Retractable Awnings KONYA User manual

SUNTECH -QUATTRO
Technical Details
All information contained in this document was provided by the
manufacturer of the components for this particular model. As a
fabricator/distributor, Retractableawnings.com Inc. claims no
liability with respect to these documents as we are not engineers
and did not complete any of the information, engineering or
calculations in this document.
All measurements in this document are metric. To convert from
metric (meters, centimeters and millimeters) to imperial (feet
and inches) visit this website:
http://www.onlineconversion.com/length_common.htm
KONYA
INSTALLATION
INSTRUCTIONS
Tel: [phone] or
[phone]
All information contained in this document was provided by the
manufacturer of the components for this particular model. As a
fabricator/distributor, Retractableawnings.com Inc. claims no
liability with respect to these documents as we are not engineers
and did not complete any of the information, engineering or
calculations in this document.
All measurements in this document are metric. To convert from
metric (meters, centimeters and millimeters) to imperial (feet
and inches) visit this website:
http://www.onlineconversion.com/length_common.htm
Page 1

DIN 933
M8 x 25
STEP I
MOTOR SIDE
Quattro
Installation
GUTTER
160
160
10
DIN 933
M8 x 25
160
17
6
90
POST
GUTTER
Page 2

STEP II
FRONT SIDE
Quattro
Installation
GUTTER
160
17
6
90
160
160
10
DIN 933
M8 x 25
DIN 933
M8 x 25
Page 3

Quattro
Installation
RAFTER SIDE GUTTER
STEP III
RAFTER SIDE GUTTER
SLICONE
DIN 7504-P
4,2x19
RAFTER SLICONE
SLICONE
DIN 7504-P
4,2x19
RAFTER
RAFTER SIDE GUTTER
Page 4

STEP IV
Quattro
Installation
RAFTER
ISO 7380-A2
M8 x 16
90,6 mm
ISO 7380-A2
M8 x 16
Page 5

ISO 7380-A2
M8 x 20
ISO 7380-A2
M8 x 20
MOTOR BOX
Quattro
Installation
MOTOR BOX
STEP V
M8x12
M8x12
SQUARE MIL ISO 7380-A2
M8 x 20
M8x12
MOTORBOX SUPPORT
PLATE
Page 6

Quattro
Installation
TOP COVER
STEP VI
TOP COVER
ISO 7380-A2
M8 x 20
ISO 7380-A2
M8 x 20
ISO 7380-A2
M8 x 20
M8x12
M8x12
M8x12
MOTORBOX SUPPORT
PLATE
Page 7

LIGHTING CHANNEL
LIGHTING CHANNEL
DIN 7504-P
4,2x19
DIN 7504-P
4,2x19
Quattro
Installation
TOP COVER
STEP VII
Page 7
Page 8

STEP VIII
Installation of fabric
FABRIC
DIN 7040
M8 PREVAILING
TORQUE NUT
DIN 7040
M8 WASHER
Quattro
Installation
PULLER BAR
(BACK)
MIDDLE SUPPORT BAR
PULLER BAR
(FRONT)
Page 8
Page 9

RAFTER TOP CAP
DIN 7504-P
4,2x19
Quattro
Installation
RAFTER TOP CAP
STEP IX
Page 10

Quattro
Installation
RAFTER SIDE COVER
DIN 7504-P
4,2x19
STEP X
Page 11

Quattro
Installation
GUTTER CAP
DIN 7504-P
4,2x19
STEP XI
Page 12

Quattro
Installation
RAFTER END CAP
STEP XII
Page 13

Quattro
Installation
Programming RTS Somfy motor
My
up dir. button
my button
down dir. button
channel leds
channel button
programming button
Front side Back side
Step1:
Connect the motorbox to 220 AC power
-Blue : Notr
-Brown:Phase
-Green-Yellow:Ground
Step3:
My
Press the up and down button
at same instance motor will
give a click.(this means motor
and remote control unit is introduced to
each other.
Step4:
My
Press the up button to check the
direction of movement.If the fabric moves to
up direction go on to step 6, if no go on to
step 5.
Step5:
Press the My button until the motorbox
gives a click.The direction is reversed
My
Step6:
Move the fabric to back limit position
that the fabric is totally gathered under
the front top cover support profile.
My
Step2:
My
Check the channel for programming
motor.Pres the channel button to select the
channel 1 , make the channel 1
led light flashing.
Step7:
Press the My buttton & Down Dir. Button
at the same instance for once the fabric
will start to move down direction.And stop
the movement with My button apprx. 5 cm
before the front en limit.
My
Step8:
Press the down dir. button will small time
intervals until the fabric is fully tensioned.
My
Step9:
My
Press the My buttton & Up Dir. Button
at the same instance for once the fabric
will start to move up direction.And will stop
itself at back limit position.
Step10:
My
Stay pressing the My buttton until the motor
will give click movement.
Step11:
Press the programming button once.
The programming is finished.
STEP XIII
Page 14

220 AC
WHITE LIGHT DIMMER BOX
output TRAFO
EXTENSION CABLE
EXTENSION CABLE
MONO
2P 4H EADS C ABLE 60CM FEMALE
CONN ECTOR (F OR WHIT E)
WHITE
LED
Page 15

220 AC
output TRAFO
EXTENSION CABLE
EXTENSION CABLE
RGB
RGB DRIVER BOX
4P 4H EADS C ABLE 60CM FEMALE
CONN ECTOR (F OR RGB )
RGB
Page 16