Atlantic Ultraviolet Sanidyne PREMIUM User manual

1
Document No. 98-1724B1 • April 2021 • ©2021 Atlantic Ultraviolet Corporation®
Owner’
s Manual
Owner’
s Manual
Amalgam Remote
Controlled Sanitizer
Installation,
Operation &
Maintenance
Read and Follow All
Safety Instructions.
Save These Instructions.
UV
Ultraviolet
Radiation
Protect eyes and
skin from direct and
reflected radiation.
DANGER
!
Manufacturers / Engineers / Sales / Service
Germicidal Ultraviolet – Equipment & Lamps
375 Marcus Boulevard • Hauppauge, NY 11788
[phone] • Fax: [phone]
Email: [e-mail]
Ultraviolet.com • BuyUltraviolet.com
Extensive Product Information Available at:
Ultraviolet.com
BuyUltraviolet.com

2
TABLE OF CONTENTS
SAFETY WARNINGS ....................................................................................................................................................................... 3
SAFETY INSTRUCTIONS .............................................................................................................................................................. 3
Safety LabeLS ................................................................................................................................................................................4
Caution...........................................................................................................................................................................................4
PRODUCT APPLICATIONS ........................................................................................................................................................... 5
ConStruCtion..................................................................................................................................................................................5
PrinCiPLe of oPeration ...................................................................................................................................................................5
LimitationS......................................................................................................................................................................................5
UNPACKING .....................................................................................................................................................................................6
INSTALLATION ...............................................................................................................................................................................6
DimenSionaL Data........................................................................................................................................................................... 6
rear View of unit .........................................................................................................................................................................7
KeyPaD ControLLer oVerView .......................................................................................................................................................7
HanD-HeLD remote ControLLer oVerView .................................................................................................................................8-9
LamP inStaLLation .....................................................................................................................................................................9-10
unit PLaCement ............................................................................................................................................................................10
UNIT OPERATION.........................................................................................................................................................................10
Pre-oPeration ..............................................................................................................................................................................10
Sanidyne®Premium oPeration............................................................................................................................................... 11
uSing tHe KeyPaD ControLLer to Set treatment timeS ............................................................................................................. 11
uSing tHe HanD-HeLD remote ControLLer to Set treatment timeS......................................................................................11-12
Settting Date anD time ...............................................................................................................................................................12
SaVing aSeSSion ...........................................................................................................................................................................12
Determining treatment time for room SizeS .............................................................................................................................13
MAINTENANCE............................................................................................................................................................................. 14
maintenanCe oVerView ................................................................................................................................................................ 14
germiCiDaL LamP inStaLLation, rePLaCement, or CLeaning........................................................................................................14
LamP breaKage ............................................................................................................................................................................14
DiSPoSaL of merCury aDDeD LamP ..............................................................................................................................................14
TROUBLESHOOTING ..................................................................................................................................................................15
TECHNICAL SPECIFICATIONS.................................................................................................................................................15
OPTIONAL ACCESSORIES .........................................................................................................................................................16
REPLACEMENT PARTS...............................................................................................................................................................16
MAINTENANCE LOG..............................................................................................................................................................17-19
USER ASSISTANCE ....................................................................................................................................................................... 20
Patent notiCe...............................................................................................................................................................................20
WARRANTY & PRODUCT REGISTRATION ...........................................................................................................................20
These instructions generally describe the installation, operation and maintenance of the Sanidyne®Premium
Portable Area Sanitizer. Questions that are not specically answerable by these instructions should be directed to
the factory. Atlantic Ultraviolet Corporation® takes all possible precautions when packaging equipment to prevent
damage. Carefully inspect and report all damages. Do not install damaged equipment. Follow all instructions on any
labels or tags. Carefully inspect all packing materials before discarding to prevent the loss of accessories, mounting
hardware, spare parts or instructions.
The information and recommendations contained in this publication are based upon data collected by the
Atlantic Ultraviolet Corporation® and are believed to be correct. However, no guarantee or warranty of any kind,
expressed or implied, is made with respect to the information contained herein. Specications and information
are subject to change without notice.

3
SAFETY INSTRUCTIONS
To guard against injury, basic safety precautions should be observed, including the following:
1. Read and follow ALL safety instructions.
2. Avoid exposure to direct or reected germicidal ultraviolet rays. Germicidal
ultraviolet rays are harmful to the eyes and skin.
3. Intended for indoor use only.
4. Do not alter design or construction.
5. Do not use this sanitizer for other than its intended purpose, as described in this manual.
6. Do not use this sanitizer in occupied areas. The supplied “DANGER - DO NOT ENTER…” sign(s) MUST be clearly
displayed to warn against entering the area during the disinfection cycle without proper personal protection equipment.
7. Germicidal ultraviolet rays may break down plastic, rubber or other non-metallic materials, with
inadequate resistance to ultraviolet. Shield all plastic, rubber or other non-metallic parts which may be exposed to direct or
reected germicidal ultraviolet rays.
8. Do not remove any labels.
9. Do not operate without proper electrical ground.
10. Do not operate the sanitizer if the power cord and/or plug are damaged, or if any other damage to the sanitizer is
visible or suspected.
11. Utility power supplied to the sanitizer, MUST match power requirements listed on the sanitizer label.
12. Always disconnect power to the xture before performing any service or maintenance.
13. Read and follow all notices and warnings on the sanitizer.
14. SAVE THESE INSTRUCTIONS.
SAFETY WARNINGS
• All personnel should be alerted to the potential hazards indicated by the product safety labeling on this unit.
• The following conventions are used to indicate and classify precautions in this manual and on product safety labeling. Failure to
observe precautions could result in injury to people or damage to property.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
This symbol is used to identify the need to wear
protective gloves.
Caution indicates a POTENTIALLY
hazardous situation, which, if not avoided,
MAY result in minor or moderate injury.
Caution used without the safety alert symbol
indicates a potentially hazardous situation, which,
if not avoided, may result in property damage.
Warning indicates a POTENTIALLY
hazardous situation, which, if not avoided,
COULD result in death or serious injury.
This symbol is used to identify an
ULTRAVIOLET LIGHT hazard.
This symbol is used to identify an ELECTRICAL
SHOCK or ELECTROCUTION hazard.
This symbol is used to identify the need to wear
approved ultraviolet blocking eyewear.
This symbol is used to identify the need to wear approved
ultraviolet blocking face shield.
This symbol is used to identify components which must
not be disposed of in trash
Danger indicates an IMMINENTLY
hazardous situation, which, if not avoided,
WILL result in death or serious injury.

4
SAFETY LABELS
Danger Label: Ultraviolet Radiation (70-0052)
DANGER
!
UV
Ultraviolet
Radiation
Protect eyes and
skin from direct and
reflected radiation.
Part No. 00-0358
Danger: UV 5”x5” PMS109, PMS185/ out dr & Bk White Mylar UV Varnish
00-0358
Danger Label: Ultraviolet Radiation (00-0358)
Danger Label: Hazardous Voltage /
Ultraviolet Radiation (70-0036)
CAUTION
It is the user’s responsibility to determine and validate the suitability of this equipment for use in the user’s system or
process. No warranty or representation is made by the manufacturer with respect to suitability or performance of this
equipment or to the results that may be expected from its use. The user should periodically inspect, clean as necessary and
conrm the presence and good legibility of the product safety labels. Contact the factory for replacement labels in the event
that any of the labels are missing or illegible.
Location of Danger Labels (70-0036,
70-0037, and 70-0011) on Back of Unit
Location of Danger Labels (70-0052) on Top of Unit
Location of Danger Labels (00-0358) on Both Sides of Unit
Hg-Lamp Contains Mercury Label (70-0011)
Warning Germicidal UV Label (70-0037)

5
PRODUCT APPLICATIONS
ConstruCtion
The Sanidyne®Premium Germicidal Ultraviolet Portable Area Sanitizer consists of:
• STER-L-RAY ®Amalgam Germicidal Ultraviolet Lamps: Deliver ultraviolet energy at the specic wavelength of 254
nanometers (nm). This wavelength is highly effective against microbes including virus, bacteria and mold spores. Germicidal
ultraviolet rays are harmful to eyes and skin, avoid exposure of direct or reected germicidal ultraviolet rays without approved
ultraviolet blocking face shield and protective covering (such as gloves, long sleeves with no gaps between cuff and gloves).
• Audible Exit Warning Alarm: To alert area that the lamps will be powered on in one minute and thirty seconds after the start
button is pressed or to indicate intruder is in Operation Area.
• Elapsed Time Indicator: A non-resettable display of the operating hours. Useful for scheduling and recording maintenance
and lamp replacement.
• Hand-Held Remote Controller: Provides easy operation of Sanidyne®Premium from a safe distance, displays lamp
operation, controls treatment times and alerts operator with an audible alarm if an intruder enters Operation Area.
• Keypad Controller: Provides easy operation of Sanidyne®Premium and allows the operator a period of time (one minute
and thirty seconds) to leave the Operation Area before treatment begins.
• Intruder Sensors: Delay treatment if the Operation Area is inhabited. Additionally if sensors detect an intruder with less than
30 seconds left before lamps operate, the countdown time will automatically restore back to 30 seconds until area is cleared.
• Four Wheels with Locking Casters: Make moving Sanidyne®Premium easily accomplished for location changes.
• Power Cord: For 120v AC 50/60Hz single-phase standard household current, a NEMA 5-20, three-prong plug is provided for
a properly grounded outlet. (Consult factory for other plug types).
• Stainless Steel Lamp Guard Assembly: Protects lamps from damage during normal operation.
• Stainless Steel Construction: All electronics and wiring are housed in an enclosure constructed of stainless steel, providing
strength and durability in order to withstand most harsh environments.
• Cooling Fans: Circulate cool, clean air to ensure all electronics are operating at optimum temperatures.
• Sanidyne®Premium will operate at 120v 50/60Hz.
PrinCiPle of oPeration
The Sanidyne®Premium design has been carefully conceived to provide direct germicidal ultraviolet exposure for air and
surface disinfection in unoccupied areas to disinfect and prevent areas and surfaces from microorganisms. The ultraviolet
disinfection dosage is a function of time and the intensity, of the ultraviolet radiation to which the air and surrounding surfaces
are exposed.
NOTE: The Sanidyne®Premium should be used as a supplement to your facility’s cleaning and disinfection protocols, not as a
replacement. Follow your facility’s cleaning and disinfection protocols before using the Sanidyne®Premium.
No special room preparation is required prior to treating a room or area with the Sanidyne®Premium — however, target
surfaces must be directly exposed to the UV rays. These rays will not penetrate materials like cloth, paper or ordinary glass,
therefore, it is important to remove items from the direct line of sight that would block or shield the rays from other surfaces. The
Sanidyne®Premium does not generate any harmful byproducts, nor does it leave any residual substances.
It is the user’s responsibility to determine and validate the suitability of the equipment for use in system
or process. No warranty or representation is made by the manufacturer with respect to suitability or performance of this
equipment or to the results that may be expected from its use.
Indoor Use Only – The equipment must be sheltered from exposure to the elements and extremes in
temperature. Temperature range: 40 °F to 95 °F. The user should periodically inspect, clean as necessary and conrm the
presence and good legibility of the Product safety labels. Contact the factory for replacement labels in the event that any of
the labeling is missing or illegible.
The UV Treatment Results achieved are subject to variations in application conditions, it is recommended
that culture tests be performed to conrm desired outcomes.
limitations
• Safety procedures MUST be implemented to prevent ultraviolet exposure of occupants to direct or reected ultraviolet rays.
Exposure to germicidal ultraviolet rays will result in the irritation of the eyes and reddening of the skin.
• Personal protection equipment is required when entering the irradiated space with the germicidal
lamp(s) operating. Personal protection equipment includes skin and eye protection such as gloves, long
sleeves with no gaps between cuff and gloves, and an ultraviolet blocking face shield (included with the
purchase of the Sanidyne®Premium).

6
UNPACKING
IN ORDER TO PERFORM THIS TASK, BE SURE TO WEAR THE FOLLOWING SAFETY
EQUIPMENT: SAFETY GLASSES OR A FACE SHIELD, AS WELL AS GLOVES
• Remove the Sanidyne®Premium from its shipping carton.
• Atlantic Ultraviolet Corporation® takes all possible precautions when packaging this xture to prevent damage. Carefully
inspect the unit, power cord and plug for damage, report all damage immediately. Do not assemble or operate if there is any
damage, visible or suspected.
• STER-L-RAY ®Germicidal Ultraviolet Lamps are packed separately, to ensure maximum protection. Keep the lamps aside
until ready for installation.
• Carefully inspect all packing materials to prevent the loss of accessories, spare parts or instructions.
• Do not discard packing materials until Sanidyne®Premium is assembled, checked and conrmed.
The Sanidyne®Premium Portable Area Sanitizer includes:
• 1 - Eight-lamp xture with power cord - Includes a microprocessor controller with time display and push button controls
• 1 - Hand-Held Remote Controller
• 8 - STER-L-RAY ®Amalgam Germicidal Ultraviolet Lamps (05-0250) with ArmorLite™Protective Coating
• 2 - Promate™ Ultraviolet Blocking Face Shields with Adjustable Headgear
• 1 - Owner’s Manual
• 4 - Promate™ Danger Signs (98-1827)
• 1 - UV-C Dosimeter Card (00-0373 – See “Optional Accessories” on Page 16 for more information.)
INSTALLATION
Figure 1 – Dimensional Data
All specications, dimensional data, etc are approximate and subject to change without notice.

7
KeyPad Controller overview
Figure 3 – Keypad Controller Overview
1. Treatment Time: Displays chosen treatment time which will countdown after start is selected. Flashes with word “PrEP”
during Countdown Time, the word “run” during Treatment Time and “donE” when Treatment Time is completed.
2. Hour Buttons: Up and down buttons are used to select treatment hours between 0 and 24.
3. Minute Buttons: Up and down buttons are used to select treatment minutes between 0 and 59.
4. Start / Stop Button: Begins treatment time countdown, also used to restart unit after an intruder is sensed in Operating Area.
5. Power Indicator: Glows RED when power is applied to unit and will ash during Treatment Time. Flashes rapidly if
occupancy sensor is tripped
Figure 2 – Rear View of Unit
TREATMENT TIME
POWERMINUTESHOURS
START
STOP
Treatment Time
Displays HOURS: MINUTES
1
Hours Button
Up and Down Arrows set
time from 0 to 24 Hours
2
Power Indicator
Glows RED when power
is applied, flashes during
Treatment Time
Start /Stop Button
Used to begin Treatment Time
and Restart unit after Alarm
4
Minutes Button
Up and Down Arrows set
time from 0 to 59 Minutes
3
5

8
Hand-Held remote Controller overview
Figure 4 – Hand-held Remote Controller Overview
General Rule of Selection: Except for the ON/OFF button located on the right side of the Hand-held Remote Controller, all
selections made to this device will require a gentle touch of a short period of time to achieve a response.
1. Charging Port: Charge Hand-held Remote Controller using supplied AC Adapter.
2. Treatment Time: Set treatment time in Hours, Minutes. Hold nger on Treatment Time to select until menu changes
to scroll bar. Scroll the numbers up or down, positioning the times chosen in the center row. When times are positioned
correctly, select DONE on the screen to input your Treatment Time choice.
3. Current Time:Displays current time in Hours, Minutes, Seconds. Can be reset under SETTINGS, however this requires a
PIN Number to do this. (See “Setting Date and Time” on Page 12)
4. Lamp Operation Indicators: Lamp status glows yellow when the lamps are operating correctly. If lamp is not operating the
lamp status will be displayed grey for that lamp.
5. Start Button: Starts treatment cycle time.
Once selected:
a) Remaining Time changes to Countdown Time and begins counting down from 1 minute and 30 seconds to exit area
b) The words “LEAVE AREA” appear on the lower status bar.
c) Alarm on unit begins to sound
d) The word “PrEP” ashes on the Keypad during the Countdown Time, when Treatment Time begins the word “run”
ashes and when the treatment time is completed the word “donE” will appear.
6. Return Button: Brings you back to previous screen (Remote Overview Continued on Page 9)
Lamp operation indicators
illuminate yellow when
lamps are on
Displays current time
Hours : Minutes : Seconds
Used to define treatment
time in Hours :Minutes
Start Button
Return Button
Pause / Continue Button
Settings Button
LampControl
Treatment Time
00:00:00 00:00:00
00000:0011:57:14
Current Time
Start Pause Stop
Remaining Time
Total Op Time
Connecting to SANIDYNE
Lamp Status
2 3 4 5 6 7 81
90%
Displays Remaining Time and
toggles to Countdown Time shown on
Cycle Time Hours : Minutes : Seconds
Begins at (1:29)minutes when pressed
Displays accumulative hours
of all treatment times
Stop or End Button
Status Bar:
• Ready
• Intruder Alert
• Session in Progress
• Session Paused
• Session Resumed
• Session Stopped
• Leave Area
• Connected to SANIDYNE
Treatment Time
Set lamp cycle time hours and minutes
Done
00
01
02
59
00
01
:
Power off Reboot Airplane mode
Airplane mode is OFF
Airplane mode is ON
!
Volume Button
On / Off Button
Home Button
Battery Condition
Charging Port
11
14
15
12
16
8
9
1
10
2
3
4
5
6
7
13

9
7. Pause / Continue Button: Used to pause the treatment time, or to continue the treatment time. This button toggles from the
Pause Icon, which is displayed as two vertical bars to the Continue Icon which is a looping arrow. If pause is selected below
30 seconds during the Countdown, the Countdown time will reset to 30 seconds. If pause is selected during the cycle time the
device will provide an additional 1 minute and 30 seconds of countdown time to leave the area.
8. Home Button: Exit LampControl app.
9. Battery Condition: Displays the charge level of the battery in the hand-held remote. Press on battery symbol to see
percent of change.
10. Settings Button: Contains choices for:
a) Settings: Reset Operating Time or Clear Session Data
b) Set Date/Time: If changing through this menu, you need a PIN. (See “Setting Date and Time” on Page 12.)
c) Sessions: Log of saved sessions
11. Remaining Time: Displays remaining time of treatment and toggles to (Countdown time shown on Treatment in Hours,
Minutes, Seconds) when selected.
12. Volume Button: Adjust volume on Hand-held Remote Controller.
13. ON/OFF Button: Turns the power to the device on or off and can be used to restart the device. To turn on the device, this
button must be pushed in and held for 2 seconds. If the device is on the Home screen, pressing and holding this button
will bring up a menu with choices to: Power Off / Reboot / Airplane Mode; ON – OFF (MUST BE SET TO ON AT ALL
TIMES). Additionally displays three icons at bottom which are Sound Off / Vibrate / Sound On.
14. Total Operation Time:Displays accumulative hours of all treatment times.
15. Stop or End Button: Stop treatment time.
16. Status Bar: Outputs all the conditions of the device
a) Ready
b) Intruder Alert
c) Session in Progress
d) Session Paused
e) Session Resumed
f) Session Stopped
g) Leave Area
h) Connected to Sanidyne®
lamP installation
Always disconnect power to the xture before performing any service or maintenance.
Germicidal lamps are easily damaged. Exercise care when handling lamps.
Step 1 –Remove Top Cover by
removing all hardware and place on
the side to be reinstalled later.
Step 2 –One end of lamp is marked
“INSTALL THIS END DOWN.”
Carefully t this end of the lamp into
the lamp guard assembly rst, as shown.
Step 3 –Carefully align pins on
lamp base to socket holes on
lampholder as shown. (Lamp
Installation Continued on Page 10.)

10
unit PlaCement
• The Sanidyne®Premium is intended for indoor use only. It should be protected from liquid intrusion such as dripping
water, condensation or mist, and used only in a clean, dry location with temperature ranges between 40 °F to 95 °F.
• Electrical power supplied to the Sanidyne®Premium must match power requirements listed on the Sanidyne®Premium.
• The Sanidyne®Premium is intended for use in UNOCCUPIED AREAS ONLY. Under no circumstances
should this sanitizer be permitted to operate with humans, plants, or animals present in the Operation Area.
• The intrusion sensors will detect movement if anyone is in the treatment area and the lamps will be switched off until xture is
reset by pressing the START/STOP button on keypad on the top of the Sanidyne®Premium.
• For maximum efciency the Sanidyne®Premium should be located as centrally as possible, away from the corners of the
treatment area. The Sanidyne®Premium Portable Area Sanitizer is most effective when it is located in the vertical center of
the room and the ultraviolet rays are unobstructed.
UNIT OPERATION
Pre-oPeration
1. Fully charge the Hand-held Remote Controller (Shown in Figure 4). NOTE: Charger provided operates on 100 volt to 240
volts 50/60Hz and has a NEMA 1-15 plug.
2. Once a location has been chosen for the Sanidyne®Premium post Laminated Warning Signs supplied with the Sanidyne®
Premium on all access doors to the area where treatment operation will take place.
It is the users responsibility to post signs, or notices for all personnel and persons in the building or facility
so that they be made aware that the Operation Area is off limits during treatment.
3. Connect the Sanidyne®Premium to a properly grounded outlet power source which matches the power requirements
listed on the Sanidyne®Premium (See Power In location shown on Figure 2- Rear View of Unit)
Approved Promate™ Face Shields (2), are supplied with each unit. Promate™ Face Shield MUST be
worn prior to the next step by the operator as well as anyone else in the operation area. In addition the
operator and anyone present MUST use protective gloves and clothing to protect skin from UV rays.
4. Turn power on using the Power Switch located on the rear of the Sanidyne®Premium (See Power Switch location shown
on Figure 2 - Rear View of Unit). Switch will glow RED when power is on. Once xture receives power, the RED lights
located just below the Occupancy Sensors on the top of the xture will glow RED. (See Occupancy Sensors (4-Total), shown
on Figure 1 - Dimensional Data). This is not a warning, it indicates that the sensors are aware of your presence.
Step 5 –Repeat until all lamps
have been installed.
Step 6 –Once complete, reinstall
Top Cover.
Step 4 –Using the lamp, apply
slight pressure to compress the lower
lampholder, and then pivot the lamp so
it aligns with the top lamp socket. Lamp
should appear straight when it is correctly
in place. Conrm pins are inserted and
that both ends align. As shown above,
adjust each lamp socket if there is any gap
between the lamp base and lamp socket.

11
sanidyne ®Premium oPeration
The Sanidyne®Premium has two methods of controlling the xture; the Keypad Controller (Shown in Figure 3) and the
Hand-held Remote Controller (Shown in Figure 4). These two controls mirror each other; treatment times entered into Keypad
Controller will appear on the Hand-held Remote Controller and vice versa.
using tHe KeyPad Controller to set treatment times
1. Setting Treatment Time on the Keypad is done using the HOURS and MINUTES buttons which is located on the top of the
Sanidyne®Premium. (See Figure 1 for location) Selecting the up or down facing arrows located on the keypad in line with
the HOURS or MINUTES button will either increase or decrease the hours or minutes. The hours can be set between 0 and
24, and the minutes can be set from 1 to 59. (Example of one hour and ve minutes would appear as 01:05 on the Treatment
Time Display). Since the Keypad Controller will no longer be viewable once the treatment time begins, it is recommended that
the Hand-held Remote Controller be fully charged and powered before this time and be in possession of the operator
at all times.
2. Determining the proper treatment times for your specic location can be done by using the “Recommended Treatment Time
for Room Size” chart (Figure 5 on Page 13).
3. Once the choice of time has been displayed on the Keypad controller, select the START/STOP button to begin and leave the
Operation Area immediately. Make sure that the Hand-held Remote Controller is kept in possession of the operator during the
Treatment Time.
Once you select the START/STOP button an audible exit alarm will begin to sound and the Sanidyne®Premium
will begin counting down from 1:30 seconds to allow all inhabitants to leave the area before the UV treatment begins.
Additionally, the word “PrEP” will begin ashing on the Keypad and the Occupancy Sensors located on the top of the unit
(Shown on Figure 1) will begin to operate at this time, providing an additional safety area around the unit. As an additional
safety feature, if the sensors detect movement close to the Sanidyne®Premium when less than 30 seconds remain on the
countdown time, the Sanidyne®Premium will automatically reset giving 30 seconds more to leave the Operation Area.
Occupancy Sensors do not protect the entire Operation Area of the Sanidyne®Premium. Under no
circumstances should this sanitizer be permitted to operate with humans, plants, or animals present in the Operation Area.
4. Outside the Operation Area the Treatment Time can be viewed on the Hand-held Remote Controller. Once the treatment time
has expired the Sanidyne®Premium will turn off the STER-L-RAY ® Germicidal Ultraviolet Lamps and it is now safe to
return to the area. The word “donE” will begin ashing on the Keypad Controller on the top of the xture.
using tHe Hand-Held remote Controller to set treatment times
The Hand-held Remote Controller provides further detailed information on the Sanidyne®Premium. Therefore it is
recommended to review the Hand-held Remote Controller Overview section of this manual to become familiar with the display
which is shown in Figure 4.
The Hand-held Remote Controller can operate the Sanidyne®Premium remotely, thus it is
imperative that the operator make a visual inspection of the Operation Area to ensure it is clear of all humans, plants, or
animals before proceeding.
1. Setting Treatment Time on the Hand-held Remote Controller is done by holding a nger on the display face, directly on the
words Treatment Time until the screen changes to a scroll bar. Next scroll the numbers up or down, characters on the left are
hours, characters on the right are minutes. Positioning the desired treatment time in the center row. (Example of one hour and
ve minutes would appear as 01:05 on the Treatment Time Display) When times are positioned correctly, select DONE on the
bottom of the scroll bar to input your Treatment Time choice.
2. Determining the proper treatment times for your specic location can be done by using the “Recommended Treatment Time
for Room Size” chart (Figure 5 on Page 13).
3. Once the choice of time has been displayed on the Hand-held Remote Controller, select the start button to begin and leave the
Operation Area immediately. Make sure that the Hand-held Remote Controller is kept in possession of the operator during the
Treatment Time. (Remote Controller Instructions Continued on Page 12)

12
NOTE: Once you select the start button an audible exit alarm will begin to sound and the Sanidyne®Premium will begin
counting down from 1:30 seconds to allow all inhabitants to leave the area before the UV treatment begins. The words
“Leave Area” will now appear on the lower status bar of the Hand-held Remote Controller. (See Figure 4, for the specic
location). The Occupancy Sensors located on the top of the unit (Shown on Figure 1) will begin to operate at this time,
providing an additional safety area around the unit. If the sensors detect movement close to the Sanidyne®Premium
when less than 30 seconds remains on the countdown time, the Sanidyne®Premium will automatically reset giving 30
seconds more to leave the Operation Area. The Countdown time as well as the Treatment Time will all be displayed on the
Hand-held Remote Controller. See Figure 4, for the specic location.
Occupancy Sensors do not protect the entire Operation Area of the Sanidyne®Premium. Under no
circumstances should this sanitizer be permitted to operate with human, or animals present in the Operation Area.
4. The Hand-held Remote Controller displays the Lamp Status; When the lamp operation indicators on the display glow yellow
the lamp is on, when the lamp is off it displays grey. (See Figure 4 to locate lamp operation indicators) Once the treatment
time has expired the unit will turn off the Germicidal Ultraviolet Lamps and it is now safe to return to the area.
If at any time during the Treatment Time the Occupancy Sensors detect someone near the
Sanidyne®Premium, the xture will immediately turn off and send an alarm to the Hand-held Remote Controller and
the Sanidyne®Premium. If this event occurs the alarm can be turned off on the remote by pressing anywhere on the
display or at the Sanidyne®Premium by pressing the START/STOP on the Keypad. If the Alarm is turned off at the
Sanidyne®Premium the operator can reset the xture by pressing the START/STOP button on the keypad controller
again to begin the 1:30 countdown to allow all inhabitants to leave the area. After the 1:30 has elapsed the Sanidyne®
Premium will power on and complete the remaining Treatment Time left prior to the alarm.
If the Hand-held remote is used to stop the alarm, the operator must return to the area and ensure that the area is safe
to proceed. Select the START/STOP button on the keypad controller to begin the 1:30 countdown to allow all inhabitants
to leave the are. After the 1:30 has elapsed the Sanidyne®Premium will power on and complete the remaining
Treatment Time left prior the alarm.
setting date and time
Option 1 – Using the tablet’s Settings menu:
1. Navigate to the tablet’s settings menu by tapping the Settings icon on the Home Screen or in the App Directory.
2. Scroll down to Date & Time under System.
3. Use the Set Date, Set Time, and Select Time Zone functions to set the correct date and time.
Option 2 – If starting in the LampControl app Settings menu:
1. Press the Settings Button. (See “Hand-Held Remote Controller Overview” on pages 8–9.)
2. Press Set Date/Time.
3. Press Admin Pin. Using keyboard, enter Pin number 1234. (This will bring you to the tablet’s Settings menu.)
4. Scroll down to Date & Time under System.
5. Use the Set Date, Set Time, and Select Time Zone functions to set the correct date and time.
saving asession
Saving a Session: At the end of a Session or after a Session is Stopped the “Save This Session” box will appear.
To save a Session:
1. Press Yes under Save Session.
2. Press on Note Entry
3. Type in Session Notes, press OK
Clearing Total Operating Time or Clearing Session Data:
1. Press Settings Button
2. Press Settings
3. Press on the box next to “Reset Total Operating Time” and/or “Clear Session Data.”
4. Press Home Button.

13
determining treatment time for room sizes
The Sanidyne®Premium is intended for use in UNOCCUPIED AREAS ONLY. Under no circumstances
should this unit be permitted to operate with humans, plants or animals present in the Operation Area. Consult our UV
Application Specialists if you have any questions or need help with the Sanidyne®Premium.
1. The xture should be located in the approximate center of the room and target surfaces must be directly exposed to the
ultraviolet rays. It is important to remove items from direct line of sight that would block or shield UV rays from striking
target surfaces. Depending on the conguration of the space, and what specic disinfection you are looking to achieve, it may
be advisable to operate the Sanidyne®Premium on each side of large xed objects (like a bed, or table, etc).
2. Measure the longest distance from the Sanidyne®Premium to the farthest wall. Use this length to compare to the Distance
From Fixtures / Time (Minutes) shown on Figure 5 below.
3. For example, if the distance from your xture measures 15 feet, nd the 15 foot mark on the bar chart for each time range.
As the treatment time increase, dose increases. (NOTE: The number at the end of each bar is the expected dose for each time
increment in millijoules per square centimeter.)
4. If a greater dose is required, increase treatment time.
Figure 5 – Treatment Time and UV Dosage Based on Distance from Fixture – Sanidyne®Premium
Note: Dose shown above is expressed as mJ/cm2 (millijoule per square centimeter).
72.00
60.00
48.00
36.00
24.00
12.00
17. 2 8
2 7.0 0
48.00
108.00
34.50
54.00
96.00
216.00
51.84
81.00
144.00
324.00
69.12
108.00
192.00
432.00
86.40
135.00
240.00
540.00
103.68
162.00
288.00
648.00
5
10
15
20
Time (Minutes)
Dose (mJ/cm2)
25
30
Distance From Fixture
10.0 Foot 15.0 Foot 20.0 Foot 25.0 Foot 30.0 Foot

14
MAINTENANCE
IN ORDER TO PERFORM THIS TASK, WEAR PERSONAL PROTECTION EQUIPMENT; GLOVES,
LONG SLEEVE SHIRT WITH NO GAPS BETWEEN CUFFS AND GLOVES, AND AN ULTRAVIOLET
BLOCKING FACE SHIELD MUST BE WORN TO COVER AND PROTECT EYES AND EXPOSED SKIN.
Always disconnect power to the xture before performing any service or maintenance.
• A regular cycle of cleaning each STER-L-RAY ®Germicidal Lamp MUST be established based on visual inspection and
experience. The frequency of cleaning will vary with the conditions surrounding each installation. It is recommended that the
germicidal lamp(s) and Sanidyne®Premium surfaces be cleaned at least once every three (3) months.
• The STER-L-RAY ®Germicidal Lamp(s) used in the Sanidyne®Premium xture have a manufacturer’s rated average
effective life of 13,000 hours. STER-L-RAY ®lamps may operate longer than their rated effective life, but the reduction in
ultraviolet output will make it impractical to use past the manufacturer’s rated life. For maximum efciency lamp replacement
is recommended every 13,000 hours of operation.
• Unless lamp replacement is due to failure or breakage, it is recommended that all lamps be replaced at the same time.
• It is recommended that the user maintain a log of all maintenance performed on Sanidyne®Premium. (See Page 17.)
Personal protection equipment, such as gloves; long sleeves with no gaps between cuffs and
gloves, and an ultraviolet resistant face shield, is required when entering the irradiated space.
germiCidal lamP installation, rePlaCement, or Cleaning
IN ORDER TO PERFORM THIS TASK, WEAR PERSONAL PROTECTION EQUIPMENT; GLOVES,
LONG SLEEVE SHIRT WITH NO GAPS BETWEEN CUFFS AND GLOVES, AND AN ULTRAVIOLET
BLOCKING FACE SHIELD MUST BE WORN TO COVER AND PROTECT EYES AND EXPOSED SKIN.
NOTE: STER-L-RAY ®lamps used in the Sanidyne®Premium have ArmorLiteTM Safety Shield (which is a protective
covering over the glass of the lamp— DO NOT REMOVE this covering.)
Always disconnect power to the xture before performing any service or maintenance.
Germicidal lamps are easily damaged. Exercise care when handling lamps.
1. To remove lamps follow the steps under “Lamp Installation” on Page 9 in reverse order.
2. Moisten a clean, lint-free cloth with denatured alcohol and wipe down the outer surface of the lamp.
3. When lamp has been removed and cleaned, then safely set aside, remove any loose dust or dirt from the surface of the xture
with a soft, dry cloth or vacuum.
4. To reinstall lamps follow the steps under “Lamp Installation” on Pages 9–10.
5. Re-install the top cover and tighten hardware as shown.
6. Reconnect Sanidyne®Premium to utility power, and restart.
Avoid exposure to direct or strongly reected germicidal ultraviolet rays.
Germicidal ultraviolet rays are harmful to the eyes and skin.
lamP BreaKage
Broken Quartz is SHARP.
Wear protective gloves when handling broken ultraviolet lamps. In the event of breakage, DO NOT
use a household vacuum cleaner to pick up fragments of the lamp. Sweep up debris into a plastic
bag and dispose of in accordance with local and /or state regulations.
disPosal of merCury added lamPs
Germicidal ultraviolet lamps, like standard uorescent lamps contain small amounts of mercury. Mercury added
lamps should not be placed in the trash. Dispose of properly. For further information regarding the disposal and
recycling of lamps containing mercury, along with Federal and State requirements visit LampRecycle.org. For more
information on STER-L-RAY ®Germicidal Ultraviolet Lamps, visit Ultraviolet.com or BuyUltraviolet.com.

15
TROUBLESHOOTING
Always disconnect power to the xture before performing any service or maintenance.
IN ORDER TO PERFORM THIS TASK, WEAR PERSONAL PROTECTION EQUIPMENT; GLOVES,
LONG SLEEVE SHIRT WITH NO GAPS BETWEEN CUFFS AND GLOVES, AND AN ULTRAVIOLET
BLOCKING FACE SHIELD MUST BE WORN TO COVER AND PROTECT EYES AND EXPOSED SKIN.
IMPORTANT: This xture is to be serviced ONLY by qualied and factory authorized personnel.
Table 1 – Troubleshooting
Problem Possible Cause Corrective Action
Sanidyne®Premium
not operating
Power disconnected Check connections.
Fuse not operating Remove power connector to check and
replace fuse if necessary.
Lamp not operating
STER-L-RAY ®
Germicidal lamp faulty
Swap suspect lamp, with lamp known to be good.
If suspect lamp does not operate, replace lamp.
STER-L-RAY ®Germicidal
lamp not properly seated Check lamp socket and re-install lamp if necessary.
Loose Connection Inspect for loose or disconnected wires.
Surelite™ Ballast not operating Disconnect the xture from utility power; then replace ballast.
Sanidyne®Premium
fails to shut off
Microprocessor
assembly faulty
Wearing protective clothing and face shield, enter area, and
disconnect power to unit. Call factory for technical service.
Cooling fan
not operating Fan failure Check fan connections and replace if it does not operate.
Low air ow through
cooling fans Fan lter clogged Remove lter and clean. Replace if lter appears worn or old.
TECHNICAL SPECIFICATIONS
Table 2 – Technical Specications
Model: 40-5240C
Voltage: (v) 120v
Amperage: (A) 16A
Hertz: (Hz) 50/60 Hz.
Maximum Treatment Time: (Hours) 24 Hours
Weight: (Pounds) 76 lbs.
Dimensions:
Length: (Inches) 21-3/4″
Width: (Inches) 20-15/16″
Height: (Inches) 68-1/2″
Lamp Data:
Lamp Model: 05-0250
Number of Lamps: 8
Power Consumption:  (Watts per Lamp) 176W
Ultraviolet Output:  (Watts per Lamp) 60 UV Watts
Average Effective Life: (Hours) 13,000 Hours
 Wattage is lamp watts only and does not include ballast loss.
 Ultraviolet output at 254nm at 100 hours and 80 °F (approximate).
All specications, dimensional data, etc are approximate and subject to change without notice.

16
OPTIONAL ACCESSORIES
1. ZenithTM Germicidal Ultraviolet Detector (30-1015): A sensitive, hand-held, self-contained battery operated ultraviolet
meter that can be used for:
• Monitoring UV-C Germicidal Lamp Intensity & Aging
• Measuring UV-C Germicidal Fixture Leakage.
2. Promate™Safety Glasses (00-1299): Safety eyewear MUST be used as general-purpose safety protection and for
additional shielding from ultraviolet rays.
3. Additional Promate™Face Shields (00-0126): Lightweight visor with adjustable headgear provides eye and face
protection from ultraviolet rays. Two (2) face shields are included with purchase of Sanidyne®Premium but additional
face shields may be purchased.
4. Additional Promate™Danger Signs (98-1827): Glossy card stock signs (8-1/2″ x 11″) to be afxed to entry door(s) to
warn that an ultraviolet sanitizer is in use and that the treatment area MUST not be entered. Sanidyne®is for use only
in unoccupied areas. Four (4) warning signs are included with purchase of Sanidyne®Plus but additional signs may be
purchased. NOTE: Danger Signs have English on one side and Spanish on the other.
5. Assure™ UV-C Dosimeter (00-0376): A portable, full-featured instrument that provides highly-accurate UV-C
measurements in mJ/cm2. Sits upright, on back or side, and can be placed in supplied wall holder. Uses 1 AAA battery.
6. UV-C Dosimeter Card (00-0373): Contains a patented colorimetric indicator that changes color at 25, 50, and 100 mJ/cm2to
visibly conrm that your Sanidyne®Premium is achieving the desired UV-C exposure. Each card is designed for one (1)
treatment cycle and CANNOT be reused. Complete instructions for use are on back of card. One (1) card has been included
with this purchase but additional cards may be purchased by phone or on BuyUltraviolet.com.
7. Personal UV-C Exposure Indicators (00-0375): These indicators change color to reveal the word “STOP” if personnel are
exposed to an accumulated dose of 6 mJ/cm2of UV-C irradiation. Adhesive backing sticks to clothing. Available in packs of
10. Designed for single, daily use and CANNOT be reused.
For more information and purchasing contact our ofces, weekdays between 8:30 am and 5:00 pm Eastern time, at:
Atlantic Ultraviolet Corporation®, 375 Marcus Boulevard, Hauppauge, New York, 11788
Tel: [phone] • Fax: [phone] • Email: [e-mail] • Website: Ultraviolet.com – BuyUltraviolet.com
REPLACEMENT PARTS
Table 3 – Replacement Parts
Item No. Description Part No.
1STER-L-RAY ®Germicidal Lamp 05-0250
2Surelite™ Ballast 10-0255
3Cooling Fan Guard with Filter 40-1467
4 Line Cord : 10ft, 20A, 120v 35-2122
5Fuse: 250v 20A 35-2123
Other replacement parts are available. Consult Atlantic Ultraviolet Corporation® for specic requirements.

17
MAINTENANCE LOG
Date Maintenance Performed Service Person Comment(s)

18
MAINTENANCE LOG
Date Maintenance Performed Service Person Comment(s)

19
MAINTENANCE LOG
Date Maintenance Performed Service Person Comment(s)