SUP’AIR KINDER 2 User manual

SUPAIR SAS
PARC ALTAÏS
34 RUE ADRASTÉE
74650 ANNECY CHAVANOD
FRANCE
RCS 387956790
KINDER 2
Indice de révision : V1 09/02/2021
User’s manual
English

KINDER 2 page 2
Harness User’s manual | KINDER 2 Thank you for choosing the Kinder 2. We
are glad to be able to share our common
paragliding passion with you.
SUPAIR has been designing, producing and
selling free flying equipment since 1984. By
choosing a SUPAIR product you benefit from
almost thirty years of expertise, innovation
and listening. This is also our philosophy :
working endlessly to develop better pro-
ducts and to maintain a high quality produc-
tion.
We hope you will find this user’s manual
comprehensive, explicit and hopefully en-
joyable as well. We advise you to read it ca-
refully.
You will find the latest up to date information
about this product on our website
www.supair.com.
If you have any further questions, feel free
to ask one of our retailers for answers. And
naturally, the entire SUPAIR team is at your
disposal on [e-mail].
We wish you many safe enjoyable flying
hours, and happy landings
Team SUPAIR

KINDER 2 page 3
Harness User’s manual | KINDER 2
Introduction 4
Technical specifications 5
Size choice 6
Components list 6
Harness Overview 7
Accessories assembly 8
Seat plate 8
Carabiners 8
Bumpair 9
Adjustments 10
The various adjustments 10
Adjusting the harness 11
Spreader bars/harness Connection 12
Flight phases 13
Pre-Flight check 13
Take-off 13
In flight 13
Landing 14
Towing 14
Mandatory controls 14
In case of an incident 15
Maintenance 16
Harness cleaning and maintenance 16
Storage and transport 16
Product longevity 16
Repairs / spare parts 17
Materials 17
Recycling 17
Warranty 18
Disclaimer 18
Pilot’s gear 18
Service Book 19
LIST OF CONTENTS

KINDER 2 page 4
Harness User’s manual | KINDER 2 INTRODUCTION
Conseil. Attention ! Danger !!
Welcome to the world of paragliding according to SUPAIR, a world of shared passion.
This harness has all the makings of a great one. However, it is a passenger tandem harness
and not a solo harness: your presence as a pilot and your knowledge of tandem flying are re-
quired.
Please also observe the flying and insurance regulations for tandem flights applicable in your
country.
The well though-out design and choice of materials were guided by the same quality and du-
rability objectives.
The KINDER 2 harness was certified EN 1651: 2018 and LTF Nfl II 91/09. Indicating that it
meets European and German safety requirements.
After reading this manual, we suggest you to check your harness in static hang-posts to adjust
it before your first flight.
N.B : Three important icons will help you when reading this manual :

KINDER 2 page 5
Harness User’s manual | KINDER 2
Harness size Unique
Pilot size (cm) 100 - 150
Pilot weight (mini - maxi) (kg) 20 - 60
Harness weight (+ carabiners+speedbar)(kg) 1,95 kg
Designed for Paragliding only
ABack lenght (cm) 58
BBackrest tilt adjustment (cm) 33
CSeat length (cm) 28
DSeat width (cm) 34
ECarabiners height (cm) 34 / 49
FCarabiners distance (cm) 32- 42
Back protection BUMPAIR
Certification EN 1651 - LTF
Maximum in flight weight ( certification ) 80 kg
Tandem (Pilot or Passenger) Yes
Aerobatic flying No
Towing Yes
Reserve parachute No
A
B
C
D
EF
A
B
C
D
E
F
TECHNICAL SPECIFICATIONS
Back lenght
Backrest tilt adjustment
Seat length
Seat width
Carabiners height
Carabiners distance

KINDER 2 page 6
Harness User’s manual | KINDER 2
1
2
3
4
2
1
3
4
BUMPAIR 15 KD2
SIZE CHOICE
The KINDER 2 is available in one size.
It covers an age range from 6 to 12 years, but as children vary greatly in size and build at these ages, it is advisable to
try it out under a gantry before purchase.
COMPONENTS LIST
Polypropylene seat plate
Harness
2x 30 mm Zicral self-locking cara-
biners

KINDER 2 page 7
Harness User’s manual | KINDER 2
1
2
3
4
5
Chest strap adjustment
2
Back storage pocket
1
5
4
3
Shoulder strap adjustment
Backrest angle adjustment
Main hooking points
HARNESS OVERVIEW

KINDER 2 page 8
Harness User’s manual | KINDER 2
KD2 Seat plate polypropylène
Réf. :MPPL034
Installing the seatplate :
30 mm Self-locking zicral carabiners
Réf. : MAILCOMOUS30
Insert the carabiner through the
main harness riser connection.
ACCESSORIES ASSEMBLY
Compatible carabiners :
Seat plateCarabiners
Front
Rear
Flight direction
1. Turn over the seat
2. Slide the plate under the seat, being careful to put the leg straps be-
hind the plate

KINDER 2 page 9
Harness User’s manual | KINDER 2
BUMPAIR
ACCESSORIES ASSEMBLY
Insert the bumpair behind the seat.

KINDER 2 page 10
Harness User’s manual | KINDER 2
1
2
3Chest strap adjustment
1
2
3
ADJUSTING THE HARNESS
Important : Adjusting the harness prior each takeoff is vital.
The various adjustments
Adjusting the shoulder straps
Adjusting the backrest

KINDER 2 page 11
Harness User’s manual | KINDER 2 ADJUSTING THE HARNESS
Without strap tension, first adjust the backrest incline at the desired angle.
- Tightening will bring the backrest at a more vertical angle ( recommended posture for beginners ).
- Loosening the backrest will tilt the back support rearward.
Adjusting the harness
tighten
loosen
Adjusting the chest strap :
The distance to consider corresponds to the length between the middle points at the bottom of each carabiner.
The ideal distance varies between paragliding wing models.
Adjust your harness’s chest strap according to the wing manufacturer’s recommendations.
Adjust the shoulder straps length using the trimmers
The pressure on the shoulder straps contributes to general comfort in flight. It must be pre-
cise: not too tight nor too loose. The upper area of the straps must offer enough support to
maintain your torso in a comfortable position.
Tightening the chest-strap provides more stability but less piloting efficiency while increasing
the risk of riser twisting.
On the contrary loosening the strap provides more efficiency but can be dangerous in turbu-
lent aerology (increased risk of falling towards the collapsed side of your glider).
To get a “standard” adjustment, the two red marks located on the Safe-T-Bar and on the chest
adjustment strap should be matched together.
tightenloosen

KINDER 2 page 12
Harness User’s manual | KINDER 2 CONNECTING THE WING TO THE HARNESS
Soft spreader bars positionRigid spreader bars position

KINDER 2 page 13
Harness User’s manual | KINDER 2
• Lock the buckles carefully.
FLIGHT PHASES
Once up in the air, the KINDER 2 behaviour is stable and instinctive.
In flight
• Check that the harness, the carabiners, the spreader bar and in general all your flight equipment are not damaged. As the captain, you
are responsible for the safety of the crew
• Check that your personal settings haven’t changed.
• Check that all zippers and buckles are closed.
• Make sure that the self-locking carabiners are locked and connected to the paraglider.
Pre-Flight control
Take-off
After a thorough weather conditions analysis, when the decision to fly has been taken, put your harness on and follow the next steps
Takeoff maintaining a vertical posture and push yourself inside the harness but only once away
from the ridge.
Do not release your hands from the brakes when you are close to terrain.

KINDER 2 page 14
Harness User’s manual | KINDER 2
Straighten yourself in your harness and adopt a running posture to dissipate the horizontal speed.
Always be certain to have enough altitude to make a landing approach corresponding to the weather conditions of the moment and ter-
rain. During the landing approach, never make hasty maneuvers. Always land upwind in a standing posture and be ready to run upon
touchdown if necessary.
During your final approach, use as much airspeed as possible based on the weather conditions of the moment, then gradually reduce the
glider air speed by pushing the toggles all the way down until contact with the ground is made. Beware not to brake too soon and too rapidly
and too deep which could lead to a stall and a dangerous landing.
During high wind speed landings, turnaround and face the wing as soon as ground contact is made and move toward the wing while brak-
ing symmetrically to deflate it. Do not land in a seated position as it is dangerous.
FLIGHT PHASES
Landing
TOWING
To takeoff under tow, you must be equipped with a quick release specially designed for the task.
Connect the tow bridle to the wing riser loops with a suitable tow bridle. Installation must follow the tow bridle reales manufacturer’s recommenda-
tions. Before towing, you should consult with a competent towing outfit about safety recommendations.

KINDER 2 page 15
Harness User’s manual | KINDER 2 IN CASE OF AN INCIDENT
Call for help after an accident
Flashlight SOS :
112EUROPE / INDIA
911
USA / CANADA
119CHINA / JAPAN
101NEPAL
112IRAN
000AUSTRALIA
111NEW ZEALAND
Help needed?
Emergency call
numbers
YES NO

KINDER 2 page 16
Harness User’s manual | KINDER 2 CARE
It is a good idea to clean your harness from time to time. We recommend using a brush and soft solvents only ( soap or mild cleaning agents ). Rinse
thoroughly. Never use aggressive chemicals such as strong solvents which could be harmful to the harness’s fabric, webbings, stitching and weaken
its integrity.
The zip fasteners should be lubricated from time to time, using a silicon spray.
If you regularly use your harness in a dusty environment ( dirt, sand, etc... ), we advise you to regularly check and maintain your carabiners and buck-
les: clean them with a mild detergent, then blow dry them fully but DO NOT LUBRICATE!
Prior to using them, conduct a thorough carabiners and buckles checkup to insure their full functionality.
If you use your harness in a marine/sandy/salty environment, pay particular attention to your gear and follow a rigorous care/maintenance routine.
The threads and fabric used for the manufacturing of the KINDER 2 were specifically selected for their quality and resilience levels. Howe-
ver, in particular instances such as long term UV exposure, abrasion, contact with damaging chemicals, general wear and tear, the harness
will need to be inspected at a professional certified repair facility. Safety comes first!
The self-locking carabiners are NEVER to be used for any activities other than paragliding.
When not in use, your harness should be stored inside your paragliding backpack, in a dry, cool and clean place, protected from UV exposure. If your
harness is wet, please dry it thoroughly before storing.
For transport, protect the harness from any mechanical or UV deterioration (use a bag). Please avoid long transports in wet conditions.
Once every two (2) years, a thorough harness inspection must be conducted :
• Webbing wear and tear (no excessive wear, no rip beginning, no unwanted folds)
• Buckles and carabiners ( functionality, wear and tear ).
Harness cleaning and maintenance
Storage and transport
Life span
Supair advice to replace the carabiners and spreader bars every 5 years or after 500 hours of use.

KINDER 2 page 17
Harness User’s manual | KINDER 2
Fabrics
N/210D 3line Honey Comb
Robic New Lite
Stretch Aquatech
Webbings
Polyester 25 mm (1250 daN)
Polyamide 10 mm
Seat plate
KD2 Polypropylène
- Self-locking zicral 30mm carabiners (référence : MAILCOMOUS 30)
- Polypropylene seat plate ( KD2 : MPPL034 )
- Bumpair 15 KD2
Hardware & Parts
SUPAIR now offers an extended warranty period reaching beyond the product standard protection plan against manufacturing defects.
Please contact us either by telephone or by e-mail [e-mail] in order to receive a quotation..
In spite of using the highest quality products to manufacture the KINDER 2, it is possible for your harness to deteriorate through general use. If show-
ing any sign of wear and tear, it should be sent for inspection and/or repairs at a professional certified facility.
CARE
Repair
Materials
We have minimized our manufacturing footprint by carefully selecting environmentally friendly materials; most of our components are recyclable.
If you estimate that your KINDER 2 has reached the end of it life span, you can separate plastics from metals and recycle them according to your com-
munity rules in effect. As for the fabric itself, contact your local authorities to find out how to proceed to discard it.
Recycling

KINDER 2 page 18
Harness User’s manual | KINDER 2
SUPAIR takes the greatest care in its products design and manufacturing and hence offers a five (5) year limited warranty from the date of purchase
against manufacturing defects or flaws occurring during normal use. Any damage or degradation resulting from incorrect or abusive use, abnormal
exposure to aggressive factors, including, but not limited to; high temperature, intense sun exposure, high humidity etc, will invalidate this warranty.
DISCLAIMER
PILOT’S GEAR
It is essential for you to wear a suitable head protection ( certified paragliding helmet ), boots and right clothing for the activity. Moreover,
carrying a reserve parachute connected to your harness in flight is highly recommend.
WARRANTY
Paragliding is an activity requiring specific skills and sound judgement. Learn how to fly within the environment of a certified paragliding
school. Carry an insurance policy with you in addition to you pilot certification. Always mind and gauge your personal skills relative to the
elements you want to be flying in. Better be safe than sorry ! SUPAIR can not be held responsible for your paragliding decisions or activities.
This SUPAIR product has been designed exclusively for paragliding. Any other activity such as skydiving or BASE jumping is absolutely
forbidden.

KINDER 2 page 19
Harness User’s manual | KINDER 2 SERVICE BOOK
This page will help you keep record of your KINDER 2 scheduled maintenance.
Purchase date
Owner’s name :
Name and stamp of the shop :
Care
Resale
Date
Workshop’s name/ Buyer’s name
Care
Resale
Date
Workshop’s name/ Buyer’s name
Care
Resale
Date
Workshop’s name/ Buyer’s name
Care
Resale
Date
Workshop’s name/ Buyer’s name

SUPAIR-SAS
Parc Altaïs
34 rue Adrastée
74650 Chavanod, Annecy
FRANCE
[e-mail]
[phone]
RCS 387956790