grease, or-
ganic solvents such as thinner, etc., strong acid or alkaline.
7KLVSURGXFWFDQQRW EHXVHGLQDQHQYLURQPHQWFRQWDLQLQJLQÀDPPDEOH
RUH[SORVLYHJDVVHV
Never disassemble or modify the product.
7KLVSURGXFWDGRSWV ((35206HWWLQJVFDQQRW EHGRQH WKRXVDQG
WLPHVRUPRUHEHFDXVHRIWKH((3520¶VOLIHWLPH
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
•
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Communication direction
17
SPECIFICATIONS
Type Series connection type
NPN output PNP output
Item
Model No.
FX-502
FX-502P
Supply voltage WR9'&5LSSOH33RUOHVV
Power consumption
1RUPDORSHUDWLRQP: RU OHVVFXUUHQW FRQVXPSWLRQ
40mA or less at 24V supply voltage)
(FRPRGHP:RUOHVVFXUUHQWFRQVXPSWLRQP$RU
less at 24V supply voltage)
Sensing output
<NPN output type>
NPN open-collector transistor
0D[LPXPVLQNFXUUHQW
50mA (Note 1)
$SSOLHGYROWDJH9'&RUOHVV
(Between sensing output and 0V)
5HVLGXDOYROWDJH
2V or less (Note 2)
>$WP$1RWHVLQNFXUUHQW@
•
•
•
<PNP output type>
PNP open-collector transistor
0D[LPXPVRXUFHFXUUHQW
50mA (Note 1)
$SSOLHGYROWDJH9'&RUOHVV
(Between sensing output and +V)
5HVLGXDOYROWDJH
2V or less (Note 2)
>$WP$1RWHVRXUFHFXUUHQW@
•
•
•
Output operation Switchable either Light-ON or Dark-ON
Short-circuit
protection
Incorporated
5HVSRQVHWLPH
+63ȝVRUOHVV)$67ȝVRUOHVV67'ȝVRUOHVV
/21*PVRUOHVV8/*PVRUOHVV+<35PVRUOHVV
Selectable
([WHUQDOLQSXW
Signal condition
+LJK9WR9'&RU2SHQ
Low:
0 to +1.2V DC
(at 0.5mA source current)
,QSXWLPSHGDQFH$SSUR[Nȍ
•
•
Signal condition
High:+
4V to +V DC
DWP$VLQNFXUUHQW
Low: 0 to +0.6V DC or Open
,QSXWLPSHGDQFH$SSUR[Nȍ
•
•
Timer function
Changeable in OFF-delay, ON-delay, One-shot timer, ON /
OFF-delay or ON-delay / One-shot timer
7LPHUSHULRG!
Time period depends on timer range
:KHQXVLQJWKHWLPHUUDQJH³PV´VHWWLQJ
$SSUR[PV$SSUR[WRPV
:KHQXVLQJWKHWLPHUUDQJH³VHF´VHWWLQJ
$SSUR[VHF$SSUR[WRVHF
:KHQXVLQJWKHWLPHUUDQJH³PV´VHWWLQJ
$SSUR[PV$SSUR[WRPV
Interference prevention
function
,QFRUSRUDWH1RWH
Ambient
temperature
WR&,IWRXQLWV DUH PRXQWHG LQFDVFDGH WR
&RULIWRXQLWVDUHPRXQWHGLQFDVFDGHWR&
(No dew condensation or icing allowed)
Storage:
-
WR&
Ambient humidity WR5+6WRUDJHWR5+
Material Enclosure: Heat-resistant ABS, Switch: TPEE
Operation key cover: Polycarbonate
Weight (Main body only)
$SSUR[J
Accessory
FX-MB1$PSOL¿HUSURWHFWLRQVHDOVHW
1RWHV P$PD[LIRUPRUHVHULHVFRQQHFWLRQW\SHVDUHFRQQHFWHGWRJHWKHU
2) In case of using the quick-connection cable (cable length 5m) (optional).
,QWHUIHUHQFHSUHYHQWLRQIXQFWLRQGHSHQGVRQUHVSRQVHWLPHDVIROORZ
)RUGHWDLOVUHIHUWR³ INTERFERENCE PREVENTION FUNCTION´
7KHFDEOHIRUDPSOL¿HUFRQQHFWLRQLVQRWVXSSOLHGDVDQDFFHVVRU\%HVXUHWRXVH
the optional cables given below.
<Series connection connector type>
Cable
Cable length 1m Cable length 2m Cable length 5m
Main cable Sub cable Main cable Sub cable Main cable Sub cable
);Ƒ CN-74-C1 CN-72-C1 CN-74-C2 CN-72-C2 CN-74-C5 CN-72-C5
18
INTENDED PRODUCTS FOR CE MARKING
7KHPRGHOOLVWHG XQGHU³ SPECIFICATIONS´FRPHVZLWK
CE Marking.
$VIRUDOORWKHUPRGHOVSOHDVHFRQWDFWRXURI¿FH
Ɣ
Interference
prevention
possible
range
Put a protection seals between
WKDQGWKDPSOL¿HU
Or set communication protocol
setting in 4th to OFF.
Put a protection seals between
WKDQGWKDPSOL¿HU
Or set communication protocol
VHWWLQJLQWKWR2))
Interference prevention
possible range
Interference prevention
possible range
Table of contents
Other Sunx Amplifier manuals
