Supermicro C9X299-PGF-L User manual

C9X299-PGF-L
C9X299-RPGF-L
Revision 1.00

C9X299-PGF-L/C9X299-RPGF-L QUICK REFERENCE GUIDE Product Safety Information
Standardized Warning Statements
Motherboards
About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user of situations which can potentially
cause a bodily injury. Should you have questions or experience di󰀩culty, contact Supermicro's Technical Support De-
partment for assistance. Only certied technicians should attempt to install or congure components.
Read this section in its entirety before installing or conguring components in the Supermicro chassis.
Battery Handling
Warning!
There is a danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or an equiva-
lent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメーカーが推奨する型、または同等のもの
を使用下さい。 使用済電池は製造元の指示に従って処分して下さい。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電池。請按照製造商的說明指示處理
廢棄舊電池。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有电池。请按制造商的说明处理
废旧电池。
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사에서 권장하는 동등한
종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Note: For complete product safety information, refer to http://www.supermicro.com/about/policies/safety_information.cfm.




WARNING: This product can expose you to chemicals including
lead, known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information, go
to www.P65Warnings.ca.gov.
!

C9X299-PGF-L/C9X299-RPGF-L QUICK REFERENCE GUIDE 限用物質含有情況標示聲明書
限
限
用
用
物
物
質
質
含
含
有
有
情
情
況
況
標
標
示
示
聲
聲
明
明
書
書
設備名稱：主機板 /
Motherboard
型號（型式）：C9X299-PGF-L, C9X299-RPGF-L
單元Ｕnit
限用物質及其化學符號
鉛Lead
(Pb) 汞Mercury (Hg) 鎘Cadmium (Cd)
六價鉻
Hexavalent
chromium
(Cr+6)
多溴聯苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
主機板
(Motherboard)
－○○○○○
備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準
值。
備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
備考3.〝－〞係指該項限用物質為排除項目。
Equipment name
Type designation (Type)
Restricted substances and its chemical symbols
Declaration of the Presence Condition of the Restricted Substances Marking
Note 1：“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the
reference percentage value of presence condition.
Note 2：“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3：The “−” indicates that the restricted substance corresponds to the exemption.

C9X299-PGF-L/C9X299-RPGF-L QUICK REFERENCE GUIDE AMI BIOS POST Codes
AMI BIOS POST Codes
About AMI BIOS POST Codes
The table below lists some of AMI BIOS POST codes for C9X299-PGF-L/C9X299-RPGF-L. For more information,
refer to https://www.supermicro.com.tw/manuals/other/AMI_AptioV_BIOS_POST_Codes_for_SM_Motherboards.pdf.
Code Description
0x32 CPU post-memory initialization is started
0x55 No Memory detected or memory failed
0x63 CPU DXE initialization is started
0x69 North Bridge DXE initialization is started
0x70 South Bridge DXE initialization is started
0x92 PCI Bus initialization is started
0x99 Super IO Initialization
0x9A USB initialization is started
0xA0 IDE initialization is started
0xA9 Boot into BIOS setup menu
0xAE Legacy Boot event
0xB2 Legacy Option ROM Initialization
0xB4 USB hot plug
0xD6 No console output devices are found
0xD7 No console input devices are found
0xF2 Recovery process started
0xF9 Recovery capsule is not found

C9X299-PGF-L/C9X299-RPGF-L QUICK REFERENCE GUIDE M.2 Device Installation/Removal Instructions
M.2 Device Installation and Removal Instructions
M.2 Device Installation M.2 Device Removal

C9X299-PGF-L/C9X299-RPGF-L
QuiCk ReFeRenCe Guide Rev. 1.00
SUPERMICR R
BIOS
LICENSE
MAC CODE
IPMI CODE
BAR CODE
C9X299-PGF-L REV:1.01
+
1
+
PCI-E M.2-M2
PCI-E M.2-M1
CLEAR CMOS
U.2-1 U.2-2
I-SATA5
I-SATA4
I-SATA3
USB 4/5(3.0)
USB 2/3
USB 0/1
PCH SLOT2 PCI-E 3.0 X1
USB 10/11(3.0)
CPU SLOT1 PCI-E 3.0 X8 (IN X16)
CPU SLOT7 PCI-E 3.0 X16
CPU SLOT3 PCI-E 3.0 X8 (IN X16)
CPU SLOT5 PCI-E 3.0 X8 (IN X16)
I-SATA2 I-SATA0
I-SATA1
DIMMA1
DIMMB2
DIMMB1
DIMMA2
HD AUDIO
USB 8/9 (3.1)
LAN1 USB 6/7(3.1)
DIMMD2
DIMMD1
DIMMC2
DIMMC1
KB/Mouse
CLOSE 1st
OPEN 1st
JF1
LGA2066
VGA
LED1
JRK1
SP1
JTPM1
JPI2C1
JL1
JPAC1
JWD1
JPG1
JPME2
CPU_FAN1
CPU_FAN2
SYS_FAN2SYS_FAN3
SYS_FAN1
JBT1
JSD1
JLED1
JIPMB1
JSTBY1
MH15
MH12
MH14
JD1
J3701
LED6903
LED6904
LED7201
B2
JPW1
JPW2
JCOM1
PCH
RESET
POWER
JPB1
JPW3
BMC
Motherboard Layout and Features
=mounting hole
LGA 2066
I/O BACK PANEL

Package contents
• One Supermicro Motherboard
• Two SATA Cables
• One Quick Reference Guide
• One I/O Shield
• One Driver CD
Connector Description
B2 Onboard Battery
CPU_FAN1, CPU_FAN2,
SYS_FAN1, SYS_FAN2, SYS_FAN3 CPU/System Fan Headers
HD AUDIO High Denition Audio Ports (back panel)
I-SATA0 - I-SATA5 (Intel X299) Serial ATA (SATA 3.0) Ports (6Gb/sec)
J3701 Front Panel Audio Header
JCOM1 COM Header
JD1 Speaker/Buzzer (Pins 1~4: external speaker, Pins 3~4: buzzer)
JF1 Front Control Panel Header
JIPMB1 4-pin External I2C Header (for an IPMI card)
JL1 Chassis Intrusion Header
JLED1 LED Connector for PCH Heatsink
JPI2C1 Power Supply SMBus I2C Header
JPW1 24-pin ATX Main Power Connector (Required)
JPW2 +12V 8-pin CPU Power Connector (Required)
JPW3 +12V 4-pin CPU Power Connector (Optional)
JRK1 Intel RAID Key Header
JSD1 SATA DOM (Disk On Module) Power Connector
JSTBY1 Standby Power Header
JTPM1 Trusted Platform Module (TPM)/Port 80 Header
LAN1 1Gb LAN Port (Shared IPMI Port)
PCI-E M.2-M1, PCI-E M.2-M2 PCIe M.2 Connectors (small form factor devices and other portable devices for high speed
NVMe SSDs)
SP1 Internal Buzzer/Speaker
U.2-1, U.2-2 U.2 Connectors (for 2.5” SSD Drives)
USB 0/1, 2/3 Front Access USB 2.0 Headers
USB 4/5 Back Panel USB 3.0 Ports
USB 6/7, 8/9 Back Panel USB 3.1 Ports (USB8: Type-A, USB9: Type-C)
USB 10/11 Front Access USB 3.0 Header
VGA VGA Port (back panel)
Jumpers and Connectors
Jumpers
Jumper Description Default
CLEAR CMOS Clear CMOS Switch Push Button Switch
JBT1 Clear CMOS (onboard) Short Pads to Clear CMOS
JPAC1 Audio Enable Pins 1-2 (Enabled)
JPB1 IPMI Function Pins 1-2 (Enabled)
JPG1 VGA Enable/Disable Pins 1-2 (Enabled)
JPME2 Intel Manufacturing Mode Pins 1-2 (Normal)
JWD1 Watch Dog Function Enable Pins 1-2 (Reset)
POWER BUTTON Internal Power Button Push Button Switch
RESET BUTTON Onboard System Reset Button Push Button Switch
Connectors

ContaCt InformatIon
• www.supermicro.com (Email: [email protected])
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: https://www.supermicro.com/wdl/driver/
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
This motherboard supports a single Intel®CoreTM X-Series Processors Family on the LGA 2066 socket, up to 256GB of Unbuffered (UDIMM)
non-ECC DDR4 memory with speeds of up to 2666MHz (2DPC) ~ 2933MHz (1DPC) in eight 288-pin memory slots. Populating these DIMM
slots with a pair of memory modules of the same type and size will result in interleaved memory, which will improve memory performance.
Notes: 1) For memory optimization, use only DIMM modules that have been validated by Supermicro. For the latest memory updates, please
refer to our website at http://www.supermicro.com/products/motherboard.
2) Always connect the power cord last, and always remove it before adding, removing, or changing any hardware components.
3) 2933MHz is supported by Intel Core i9 10980XE/10940X/10920X/10900X series processors only.
4) Memory overclocking support depends on the capability of CPU and memory.
LED Indicators
LED Description Color/State Status
LED1 Status Code LED Digital Readout See User's Manual
LED7201 Onboard Standby Power LED Green: Solid on Power on
LED6903 M.2 Connector (PCI-E M.2-M2) SSD Active LED Green: Solid on M.2 Device Active
LED6904 M.2 Connector (PCI-E M.2-M1) SSD Active LED Green: Solid on M.2 Device Active
LED Indicators
CPU & Memory Support
CPU & Memory Support
Towards the CPU
DIMM Memory Installation
Towards the CPU
Memory Population Guidelines
When installing memory modules, the DIMM slots should be populated in the following order: DIMMA1, DIMMB1, DIMMC1, DIMMD1, then
DIMMA2, DIMMB2, DIMMC2, DIMMD2.
• To optimize memory performance, please use (DDR4) memory of the same type, size, and speed.
• Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed of slowest DIMM.
Recommended Population (Balanced)
DIMMA1 DIMMB1 DIMMC1 DIMMD1 DIMMA2 DIMMB2 DIMMC2 DIMMD2 CPU Support/
DIMM Channel
Total
System
Memory
4, 8, 16,
32GB
4, 8, 16,
32GB N/A N/A N/A N/A N/A N/A Core i9 7900X/9900X/10900X Series, Dual channel Up to 64GB
4, 8, 16,
32GB
4, 8, 16,
32GB
4, 8, 16,
32GB
4, 8, 16,
32GB N/A N/A N/A N/A Core i9 7900X/9900X/10900X Series, Dual channel Up to 128GB
4, 8, 16,
32GB
4, 8, 16,
32GB
4, 8, 16,
32GB
4, 8, 16,
32GB
4, 8, 16,
32GB
4, 8, 16,
32GB
4, 8, 16,
32GB
4, 8, 16,
32GB
Core i9 7900X/9900X/10900X Series,
Quad channel Up to 256GB
* Please note that 32GB is supported by Core i9 10980XE/10940X/10920X/10900X series processors only.
DIMMB1 (Gray Slot)
DIMMA1 (Gray Slot)
DIMMA2 (Black Slot)
DIMMB2 (Black Slot)
DIMMD1 (Gray Slot)
DIMMC1 (Gray Slot)
DIMMC2 (Black Slot)
DIMMD2 (Black Slot)

MNL-2424-QRG-100
© 2021 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
Notes
• Graphics shown in this quick reference guide are for illustration only. Your components may or
may not look exactly the same as drawings shown in this document.
• Refer to Chapter 2 in the User's Manual for detailed information on jumpers, connectors, LED
indicators, memory support and CPU/motherboard installation instructions.
Power Button
1
Reset Button
2
HDD LED
Power LED
Ground
Ground
19 20
NIC1 LED
X
X
NMI Ground
OH/Fan Fail LED
Vcc
X
Power Fail LED
Vcc
Vcc
Vcc
Vcc
Vcc
Front Control Panel (JF1)
CPU Installation Heatsink Installation
Back Panel I/O Connectors
1. PS/2 Keyboard/Mouse Port 5. USB6: USB 3.1 Port 9. USB9: USB 3.1 Port
(Type-C)
13. Line In
2. USB4: USB 3.0 Port 6. USB7: USB 3.1 Port 10. Center/LFE Out 14. Line Out
3. USB5: USB 3.0 Port 7. LAN1: 1Gb LAN Port (Shared IPMI Port) 11. Surround Out 15. Mic In
4. VGA Port 8. USB8: USB 3.1 Port (Type-A) 12. S/PDIF Out
Align Socket Keys
OPEN 1st
OPEN 1st
Screw #3
Screw #2
Screw #1
Screw #4
C9X299-PGF-L
1
2
3
4
5
6
7
8
9
10
12
11
13
14
15

Revision 1.00