Supermicro P3TDE6 User manual

Motherboard Components
Front Panel Functions
1. 6 SCA Ultra160 Hot-swap drive bays
2. 1 Slim CD-ROM
3. Floopy Drive
4. 1 x 5.25" drive bay
5. Overheat: Indicates an overheat condition in the system
6. NIC1: Indicates network activity on LAN1 when flashing
7. HDD: Indicates IDE channel activity.
8. Power: Indicates power is being supplied to the system's
power supply units
Note: E.C.C. registered memory type must be installed in pair.
*
Rear Panel Functions
1 System Board
2 Adaptec AIC-7899
3JA6
4 JA2
5 JA4
6 SLED1
7Ultra160 LVD SCSI CHA
8 Ultra160 LVD SCSI CHB
9ServerWorks Chipset
10 JP60
11 JP63
12 WOR
13 WOL
14 JBT1
15 JP64: Watch Dog
16 Battery
17 Super I/O
18 JP57: BIOS1, BIOS2
19 Chassis Fan
20 IDE#1, IDE#2
21 Floppy Connector
22 Ultra SCSI (Channel B)
23 JF1
24 JF2
25 Chassis Fan
26 JP62
27 JP52: Chassis Intrusion
28 ATX Power #2
29 JP56
30 JP55
31 Bank 0
32 Bank 1
33 ATX Power#1
34 North Bridge
35 JP65
36 JP1, JP3
37,38 CPU#2, CPU#1
39 ATX PWR Conn.
40,41 CPU1 Fan, CPU2 Fan
42 Mouse and Keyboard Connectors
43 2 USB
44 COM 1, COM 2
45 Printer Port
46 LAN
47 AGP Pro
48,49 2 64-bit PCI (66MHz)
50,51,52,53 4 64-bit PCI (33MHz)
54 JP58
1. AC Power connector
2. PS/2 Mouse and Keyboard port
3. 2 USB ports
4. COM 1
5. COM 2
6. 1 Parallel port
7. 1 Intel 82559 LAN port
8. 7 Low-Profile 64/32-bit Expansion slot
36
29
47
12
5
42
26
1
17
15
14
13 40
10
7
6
8
9
24
22
20 39
37
19
21
48 44
43
46
45
41
42
23
25
38
18
30
11 16
49
51
50
35
31
34
32
33
3
52
54
2
345
6
7
8
5678
1
2
4
3
1
27 28
53

P3TDE6 Quick Reference
CPU Core/Bus Ratio Selection
(DIP Switch 1)
To protect the system and components, it is essential that you reinstall the top panel after you have finished working on the system.
Due to the fact that adequate air flow and proper
thermal control are very critical in maintaining 2U
system's stability and performance, it is
imperative that the proper installation procedures
listed below be followed in order to maximize
system performance.This is especially critical for
2U Dual Processor Servers with speeds of 1 GHz
and above.
Warning !
CPU Heat Sink Installation Procedures
(For Supermicro SuperServer 2U Systems)
Cooling Fan Installation
CPU
400/533
450/600
500/666
550/733
600/800
650/866
700/933
750/1000
800/1064
850/1130
950/1260
1000/1330
1050/1400
SW1 #1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
SW1 #2
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
OFF
OFF
SW1 #3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
SW1 #4
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
Jumper Description Default Setting
JA2  LVD SCSI Ch A Term Open (Enabled)
JA4 LVD SCSI Ch B Term Open (Enabled)
JA6  50-pin SCSI Ch B Term Open (Enabled)
JBT1  CMOS Clear Pin 1-2 (Normal)
JP1  FSB Speed Setting Pin 1-2 (Auto)
JP3 Spread Spectrum Enable Open (Disabled)
JP55 Third P/S Fail Enable/Disable Open (Disabled)
JP56  Speaker Enable/Disable On (Enabled)
JP57 BIOS Select Pin 1-2 (BIOS1)
JP58 LAN/NIC Enable/Disable Open (Enabled)
JP60 SCSI Enable/Disable Pin 1-2 (Enabled)
JP62  Chassis/Over Heat Fan Select Close
JP64 Watch Dog Open (Disabled)
JP65 CPU Fan Tachometer Open
1) Only those CPU heat sinks that are provided by Supermicro should be used.
2) Apply a small amount of silicon compound on the CPU's die.
3) Place the CPU heat sink on top of the CPU.
4) Place the heat sink spring on top of the CPU heat sink and secure the clip of the spring into its notch.
(Make sure the clip position is the same as the picture shown above.)