Super Handy GUT164 User manual

Warning: Please read and thoroughly understand all instructions before operating. Failure to follow
safety rules and other basic safety precautions may result in serious personal injury. Keep these
instructions in a safe and easily accessible place so that they can be referred to when needed. Retain
these instructions to assist in future servicing.
© SuperHandy All Rights Reserved | Version 1.0superhandyus.com
4 Wheels Folding Mobility Scooter
| GUT164 GUT165
Operator’s Manual

A mobility scooter is not a toy. It is an electrically powered scooter and failure to follow safe operating
procedures and safety warnings at all times could result in serious personal injury or death in addition to the
injury or death of others.
The symbols below are used throughout this owner’s manual and on the scooter to identify warnings and important
information. It is very important for you to read them and understand them completely.
WARNING! Indicates a potentially hazardous condition/situation. Failure to follow designated procedures can
cause either personal injury, component damage, or malfunction.
MANDATORY! These actions should be performed as specified. Failure to perform mandatory actions can
cause personal injury and/or equipment damage.
PROHIBITED! These actions are prohibited. These actions should not be performed at any time or in any
circumstances. Performing a prohibited action can cause personal injury and/or equipment damage.
CALIFORNIA PROPOSITION 65 WARNING! This product may contain substances which are known to the
state of California to cause cancer and birth defects or other reproductive harm. For more information, go to
www.P65Warnings.ca.gov.
The scooter has been designed and engineered to be very safe during normal operation. Aswith all cordless products,
certain safety precautions should be taken.
Driving a mobility scooter requires a combination of healthy traits and abilities, including but not limited to: good vision;
strength; coordination; balance and concentration. If you have these traits and abilities, you are on the right track.
UNDERSTAND THESE SAFETY PRECAUTIONS BEFORE OPERATING MACHINE. FAILURE To PROPERLY FOLLOW
THESE PRECAUTIONS MAY LEAD To A FIRE, EXPLOSION, OR ELECTRICAL SHOCK HAZARD.
INTENDED USE
The intended use of this Battery Powered Scooter is to provide mobility to persons with full use of their upper and lower
extremities and who are able to support themselves in an upright position. This product is primarily for indoor use and the
outdoor capabilities are limited to hard, flat, and even surfaces such as concrete, black top, and other similar surfaces. While
we understand that the scooter’s outdoor capabilities are limited, when driving near uneven obstacles, follow the safety
guidelines outlined within the safety section of this manual.
* Non-Medical Device
This product is not a medical device and is not intended to assist, treat, diagnose or alleviate any medical condition or
disability.
1EN
WARNING

SAFETY INTRODUCTION
1. SAFETY INSTRUCTIONS. The below instructions and tips will help you to operate your Scooter safely.
PLEASE NOTE - The Scooter is designed to be used by one person at a time and is not recommended for any person
younger than 16 years old.
• Read this Manual and all safety and training instructions and all warning labels before operating the Scooter.
• Do not carry passengers or exceed the maximum weight capacity.
• Do not mount or dismount the Scooter unless it is resting at a complete stop, on a level surface, parking brake
engaged and is turned off.
• Comply with all local laws and regulations while operating the Scooter.
• Check that all folding levers and clamps are securely locked before use.
• Always slow down before changing directions and turning.
• Always use both hands on the handlebar.
• Always keep your feet on the foot rests when driving the Scooter.
• Always approach small obstacles straight on and at slow speeds. Do not attempt to drive over curbs, potholes,
puddles or any other road hazards. Use common sense when operating the Scooter. Reckless driving can result in an
accident!
2. SAFE OPERATING CONDITIONS:
• Do not operate this scooter in traffic.
• Be very careful with inclines. Read below sections for details
• Do not operate this scooter on surfaces that are wet, frozen, oily, or unpaved.
• Never carry passengers or objects that can hinder your ability to safely operate this scooter.
• Never use headphones or a cell phone to talk or text while riding.
• Do not exceed the maximum weight capacity.
3. PREGNANT OPERATORS: Pregnant women should not operate this scooter.
4. DRIVING IMPAIRED: Never use alcohol or drugs before or while operating this scooter. The use of such hinders your
ability to safely operate the scooter.
5. STUNTS: This scooter is not designed for stunts or tricks and should not be used as such. High speeds, jumps, wheelies,
and other trick maneuvers are dangerous and can result in loss of control, accidents, and injury/death to self or others.
6. INCLINES: Never operate this scooter on steep inclines (inclines that have slopes steeper than a standard handicap
ramp). Always climb and descend inclines straight on and at slow speeds. When climbing inclines, you may need to allow
more power to the motor and maintain your speed depending on the steepness of the hill and rider weight so that the
scooter does not lose momentum.
If the scooter loses momentum and comes to a stop on an uphill, quickly apply the hand brake and put both feet on the
ground. Get off the Scooter and walk the product either up or down the incline.
The scooter has a short wheel base and a high center of gravity. It may become unsteady at excessive speeds. Avoid
excessive speeds that can be associated with downhill rides. When going downhill, always actuate the brakes to
control the speed. The scooter has a mechanical brake. Always check the brake BEFORE beginning to go downhill.
Never go downhill without brake being enabled.
Failure to control your speed or attempting a sharp turn when descending a hill can result in serious injury or death.
7. GUEST USE: Never permit a guest to use this scooter unless the guest has read the user manual and all the warnings.
Never allow more than one person at a time to ride the scooter. Never exceed the maximum weight capacity.
EN2
WARNING

This product should not be used by persons unwilling or unable to take responsibility for their own actions.
8. INSURANCE: YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE
USE OF THIS SCOOTER. TO DETERMINE IF COVERAGE IS PROVIDED, CONTACT YOUR INSURANCE COMPANY
OR AGENT BEFORE USING THE SCOOTER.
9. OPERATOR AGE: Do not allow anyone under the age of 16 to operate this scooter. This scooter is designed for operation
by and the transport of only one person age 16 or older.
10. SURROUNDINGS: Ride your scooter in a controlled environment away from vehicles, obstacles, and other hazards.
Never operate the scooter near steps or swimming pools. Do not drive the scooter on grass, gravel, or any other
textured or bumpy surface.
11. INTENDED USE: This scooter is not designed or intended for stunt tricks, including but not limited to jumps, back wheel
wheelies, front wheel wheelies, or operating while standing on the scooter. Always stay seated, keep both hands on the
handlebar, both feet on the foot pedal and all three wheels touching the ground while operating the scooter.
12. SPEED: The scooter’s maximum speed gives the scooter the most torque or power for climbing inclines. For your safety,
be careful to control your speed when descending hills or turning. The scooter has a short wheel base and can become
unsteady at excessive downhill speeds or sharp turns.
Do not use maximum speed while making turns.
13. VISIBILITY: Do not ride your scooter at night or in conditions of poor visibility.
Riding at dawn, dusk, or at times of poor visibility without a lighting system that meets state and local laws, and without
approved reflectors, is illegal, dangerous, and can result in serious injury or death.
14. TEMPERATURE: Do not use the scooter when the temperature is below 0ºC (32ºF).
15. WEATHER CONDITIONS: Avoid riding in wet or icy conditions. Stop the scooter and walk it across rough or slippery
road conditions.
Wet or icy weather impairs traction, braking, and visibility for riders and other vehicles and pedestrians sharing the
roads. The risk of accident is dramatically increased in wet or icy conditions.
16. SURFACE CONDITIONS: The scooter is intended for use on hard, flat, dry paved surfaces without loose debris such as
sand, leaves, rocks. Wet, slick, bumps, uneven or rough surfaces may impair traction and contribute to possible
accidents. Do not ride your scooter in mud, sand, ice, or water. Watch out for potential obstacles that could catch your
wheel or force you to swerve suddenly or lose control. Avoid sharp bumps, drainage grates and sudden surface
changes. Stop the scooter and carefully walk it across rough or slippery road conditions.
17. WATER RESISTANCE: Although some water resistance measures have been made, riding the scooter through
standing water, rain, wet or muddy conditions runs the risk of severely damaging it. Do not immerse the scooter in water
or directly spray the scooter when cleaning. When parked outside where rain is possible, cover the handlebar controls
with water resistant materials to protect the electric controls.
3EN
WARNING
WARNING
WARNING
WARNING

18. SAFETY WHEN NOT RIDING: When the scooter is not being used for riding, place it in a safe stable and secured
environment, keep it away from fire, water and other hazards. When the scooter is in its upright vertical self standing
mode, especially in moving public transportation or other crowded space, pay attention to its stability as accidental
tipping-over could cause personal injury as well as damage to the scooter. Always hold the handlebar to prevent it from
tipping over and falling to the ground. To save the battery life, SWITCH OFF the power, or REMOVE the battery from
scooter, when reset.
TECHNICAL DETAILS
* Top speed and range per charge depends on rider weight, wind speed, temperature, riding style,
riding surface, battery condition, and other factors. Actual top speed and range per charge may
vary.
* NEVER exceed the maximum total weight limit of 330Lbs (150Kgs).
EN4
Performance
Size & Weight
Tires
Motor
Detachable Battery
Charger
Load capacity
Forward speed
Revise speed
Range per charge
Unfolded dimension
Folded dimension
Handlebar-to-Ground height range
Seat-to-Ground height range
Frame weight
Detachable battery weight
Seat weight
Product weight
Seat size
Ground clearance
Size
Brake
Brake distance
Input voltage
Type
Voltage
Capacity
Type
Continue working time per charge
Input voltage
Charging time
330Lbs (150Kgs)
Up to 3.7mph* (6km/h)
1.5mph (2.4km/h)
Up to 6.5miles* (10km)
41.7”×23.6”×38.2” (1060x600x970mm)
40"×23.6"×12.2” (1020×600×310mm)
23.6”~34.3” (600~870mm)
21.3”~23.6” (540~600mm)
37Lbs (16.7Kgs)
2.0Lbs (0.9Kgs)
8.2Lbs (3.7Kgs)
47Lbs (21.3Kgs)
17” x 15” (430x380mm）
2.5” (65mm) at midframe
6.75” solid
Drum brake, manual
<39” (1.0m)
48V DC
Brushless hub motor
48V DC
2.0Ah
Li-ion battery
Up to 1h20min
100-240V
1h30min

CONTROLS AND FEATURES
ASSEMBLY
1. Out of Package
Take out the Scooter frame kit, Seat stand, Seat, Front wheels, Fenders, nuts, bolts and washers from the package (Fig.01).
Other components are assembled in scooter frame kit.
5EN
Fig. 01
Scooter frame kit
Seat
Front
wheels x2
Seat standFender x2
M5
screws x2
M8
bolts x4
M10
washer x4
M10
nuts x2
10 Pedal
8
Folding lever
11 Main frame kit
12 Seat post
15 Seat
14 Battery
box
13 Rear
wheel
9Front wheel
4
Handle-bar
5
Post clamp
6
Middle bar
7
Fender
3
Brake handle
1
Accelerator 2
Switch

2. Assemble the front wheels
1) Put the one flat washer at inner.
2) Insert wheel into shaft.
3) Tighten the wheel by flat washer and nut. Completely tighten the nut.
4) Do the same at another side.
3. Unfold the Scooter
Failure to securely lock the handle bar onto the scooter frame may result in serious injury or death.
1) Push down the handle-bar a little, and lift the folding lever to release. (Fig.03)
2) Lift the handle-bar to upright, push it forward until you hear a click, which means the folding lever is locked in securely.
4. Folding the Scooter
DO NOT push the folding lever while in normal using. ONLY push it
while you want to fold the scooter. Accidently push the folding lever
when driving, may result in serious injury or scooter damage.
1) Make sure the scooter is off.
2) While pushing the handle-bar forward a little, push the folding
lever forward and it should unlock.
3) Fold down the handle-bar till you hear a “click”, which means it
should lock into the folding position
EN6
Wheel
shaft
Washer Front
wheel
Washer Nut
Fig. 02
Fig. 04
Fig. 03
Folding lever
Handle bar

7.Attach the Seat
1) Insert the seat to the scooter frame. Align the holes of seat
stand and frame (Fig.07).
2) Close level of post clamp. If necessary, you can adjust the
screw of post clamp to tighten more securely (Fig.08).
SEAT HEIGHT ADJUSTMENT
The seat can be repositioned to different heights.
1. Loosen the seat post clamp.
2. Remove seat and its attached seat post by twisting seat
left/right, and remove from seat frame.
3. Remove clevis pin from the seat post.
4. Raise or lower the seat and its attached seat post to the
desired seat height.
5. While holding the seat at the desired height, align the
adjustment holes of the seat post with notch of seat
frame.
6. Fully insert clevis pin.
7. Tighten the seat post clamp.
Screw of
adjusting tighten
Post clamp lever
Fig. 08
5. Assemble the fender
1) Left or right fender are same. Don’t worry about mixing
both.
2) Insert the fender to the assembly hook above the front
wheel.
3) Press harder to inset the position to lock it (Fig.05).
4) Assemble the screw at the side of fender. Securely screw
it.
6. Assemble the Seat Stand
Failure to properly tighten the bolts holding the seat stand
onto the seat may result in poor riding performance, the
bolts falling off may cause serious injury or death.
Be sure the bolts are securely attached to the seat before
using the scooter.
1) Turn the seat bottom side up.
2) Put the seat stand on the seat. You can decide the
position of battery housing which face left or right.
3) Tighten the bolts to fix the seat stand (Fig.06).
7EN
Fig. 05
Fig. 07
Bolts
Seat stand
Seat
Fig. 06
WARNING

Forward/Reverse (See Fig. 11)
Control knob also in left hand side. Push upward, scooter
driving direction is forward. Push downward, driving
direction is reverse.
It is normal that you engage the scooter after one second
when switch between forward/reverse. This one second is
the protection of electrical system.
Brake Handle (See Fig. 12)
●The left brake handle is controlled mechanical brake
which lock the disc brake at the rear wheels.
●When actuated brake handle, it will stop scooter and cut
power supply to the motor. Release the brake handle and
press the throttle button, power will connect motor again.
●There is parking brake at front of handle. Firstly, actuate
the brake handle. Secondly, press the parking brake. The
rear wheels are locked, and scooter is at parking situation.
Accelerator (See Fig. 13)
The right thumb control is the accelerator. The further you
pressthe accelerator down, the more energy you will
release to themotor, the speed will be faster.
CAUTION – Do not make turns at high speeds or on steep
inclines. Your scooter may tip over.
BATTERY ASSEMBLY
1) Open the battery cover, and insert the battery till you hear
a “click”, which means battery is locked in housing.
2) Holding the battery body without press the release
button at battery, and trying to remove out battery. If not,
the battery is assembled well (Fig.9).
HANDLE-BAR HEIGHT ADJUSTMENT
The handle-bar can be repositioned to different heights.
1) Loosen the lever of seat post clamp at the middle bar.
2) Move up/down handle-bar to a desired height.
3) Tighten the lever of seat post clamp.
4) If necessary, you can adjust the screw at clamp, to get a
more tighten or loosen clamping.
BASKET INSTALLATION
Your scooter has an optional basket. To install the basket,
hooks across the handle-bar, and hold in middle of
handle-bar. Then carefully rotate the hooks and rest the
hooks on the handle-bar naturally. And close the Velcro
band around the handle bar tube.
OVERVIEW THE SCOOTER
Power On/Off (See Fig. 10)
The red knob in left hand side is the power switch.
Push on it, power is On. Push on again, power is off.
EN8
Fig. 09
Fig. 10
Fig. 11
Fig. 12
Fig. 13

Battery LED display (See Fig. 14)
LED display on handle-bar can show battery capacity easily.
Push the button, 3 LEDs will show the left capacity of battery.
3 LEDs on, capacity is 100%-70%; 2 LEDs on, capacity is
70%-30%; 1 LED on, capacity is less than 30%, it’s better to
charge battery if necessary.
Battery cover (See Fig. 15)
The battery cover prevent battery from impact.
As the magnet slide at edge, it can close with housing.
Drum brake (See Fig. 16)
The brake is controlled by brake handle. While actuated brake handle,
the right rear wheel is not braked completely, you can adjust the screw
to tighten. Or if brake handle is hard to actuate, loose the screw a little.
OPERATION
●Just like learning to drive a car or ride a bicycle, operating any personal transportation device inherently includes risk and
takes practice.
●Therefore, use caution as you practice operating the scooter in various situations.
●Start driving with the lowest speed until you’re comfortable controlling the scooter.
● The below instructions and practice steps will teach you to maneuver through doorways, on and off lifts, and up and down
ramps.
● When preparing for your first ride, select an area that is flat, spacious, and away from traffic and other obstacles.
●Bring a friend along to help you follow the instructions while you practice.
●Please refer to the Overview section of this Manual for components’ instruction.
PRE-RIDE SAFETY CHECK
Get to know the feel of your scooter and its capabilities. We recommend that you perform a
safety check before each use to make sure your scooter operates smoothly and safely.
Perform the following inspections prior to using your scooter:
●Check the condition of the tires. Make sure they are not damaged or excessively worn.
●Check the folding clasp. Make sure it’s locked properly.
●Check all electrical connections. Make sure they are tight and not corroded.
●Check handle-bar and seat connections. Make sure they are secured properly.
●Check the brakes to ensure they operate properly.
●Check the battery LED display to ensure the battery is fully charged.
●Ensure the parking brake is engaged before sitting on the scooter.
9EN
Fig. 14
Fig. 15
Fig. 16