SUPERMICR R
CONTACT INFORMATION
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com/CDR_Images/CDR-X11-UP/
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
© 2015 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written
consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
PACKAGE CONTENTS
X11SSH-F_(-LN4F)
QUICK REFERENCE GUIDE REV. 1.00
• One (1) Supermicro Motherboard
• Six (6) SATA Cables
• One (1) I/O Shield
• One (1) Quick Reference Guide
• Website: www.supermicro.com
• Phone: +1 (408) 503-8000, Fax: +1 (408) 503-8008
FOR YOUR SYSTEM TO WORK PROPERLY, PLEASE DOWNLOAD APPROPRIATE
DRIVERS/IMAGES/USER'SMANUAL FROM THE LINKS BELOW:
MNL-1778-QRG REV 1.00
Connectors
DIMM Memory Installation
Jumpers and Connectors
Back Panel I/O Connectors
Memory Support
Motherboard Layout and Features
Jumpers
CPU Installation
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this
guide. Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,
and LED indicators. Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
Heatsink Installation Front Panel Control (JF1)
LED Indicators
LED Indicators
Power Button
Blue+
(OH/Fan Fail)
1
NIC1 Activity LED
Reset Button
2
Power Fail LED
HDD LED
FP PWRLED
Reset
PWR
3.3 V
ID_UID_SW/3.3V Stby
Red+
(Blue LED Cathode)
Ground
Ground
19 20
3.3V
X
Ground
NMI
X
NIC2 Activity LED
3.3V Stby
3.3V Stby
I/O Back Panel
A. COM1 D. USB Port 1 (2.0) G. LAN 1 J. LAN 4 (-LN4F only)
B. IPMI LAN E. USB Port 6 (3.0) H. LAN 2 K. VGA
C. USB Port 0 (2.0) F. USB Port 7 (3.0) I. LAN 3 (-LN4F only) L. UID Switch
B
L
C
D
EGH
Jumper Description Default Setting
J7 LAN4 LINK ACK (-LN4F only) Off (Disabled)
J8 LAN3 LINK ACK (-LN4F only) Off (Disabled)
JBR1 BIOS Recovery Pins 1-2 (Normal)
JBT1 Clear CMOS See Chpt. 2 in user manual
JI2C1/JI2C2 SMB to PCI Slots Pins 2-3 (Disabled)
JPB1 BMC Enable/Disable Pins 1-2 (Enabled)
JPG1 VGAEnable Pins 1-2 (Enabled)
JPL1-JPL4 LAN1-LAN4 Enable (LAN3/LAN4: for -LN4F only) Pins 1-2 (Enabled)
JPME2 Manufacturing Mode Select Pins 1-2 (Normal)
JWD1 Watch Dog Enable Pins 1-2 (Reset)
Connector Description
BT1 Onboard Battery
COM1/COM2 COM1/COM2 Port Headers
Fan1-Fan4, FanA System/CPU Fan Headers
I-SATA0-I-SATA7 SATA3.0 Connectors via Intel PCH (6Gb/s)
I-SGPIO 1/2 Serial_Link General Purpose I/O Connection Headers 1/2
IPMI_LAN IPMI_Dedicated Gigabit (RJ45) Port
J23 M.2 Socket
JD1 Speaker/Power LED Indicator
JF1 Front Panel Control Header
JIPMB1 4-pin External BMC I2C Header (for an IPMI Card)
JL1 Chassis Intrusion Header
JOH1 Overheat LED Indicator
JPI2C1 Power I2C System Management Bus (Power SMB) Header
JPWR1 24-pin ATX Main Power Connector (Required)
JPWR2 +12V 8-pin CPU power Connector (Required)
JSD1/JSD2 SATADisk On Module (DOM) Power Connectors
JSTBY1 Wake-On-LAN Enable Header
JTPM1 Trusted Platform Module/Port 80 Connector
JUIDB1 UID (Unit Identification) Switch
LAN1-LAN4 Gigabit (RJ45) LAN Ports (LAN3/LAN4: for -LN4F only)
PCI-E (PCH) Slot 4 PCI-Express 3.0 x4in x8 Slot
PCI-E (CPU) Slot 5 PCI-Express 3.0 x8 Slot
PCI-E (CPU) Slot 6 PCI-Express 3.0 x8in x16 Slot
SP1 Internal Speaker/Buzzer
USB 0/1 Back Panel USB 2.0 Ports
USB 2/3 Front Accessible USB 2.0 Headers
USB 4/5 Front Accessible USB 2.0 Headers
USB 6/7 Back Panel USB 3.0 Ports
USB 8/9 Front Accessible USB 3.0 Header
USB 10 USB 3.0 Type-A Header
VGA Back Panel VGA Port
LED Description State Status
LE1 Rear UID LED Blue: On Unit Identified
LE3 PCI-E 3.0 M.2 LED Green: Blinking Active
LEDBMC BMC Heartbeat LED Green: Blinking BMC Normal
LEDPWR Onboard Power LED Green: Solid on Power On
The X11SSH-F_(-LN4F) has four (4) 288-pin DIMM slots that support up to 64GB
of SDRAM 72-bit DDR4 unbuffered ECC 2133/1866/1600/1333MHz memory.
CPU Properly
Installed
Load Lever Locked
into Place
Load Lever
Load Plate
Pin 1
North Center Edge Turn Clockwise
to Lock
Thermal Paste
P
ush Down
Turn Counter-
clockwise to
Unlock Connect the Heatsink Wire to
the CPU Fan Connector
A
