Supermicro Supero C7H61 User manual

SUPERMICR R
CONTACT INFORMATION
MNL-1455-QRG RE V .1.0A
•www.supermicro.com (Email: [e-mail])
•Manuals: http://www.supermicro.com/support/manuals
•Drivers & Utilities: ftp://ftp.supermicro.com
•Safety: http://www.supermicro.com/about/policies/safety_information.cfm
© 2012 Supermicro Computer Inc. All rights reserved.Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written
consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
PACKAGE CONTENTS
(Applies to individual-pack only)
C7H61 (-L)MOTHERBOARD
QUICK REFEREN CE GUIDE RE V . 1.0A
•One (1) Supermicro Motherboard
•Six (6) SATA Cables
•One (1) I/O Shield
•One (1) Quick Reference Guide
MNL-1455-QRG
A. KB/Mouse Port H. LAN1 Port N. Center/LFE Out
B. USB 0 (2.0) I. USB 2 (2.0) O. Surround Out
C. USB 1 (2.0) J. USB 3 (2.0) P. S/PDIF Out (Optical)
D. COM 1 (C7H61 Only) K. LAN2 Port Q. Line In
E. VGA Port L. USB 4 (2.0) R. Line Out
F. VESA DisplayPort M. USB 5 (2.0) S. Microphone In
G. HDMI Port
JPW2
JPW1
JWOL1
13
10
9
1
DIMM1
DIMM3
JF1
1
2
15
TestedtoComply
WithFCC Standards
FORHOME OR OFFICE USE
DESIGNED IN USA
2
J14
17
10
J13
1
2
JUSB30
19
11 10
MH10
1
JD1
+
SP1
JSD1
1
JTPM1
2
1
20
19
I-SATA0
1
I-SATA1
I-SATA2
I-SATA3
A-SATA0
A-SATA1
JITP1
60
2
59
1
B1
+
128
12
J34
COM2
1
5
6
9
COM5
1
5
COM6
1
5
6
9
COM7
1
5
6
9
COM8
1
5
6
9
1
5
6
COM3
9
1
5
6
COM4
9
BIOSLICENSE
1
JWOR1 JP2 JP1
JSPDIF_OUT
JSPDIF_IN
JI2C3
JL1 JI2C4 JBT1 JP3
1
JPME2
JI2C1
1
1
JI2C2
JUSBLAN1
JUSBLAN2
A
LED1
C
LED2
C
A
R474
JPUSB1
1
JWD1
1
JPAC1
JLED1
1
1
JCPUVRD_SMB
FAN4 FAN1
1
FAN3
4
4 1
FAN2
MH6 MH7
JAUDIO1
103 128
64
39
38
2-3:Disable(Default)
1-2:Enable
JPUSB1:USBWAKEUP
2-3:Disable
1-2:RST(Default)
JWD1:WatchDog
OFF:NORMAL
ON:MEMANUFACTURINGMODE
JPME2
VCC
GND
SW
RST
SW
PWR
GND
PWR
LED-
LED-
HDD
LED+
HDD
LED+
PWR
PRINTER
SLOT6 PCI-E 2.0/3.0 X16
SLOT5 PCI 33MHz
SLOT4 PCI 33MHz
SLOT3 PCI 33MHz
OFF:DISABLE ON:ENABLE JI2C3/JI2C4:I2CBUS FOR PCI SLOT
AUDIOAC97 AND HD AUDIOJUMPER
USB10/11
USB8/9
USB3.0-0/1
JLED1:
JL1:
3PINPOWER LED
CHASSIS
AUDIOFP
SLOT1 PCI 33MHz
BUZZER
SLOT2 PCI 33MHz
JBT1
JTPM1:TPM/PORT80
CMOSCLEAR
ON:CLEAR
OFF:NORMAL
JWOR:WAKEON RING
JD1:
SPEAKER:1-4
BUZZER:3-4
JPAC1:ONBOARDAUDIOENABLE/DISABLE
1-2:ENABLE
2-3:DISABLE
ON:AC'97 JHD_AC1:
OFF:HDAUDIO
SATADOM PWR
SLOT7 PCI-E 2.0 X1
UNBNON-ECC DDR3 DIMM REQUIRED
HDAUDIO
JWOL:WAKEON LAN
DIMMA1 DIMMB1
JI2C1/JI2C2:I2CBUS FOR PCI-E SLOT
OFF:DISABLE
ON:ENABLE
RST
ON
PWR
LAN2/
USB4/5
LED
OH/FF
XLED
HDD
NIC1
NIC2 LED
PWR
USB2/3
LAN1/
HDMI/DP
VGA/COM1
/CPUFAN
INTRUSION
KB/MOUSE& USB0/1
Jumpers, Connectors and LED Indicators
Back Panel I/O Connectors
Memory Support
Motherboard Layout and Features
CPU Installation
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide.
Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,
and LED indicators.
Heatsink Installation Front Panel Control (JF1)
Screw #1 Screw #2
Motherboard
Screw #3
Mounting Hole
Heatsink Bracket
Power Button
OH/Fan Fail LED
1
NIC1 LED
Reset Button
2
HDD LED
Power LED LED_Anode+
LED_Anode+
LED_Anode+
Ground
Ground
NIC2 LED LED_Anode+
XX
LED_Anode+
Jumpers
Connectors
LED Indicators
The C7H61 motherboard series supports up to 16GB of Unbuffered (UDIMM) non-
ECC DDR3 1600/1333/1066 MHz in 2 memory slots.
Note: For memory optimization, use only DIMM modules that have been validated by Supermicro.
For the latest memory updates, please refer to our website a at http://www.supermicro.com/
products/motherboard.
Memory Population Guidelines
When installing memory modules, the DIMM slots should be populated in the following
order: DIMMA1 and DIMMB1.
•Always use DDR3 DIMM modules of the same size, type and speed.
•Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed
of the slowest DIMM.
•The motherboard will support one DIMM module.However for best memory
performance, install DIMM modules in pairs.
Recommended Population (Balanced)
DIMMA1 Slot DIMMB1 Slot Total System Memory
2GB 2GB
2GB 2GB 4GB
4GB 4GB
4GB 4GB 8GB
8GB 8GB
8GB 8GB 16GB
Note: Due to memory allocation to system devices, the amount of memory
that remains available for operational use will be reduced when 4 GB of RAM
is used.
DIMMB1
DIMMA1
Towards the edge of the motherboard
Towards the CPU
DIMM Memory Installation
5 JPAC1 Audio Enable Pins 1-2 (Enabled)
8,10JI2C3,JI2C4 SMB Header for PCI Slots C7H61-L: Short (Enabled), C7H61: Open (Disabled)
12 JBT1 CMOS ResetOpen (Disabled)
13 JPUSB1USB Wake-Up Pins 2-3 (Disabled)
32 JWD1 Watch Dog Timer Reset Pins 1-2 (Reset)
41,42JI2C2,JI2C1 SMB Header for PCIE SlotsOpen (Disabled)
43 JPME2 Intel ME Manufacturing Mode Pins 1-2 (Disabled)
30 LED1 Onboard Standby PWR LED Green: Solid on Standby Power is On
1 Backpanel I/O See "Backpanel I/O Connectors", below
2AUDIO FP Front Panel Audio Header
3 JWOL Legacy Wake-On-LAN Header
4,14 COM2, COM3~8 COM2 Header, COM3~8 (Not supported on C7H61-L) )
6,7 S/PDIF OUT, S/PDIF IN S/PDIF OUT/IN Digital Audio Headers
9JL1 Chassis Intrusion Header
11 JWOR Wake-On-Ring Header
15 USB 3.0 1/0USB Header 1/0 (3.0) (Not supported on C7H61-L)
16,45USB10/11,8/9USB 2.0 Header 10/11,8/9
17,20A-SATA 0,1 (ASMedia) SATA 3.0 Ports (up to 6Gb/s)
18 JTPM1 Trusted Platform Module (TPM) Header
19 JSD1 Disk-On-Module (DOM) Power Header
24,22,23,21 I-SATA 0,1,2,3 (Intel) SATA 2.0 Ports
25 B1 System Battery
26,28,37,39 FAN 3,2,1,4 System FAN Headers 3,2,1 (CPU FAN),4
27 U5 BIOS Chip
29,40 JPW1,JPW224-Pin, 4-Pin Aux Power Supply Connectors
31 JF1 Front Panel Control Header
33 JLED1 3-Pin Power LED Header
34 Test Header Reserved for OEM
35 JD1 External Speaker Header (Pins 2-3 shorted for internal buzzer)
36 SP1Internal Buzzer
38 CPU Socket H2 for an LGA 1155 CPU
44 PRINTER LPT1 Header
1
2
DIMMA1
3
4
Audio
56
7
9
8
12
11
10
13
14
16
15 17 18 19
20
21
23
22
24
25
26 27
28 29 31
30
32 33
36
35
34
37
38
39
40
41
42
43
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
DIMMB1
SLOT4
SLOT5
SLOT6
SLOT7
SLOT3
SLOT2
SLOT1
= mounting hole
44
45