Supermicro Supero X9SRi-3F User manual

SUPERMICR R
ContaCt InformatIon
• www.supermicro.com(Email:[email protected])
• Manuals:http://www.supermicro.com/support/manuals
• Drivers&Utilities:ftp://ftp.supermicro.com
• Safety:http://www.supermicro.com/about/policies/safety_information.cfm
PaCkage Contents
(Appliestoindividual-packonly)
X9SRi (-F)(-3F) / X9SRE (-F)(-3F)
QuICk referenCe guIde revIsIon 1.0a
• One(1)SupermicroMotherboard
• Eight(8)SATACables
• One(1)I/OShield
• One(1)QuickReferenceGuide
MNL-1284-QRG
© 2012 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
MNL-1284-QRG
JLAN2
3
JSTBY
JCOM1
R625
MH7
MH1
MH5
41
FAN1
41
FAN2
4
1
FAN3
41
FAN4
41
FANA
JVR6
3
JVR5
1
3
JVR4
1
3
JVR3
1
3
JPB1
1
3
JPG1
1
JPL1
1
JPL2
JVR1
13
JVR2
1 3
JWD1
13
JPUSB1
1
JPME_RCV1
3
JPBIOS_RCV1
1
3
DP3
A
C
JI2C1
JI2C2
1
JOH1
1
JCF1
JL1
3-SGPIO2
1
2
7 8
3-SGPIO1
1
2
7
8
T-SGPIO1
2
7
8
T-SGPIO2
1
2
7
8
DIMM_C1
JUSB2
4
PCIX1
PCIX2
PCIX3
JPW1
1
12
24
JBT1
JPI2C1
1
5
SP1
+
PCIE6
PCIE5
PCIE4
X_BT1
JPW2
UID_LED
A
C
UID_SW
1
2
JTPM1
1
2
19
20
SAS4
SAS5 SAS6 SAS7 I-SATA2I-SATA3
I-SATA4
I-SATA5
JKBMS1
+
U8
JWF1
1
3
JTAG1
JD1
17
JF1
1
2
19
20
JVGA
JIPMB1
I-SATA1
I-SATA0
MAC CODE
MAC CODE
Testedto Comply WithFCC Standards FORHOME OR OFFICE USE
SAS CODE
JCOM2
1
5
6
9
JUSB45
2
7
10
JUSB67
1
2
7
JUSB89
1
2
7
10
JRK1
Pin3:PCH_DYN_SKU
Pin2:Ground
OFF:NORMAL
ON:MEIN FORCE UPDATAMODE
I-ButtonHeader 1
Pin1:RAID_KEY_PCH
OFF:NORMAL
ON:RECOVERBIOS
UID
TPM/PORT80
JIPMB1
P1-DIMM4A P1-DIMM4B
P1-DIMM3A P1-DIMM3B
P1-DIMM2A
P1-DIMM2B
P1-DIMM1B P1-DIMM1A
I-SATA5
I-SATA4
I-SATA3 I-SATA2
I-SATA1
I-SATA0
2-3ENable
Power Flash
KB/MOUSE
JPUSB1:USBWake Up
1-2Disable
PWRI2C
JF1
RST
ON
PWR
PWR
FF
FAIL
HDD NIC
1 2
NIC
OH
LED
NMI
PWR
X
PWRLED
SPEAKER
1-3:
4-7:
JD1:
2-3:NMI
JWD1:WatchDog
1-2:RST
LAN1
LAN2
JPL1/2:LAN
2-3Disable
1-2Enable
FAN4
VGA
COM1
USB0/1
INTRUSION
CHASSIS
OFF:SLAVE ON:MASTER JCF1:CompactFlash
Compact
SAS1/SAS3
SAS0/SAS2
3-SGPIO23-SGPIO1
Connectto IPMI
USB2
USB8/9
USB4/5 USB6/7
2-3Disable
JPB:BMC
1-2Enable
JSTBY: Wakeon Lan
COM2
1-2Enable 2-3Disable JPG1:VGA
OFF:DISABLE ON:ENABLE
I2CBus for PCI slot
JI2C1/JI2C2
SLOT4 PCI-E 3.0 X8 (IN X16)
SLOT5 PCI-E 2.0 X4 (IN X16)
SLOT6 PCI-E 3.0 X16
SLOT3 PCI-X 133/100MHZ
SLOT1 PCI-X 133/100MHZ
SLOT2 PCI-X 133/100MHZ
CLOSE 1st
OPEN 1st
JPW2
Socket R
LGA 2011
CPU
The X9SRi/X9SRE motherboard series supports up to 256GB of
1600/1066/1333 MHz ECC/Non-ECC DDR3 DIMMs in eight (8) memory slots
(UDIMM/RDIMM).
Note: For memory optimization, use only DIMM modules that have been validated by Supermicro.
For the latest memory updates, please refer to our website at http://www.supermicro.com/
products/motherboard.
Motherboard Layout and Features Jumpers, Connectors and LED Indicators
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide.
Heatsink Installation Front Panel Control (JF1)
CPU Installation
Back Panel IO Connectors
Memory Support
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
Note: Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, and LED indicators.
=mounting hole
A
B
C
D
E
F
G
HI
DIMMA1
DIMMD2
DIMMB1
DIMMC2
DIMMA2
DIMMD1
DIMMB2
DIMMC1
Note: Up to 256GB of memory are supported. See chapter 2 of the User Manual for
complete memory population information.
A. Mouse F. COM1
B. Keyboard G. VGA
C. IPMI (-F only) H. LAN1
D. USB Port 2 I. LAN2
E. USB Port 1
OPEN1st
Screw #1
Screw #2
Motherboard
Screw #3
Screw #4
Mounting Hole
CPU
Align Socket Keys
Jumpers
Connectors
LED Indicators
DIMM Memory Installation
I-SATA 2.0
I-SATA 3.0
Available on the X9SRE series only. 11,12 JI2C2,JI2C1 SMB to PCI-E Slots On (Enabled)
13 JPG1 Onboard VGA Enable Pins 1-2 (Enabled)
17 JPB1 BMC Enable (for "F" models only) Pins 1-2 (Enabled)
45 JWD1 Watch Dog Reset Pins 1-2 (Reset)
54 JPUSB1 USB Power Select Pins 1-2 (Dual Power)
56, 57 JPL1,JPL2 LAN1,LAN2 Enable Pins 1-2 (Enabled)
58 JPBIOS1 BIOS Recovery Pins 1-2 (Normal)
59 JPME1 Intel ME Mode Select Pins 1-2 (Normal)
61 JBT1 CMOS Clear Short contact pads to reset CMOS
9UID LED UID (Unit ID) LED Blue: Solid On UID: On
14 DP3 IPMI Heartbeat Green/Blinking BMC/IPMI Normal
47 DP2 Power On LED Green: Solid On System is On
1JKBMS1 Backpanel Keyboard and Mouse Port
2JLAN IPMI LAN Port ("F" models only)
3, 4 USB 0/1 USB 2.0 Port 1, USB 2.0 Port 2
5, 16 JCOM1, JCOM2 COM1 Backpanel Serial Port, COM2 Serial Port Header
6JVGA Backpanel VGA Port
7, 8 JLAN1, JLAN2 Backpanel Gbit LAN Ports 1, 2
10 UID_SW Unit ID Switch
15 JSTBY1 Legacy Wake on LAN header
18 JIPMB1 System Management Bus Header for the IPMI Slot
19 JTPM1 Trusted Platform Module (TPM) Header
20,22,23 JUSB 4/5, 6/7, 8/9 Front Accessible USB Connections (via 3 Headers)
21 JOH1 Overheat LED/Fan Fail
24, 25 3-SGPIO1,3-SGPIO2 Serial General Purpose I/O Headers for SAS
26 JUSB2 Internal Type A USB port
27~30, 32~35 SCU0~7 Internal Serial-Attached SCSI/SAS ports ("3" models only)
31,42,49,50,55 FAN A, FAN 3,2,1,4 Internal Fan headers
36,37,38,39 I-SATA 5,4,3,2 SATA 2.0 ports (3Gb/s)
41, 40 I-SATA 0/1 SATA 3.0 ports (6Gb/s)
43 JF1 Front Panel Control Header
44 JTAG1 Factory Reserved
46 JD1 Power LED / Speaker Header (Pins 4~7: External
Speaker)
48 JL1 Chassis Intrusion Header
51 JPI2C1 Power Supply SMBus I2C Header
52 JPW1 24-pin Main ATX Power Connector
53 JPW2 8-pin Secondary Power Connector
60 JSD1 Disk On Module (DOM) Power
62,63 T-SGPIO2,T-SGPIO1 Serial General Purpose I/O Headers for SATA
Motherboard edge
Memory Population Guidelines
When installing memory modules, the DIMM slots should be populated in the
following order: DIMMA1, DIMMB1, DIMMC1, DIMMD1 then DIMMA2, DIMMB2,
DIMMC2, DIMMD2.
• Always use DDR3 DIMM modules of the same size, type and speed.
• Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed
of the slowest DIMM.
• The motherboard will support odd-numbered modules installed (1 ,3 ,5 ,or 7
modules). However, for best memory performance, install DIMM modules in
pairs.
Recommended Population (Balanced)
DIMMA1 DIMMB1 DIMMC1 DIMMD1 DIMMA2 DIMMB2 DIMMC2 DIMMD2 Total
System
Memory
2GB 2GB 4GB
2GB 2GB 2GB 2GB 8GB
2GB 2GB 2GB 2GB 2GB 2GB 2GB 2GB 16GB
4GB 4GB 8GB
4GB 4G 4GB 4GB 16GB
4GB 4GB 4GB 4GB 4GB 4GB 4GB 4GB 32GB
Power Button
OH/Fan Fail LED
1
NIC1 LED
Reset Button
2
Power Fail LED
HDD LED
Power LED
#3~4
#1~2
Vcc
Vcc/UID Switch
Vcc
Vcc/Blue UID LED
Ground
Ground
1920
Vcc
X
Ground NMI
X
Vcc
NIC2 LED
1
2
4
5
6
78
3
9
10
1112
13
14
15
16
17
18
19
20
21
22
23
29
30
32
33
34
35
36 37 38 39
40 41 42 43
44
45
46
47
48
49
24
25
26
27
28
50
51
52 53
55
5657
58
54
DIMMD2
DIMMD1
DIMMC1
DIMMC2
SLOT1
SLOT2
SLOT3
SLOT4
SLOT5
SLOT6
59
60
61 62 63
DIMMA1
DIMMA2
DIMMB2
DIMMB1
31
Supported on models with "F" designation only
Supported on
models with "3"
designation only