
G@7 Z(25!()0!0#/!*+(%0!$9%3%6!$+4!?0#/!$+4!9322!:/!3%.35/!0#/!4$3%!$2)43%3)4!0+$-&!(*!0#/!$9%3%6A!
[I0/%5!()0!0#/!*+(%0!(*!0#/!$9%3%6!$%5!*(25!5(9%!0#/!.),,(+03%6!2/6!0(!'()+!5/.3+/5!#/36#0!?3*!
).3%6!0#/!03/!5(9%!.0+$,!-(%%/-0!0#3.!%(9L!!
GD7 100$-#!0#/!,/66/5!5(9%!.0+$,!0(!0#/!*+(%0!$9%3%6!,(2/!$%5!2((./2'!036#0/%!
GN7 15\).0!0#/!#/36#0!$%5!.Y)$+/!),!0#/!$9%3%67!M*!:/3%6!2/*0!)%$00/%5/5!(+!30!3.!+$3%3%6L!2(9/+!0#/!
,(2/!#/36#0!0(!$22(9!*(+!9$0/+!+)%!(**7!
GF7 Tighten up both tie down straps
a. (2.5m, 3m or 3.5m versions only) Connect Short Spigot spreader pole to the 1st and 2nd
poles (1st pole is the one closest to the front of the vehicle) To connect the pole, line up the
spigot pin with the hole in the black leg bracket and connect to the 2nd pole (repeat the same
process for the 3m and 3.5m awnings on 2nd & 3rd pole)
b. (2.5m, 3m or 3.5m versions only) tighten up the birds beak spreader rail(s)
c. Insert the roof support poles (C-clip to Foot Cap) push the foot cap in the main aluminium
extrusion track on the awning, then clamp the c-clip section to the adjacent spreader rail
pole(s)
d. Lock off the poles (do not over tighten the roof support as it will appear to distort the
canvas)
e. Tie off the short spigot spreader rail(s) and roof support(s) with the Velcro tabs on the
underside of the awning roof
f. Tighten roof supports further if required
GP7 8/6!5(9%!0#/!*(253%6!*((0!,2$0/.!).3%6!0#/!
93+/!0/%0!,/6.L!-+(..!,/6!0#/!*//0!5(9%!0(!
63;/!.),/+3(+!#(253%6!,(9/+!'(**'For''beach'
or'sandy'setup'we'recommend'using'an'
appropriate'sand'peg)!
!
!
***!If!awning!is!subjected!to!heavy!rain,!either!use!the!provided!rain!tags!or!lower!
poles!one,!three!and!five!?,(2/!]!G!9()25!:/!0#/!,(2/!$0!0#/!;/+'!*+(%0!(*!0#/!$9%3%6L!
,(2/!]F!9()25!:/!$0!0#/!+/$+!(%!$!@7F4!$9%3%6A!this!will!give!the!awning!more!of!a!
roof!pitch!to!allow!the!water!to!drain!off!quickly!to!prevent!damage.***!