SUPERMICR R
CONTACT INFORMATION
•www.supermicro.com (Email: support@supermicro.com)
•Manuals: http://www.supermicro.com/support/manuals
•Drivers & Utilities: ftp://ftp.supermicro.com
•Safety: http://www.supermicro.com/about/policies/safety_information.cfm
PACKAGE CONTENTS
(Applies to individual-pack only)
X7SLM / X7SLM+
QUICK REFEREN CE GUIDE RE V . 1.00
•One (1) Supermicro Motherboard
•Two (2) SATA Cables
•One (1) Floppy Drive Ribbon Cable
•One (1) IDE Hard Drive Cable
•One (1) I/O Shield
•One (1) Quick Reference Guide
MNL-0981-QRG RE V . 1.00
© 2012 Supermicro Computer Inc. All rights reserved.Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written
consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
X7SLM/X7SLM+
KB/Mouse
USB 0/1
COM1
VGA
JPL1
LAN1
LAN2
JPL2
LAN
CTRL
Fan4
LAN
CTRL
COM2 Floppy
Battery
Super I/O
SPI BIOS
TPM CTRL
USB2
USB3/4 Fan3
JL1
JBT1
JPT1
JWD
JD1
IDE
PWR Extension
JP3
I-SATA0 I-SATA1 I-SATA2 I-SATA3
Fan2
LE1
Speaker
SP1
JOH1
Fan1
8-pin PWR
J41
Fan5
CPU Fan
24-pin PWR
JPW1
Intel 945GC
MCH
CPU
DIMM 1A
DIMM 1B
DDR2 Unbuffered Non-ECC 667/533/400 MHz
Slot6 PCI-E x8
Slot5 PCI 33 MHz
Intel ICH 7
JF1
This motherboard supports up to 2 GB of Unbuffered (UDIMM) Non-ECC DDR2
400/533/667 MHz memory in 2 memory slots.
Note: For memory optimization, use only DIMM modules that have been
validated by Supermicro. For the latest memory updates, please refer to our
website at http://www.supermicro.com/products/motherboard.
Item # Jumper DescriptionDefault
12 JBT1 CMOS Clear See Chapter 2 in User Manual
7, 31 JPL2, JPL1 GLAN 2 and GLAN 1 Enable Pins 1-2 (Enabled)
34 JWD Watch Dog Timer Enable Pins 1-2 (Reset)
35 JPT1 TPM Support Enable (X7SLM+ only) Pins 1-2 (Enabled)
Item # Connector Description
1KB/Mouse PS/2 Keyboard and Mouse
2USB 0/1 Back Panel Universal Serial Bus Ports
3, 8 COM1, COM2 COM Port 1, COM 2 Header
4VGA Video Graphics Port
5, 6 LAN1, LAN2 Ethernet RJ45 (Gigabit LAN) Connectors 1 and 2
9Floppy Floppy Disk Connector
10 Battery Onboard Battery
11 SPI BIOS SPI BIOS Chip
13 JL1 Chassis Intrusion Header
14 USB 2 Internal USB Port
15 USB 3/4 Front Panel USB Connections
17 I-SATA 0~3 SATA Headers
18 PWR EXTENSION (JP3) Power Extension Connector for Add-on card
19 IDE IDE Hard Drive Connector
20 JD1 Power LED/External Speaker Header
21 SP1 Internal Speaker/Buzzer
16, 22, 26, 28, 30 Fans 3, 2, 1, 5, 4 System Cooling Fans 1~4 & CPU Fan (Fan5)
23 JF1 FP Control Panel Header
25 JOH1 Overheat LED Header
27 8-Pin PWR (J41) 12V 8-pin Power Connector (Required)
29 24-Pin PWR (JPW1) ATX 24-pin Power Connector (Required)
Item # LEDDescription Color/State Status
24 LE1 Power LED Green: On System On
Motherboard Layout and Features Jumpers, Connectors and LED Indicators
Jumpers
Connectors
LED Indicators
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide.
Front Panel Control (JF1)
Back Panel IO Connectors
Memory Support
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
DIMM Installation
Note: Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, and LED indicators.
=mounting hole
A
B
C
