for your system to work ProPerly, Please download the aPProPrIate
drIvers/Images/user'smanual from the lInks below:
• Manuals:http://www.supermicro.com/support/manuals
• Drivers&Utilities:ftp://ftp.supermicro.com/CDR_Images/CDR-X9-UP/
• Safety:http://www.supermicro.com/about/policies/safety_information.cfm
A
This motherboard supports up to 32 GB of DDR3 ECC SODIMMs
in 4 SODIMM slots. It supports speeds of up to 1600MHz.
Note: For memory optimization, use only SODIMM modules that have been validated by
Supermicro. For the latest memory updates, please refer to our website at http://www.
supermicro.com/products/motherboard.
Jumper Description Settings (Defaults are in Bold)
JPME2 Intel ME Manufacturing Mode Pins 1-2 (Normal), Pins 1-2 (Intel ME Manuf. Mode)
JPF1 Front Panel LED select Pins2-3 (Normal), Pins 1-2 (Bypass LAN LED)
JPF2 Front Panel RST Button select Pins2-3 (Normal), Pins 1-2 (FR/NMI)
JBT1 Clear CMOS Short contact pads to clear CMOS
JI2C1/JI2C2 SMB to PCI-Express Slots Pins 1-2 (Open: Disabled), (Closed: Enabled)
JPSLOT1 PCI-E Slot select Pins 1-2 (Slot 7), Pins 2-3 (Slot 6)
Connector Description
Back Panel I/O Please see "Back Panel IO Connectors" below, left
JSTBY1 Provides 5V standby power only, and legacy Wake-On-LAN function
USB 2/3 Front Panel USB 2.0 header for USB 2/3
USB 4 Internal Type A USB Port
COM2 Serial Port header (COM2)
JF1 Front Panel control header (see Front Panel Control (JF1) below, right)
JF2 Front Panel control header (see Front Panel Control (JF2) below)
FAN1~FAN6 System Fan power/control headers (FAN1: CPU Fan)
JD1 External Speaker/Buzzer header (Pins 1-3: Power LED, Pins 4-7:Ext Speaker)
JOH1 System Overheat header
JL1 Chassis Intrusion header
JWOR1 Wake-On-Ring header
I-SATA0/I-SATA1 3Gb/s I-SATA connectors for SATA0 and SATA1
JSD1 SATA DOM (Disk-On-Module) power connector
SP1 Internal Speaker/Buzzer
JPW1 Motherboard 24-pin ATX Main Power connector
JPW2 Motherboard 8-pin ATX CPU Power connector
JTPM1 Trusted Platform Module (TPM) header
LED Description Color/State Status
LED5 Power LED Green/Solid System On/Running
Motherboard Layout and Features Jumpers, Connectors and LED Indicators
Jumpers
Connectors
LED Indicators
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide.
Front Panel Control (JF1)
Memory Population Guidelines
When installing memory modules, the DIMM slots should be populated in the
following order: DIMMA2, DIMMB2 and DIMMA1, DIMMB1
Back Panel I/O Connectors
Memory Support
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
DIMM Installation
Note: Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, and LED indicators.
=mounting hole
B
C
