Supermicro SUPERSERVER 1028R-MCT User manual

SUPERSERVER
1028R-MCT
1028R-MCTR
USER’S MANUAL
1.0a

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu-
mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn-
ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other repro-
ductive harm.
Manual Revision 1.0a
Release Date: April 11, 2016
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It pro-
vides information for the installation and use of the SuperServer 1028R-MCT/MCTR.
Installation and maintenance should be performed by experienced technicians only.
The SuperServer 1028R-MCT/MCTR is a high-end server based on the SC-
113MFAC2-605CB/SC113MFAC2-R606CB 1U rackmount chassis and the Super
X10DRL-CT dual processor serverboard.
Manual Organization
Chapter 1: Introduction
The rst chapter provides a checklist of the main components included with the
server system and describes the main features of the X10DRL-CT serverboard and
the SC113MFAC2 chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 1028R-MCT/
MCTR into a rack and check out the server conguration prior to powering up the
system.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: Warnings Statements
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 1028R-MCT/MCTR.

SUPERSERVER 1028R-MCT/MCTR User's Manual
iv
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X10DRL-CT serverboard, including
the locations and functions of connections, headers and jumpers. Refer to this
chapter when adding or removing processors or main memory and when recong-
uring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC113MFAC2 server chassis.
You should follow the procedures given in this chapter when installing, removing
or reconguring hard or peripheral drives and when replacing system power supply
modules and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed informa-
tion on running the CMOS Setup Utility.
Appendix A: POST Error Beep Codes
Appendix B: System Specications
v
Preface
Notes

vi
Table of Contents
Chapter 1 Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Serverboard Features ..................................................................................... 1-2
Processors ...................................................................................................... 1-2
Memory ........................................................................................................... 1-2
SAS ................................................................................................................. 1-2
SATA................................................................................................................ 1-2
PCI Expansion Slots ....................................................................................... 1-2
I/O Ports.......................................................................................................... 1-2
1-3 Server Chassis Features ................................................................................ 1-3
System Power................................................................................................. 1-3
Control Panel .................................................................................................. 1-3
Cooling System............................................................................................... 1-3
1-4 Contacting Supermicro.................................................................................... 1-5
Chapter 2 Server Installation
2-1 Overview ......................................................................................................... 2-1
2-2 Unpacking the System .................................................................................... 2-1
2-3 Preparing for Setup......................................................................................... 2-1
Choosing a Setup Location............................................................................. 2-1
2-4 Warnings and Precautions.............................................................................. 2-2
Rack Precautions............................................................................................ 2-2
Server Precautions.......................................................................................... 2-2
Rack Mounting Considerations ....................................................................... 2-3
Ambient Operating Temperature ................................................................ 2-3
Reduced Airow ......................................................................................... 2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading..................................................................................... 2-3
Reliable Ground ......................................................................................... 2-3
2-5 Installing the System into a Rack ................................................................... 2-4
Identifying the Sections of the Rack Rails...................................................... 2-4
Inner Rails....................................................................................................... 2-5
Outer Rails ...................................................................................................... 2-6
Installing the Server into a Telco Rack ........................................................... 2-9
Chapter 3 System Interface
3-1 Overview ......................................................................................................... 3-1
3-2 Control Panel Buttons ..................................................................................... 3-1
Reset............................................................................................................... 3-1
SUPERSERVER 1028R-MCT/MCTR User's Manual
vii
Table of Contents
Power .............................................................................................................. 3-1
UID .................................................................................................................. 3-1
3-3 Control Panel LEDs ........................................................................................ 3-2
NIC2 ................................................................................................................ 3-2
NIC1 ................................................................................................................ 3-2
HDD................................................................................................................. 3-2
Power .............................................................................................................. 3-2
Information LED .............................................................................................. 3-3
3-4 Drive Carrier LEDs.......................................................................................... 3-3
Chapter 4 Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements....................................................... 4-1
Warning Denition ........................................................................................... 4-1
Installation Instructions.................................................................................... 4-4
Circuit Breaker ................................................................................................ 4-5
Power Disconnection Warning........................................................................ 4-6
Equipment Installation..................................................................................... 4-8
Restricted Area................................................................................................ 4-9
Battery Handling............................................................................................ 4-10
Redundant Power Supplies .......................................................................... 4-12
Backplane Voltage ........................................................................................ 4-13
Comply with Local and National Electrical Codes........................................ 4-14
Product Disposal........................................................................................... 4-15
Hot Swap Fan Warning................................................................................. 4-16
Power Cable and AC Adapter ...................................................................... 4-18
Chapter 5 Advanced Serverboard Setup
5-1 Handling the Serverboard ............................................................................... 5-1
Precautions ..................................................................................................... 5-1
Unpacking ....................................................................................................... 5-1
5-2 Processor and Heatsink Installation................................................................ 5-2
Installing a CPU Heatsink ............................................................................... 5-5
5-3 Connecting Cables.......................................................................................... 5-6
Connecting Data Cables ................................................................................. 5-6
Connecting Power Cables .............................................................................. 5-6
Connecting the Control Panel......................................................................... 5-6
5-4 I/O Ports.......................................................................................................... 5-7
5-5 Installing Memory............................................................................................ 5-8
5-6 Adding PCI Cards ......................................................................................... 5-10
5-7 Serverboard Details .......................................................................................5-11
X10DRL-CT Quick Reference........................................................................5-11

viii
SUPERSERVER 1028R-MCT/MCTR User's Manual
5-8 Connector Denitions ................................................................................... 5-13
5-9 Jumper Settings ............................................................................................ 5-20
5-10 Onboard Indicators........................................................................................ 5-23
5-11 SAS/SATA Ports............................................................................................ 5-24
5-12 Installing Software......................................................................................... 5-25
SuperDoctor® 5 ............................................................................................ 5-26
5-13 Onboard Battery............................................................................................ 5-27
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices.................................................................................. 6-1
Precautions ..................................................................................................... 6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 System Cooling............................................................................................... 6-2
System Fan Failure......................................................................................... 6-3
6-4 Drive Bay Installation/Removal ....................................................................... 6-4
Accessing the Drive Bays ............................................................................... 6-4
Hard Drive Installation..................................................................................... 6-4
DVD Drive Installation..................................................................................... 6-6
6-5 Power Supply.................................................................................................. 6-8
Power Supply Failure...................................................................................... 6-8
1028R-MCT................................................................................................ 6-8
1028R-MCTR ............................................................................................. 6-9
Removing/Replacing the Power Supply.......................................................... 6-9
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
Starting BIOS Setup Utility.............................................................................. 7-1
How To Change the Conguration Data ......................................................... 7-1
How to Start the Setup Utility ......................................................................... 7-2
7-2 Main Setup...................................................................................................... 7-2
7-3 Advanced Setup Congurations...................................................................... 7-4
7-4 Event Logs .................................................................................................... 7-29
7-5 IPMI............................................................................................................... 7-31
7-6 Security Settings ........................................................................................... 7-33
7-7 Boot Settings................................................................................................. 7-34
7-8 Save & Exit ................................................................................................... 7-37
Appendix A BIOS Error Beep Codes
Appendix B System Specications

Chapter 1
Introduction
1-1 Overview
The SuperServer 1028R-MCT/MCTR is a high-end server comprised of two main
subsystems: the SC113MFAC2-605CB/SC113MFAC2-R606CB 1U server chassis
and the X10DRL-CT dual processor serverboard. Please refer to our website for
information on operating systems that have been certied for use with the system
(www.supermicro.com).
In addition to the serverboard and chassis, various hardware components have
been included with the 1028R-MCT/MCTR, as listed below:
• Four sets of 4-cm counter-rotating fans (FAN-0154L4)
• Two passive CPU heatsinks (SNK-P0047PD)
• One air shroud for 1U system (MCP-310-19015-0N)
• One riser card for one PCI-E 3.0 x8 PCI add-on card (RSC-RR1U-E8)
• SATA Accessories
One SATA backplane (BPN-SAST-113A-N2)
Eight 2.5" hard drive carriers (MCP-220-00047-0B)
• One rail kit consisting of one set each of outer rails (MCP-290-00102-0N), in-
ner rails (MCP-290-00107-0N) and inner rail extensions (MCP-290-00110-0N)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
• Supermicro product manuals: http://www.supermicro.com/support/manuals/
• Product drivers and utilities: ftp://ftp.supermicro.com
• Product safety info: http://www.supermicro.com/about/policies/safety_informa-
tion.cfm
• If you have any questions, please contact our support team at:
[email protected]m
Chapter 1: Introduction
1-1

1-2 1-3
Chapter 1: Introduction
SUPERSERVER 1028R-MCT/MCTR User's Manual
1-2 Serverboard Features
At the heart of the SuperServer 1028R-MCT/MCTR lies the X10DRL-CT, a dual
processor serverboard based on Intel's PCH C612 chipset. Below are the main
features of the X10DRL-CT (see Figure 1-1 for a block diagram of the chipset).
Processors
The X10DRL-CT supports up to two Intel®Xeon®E5-2600 v3/v4 Series processors
in R3 LGA 2011 sockets. Please refer to the serverboard description pages on our
website for a complete listing of supported processors.
Memory
The X10DRL-CT has eight DIMM sockets that can support up to 1 TB of ECC
LRDIMM (Load Reduced Load DIMMs) or 512 GB of RDIMM (Registered DIMMs)
DDR4-2400/2133/1866/1600 memory. Please refer to Chapter 5 for installing
memory.
SAS
Eight SAS 3.0 ports are supported by the onboard LSI 3108 controller. RAID 0, 1,
5, 6 and 10 supported.
SATA
An on-chip SATA controller is integrated into the X10DRL-CT to provide six SATA
3.0 ports, which are RAID 0, 1, 5 and 10 supported.
PCI Expansion Slots
A riser card (RSC-RR1U-E8) has been pre-installed to the X10DRL-CT to support
one full-height, half-length PCI-E 3.0 x8 PCI expansion card.
I/O Ports
The rear I/O ports include one VGA port, two USB 3.0 ports, two 1 Gb LAN ports,
two 10 Gb LAN ports and a dedicated IPMI LAN port.
1-3 Server Chassis Features
The SC113MFAC2-605CB/SC113MFAC2-R606CB is a short depth (< 20") 1U
chassis that features eight 2.5" hard drive bays. The following is a general outline
of the main features of the SC113MFAC2-605CB/SC113MFAC2-R606CB chassis.
System Power
When congured as the SuperServer 1028R-MCT/MCTR, the SC113MFAC2-605CB
includes a single high-efciency 600W power supply and the SC113MFAC2-
R606CB includes redundant, 600W hot-plug high-efciency power supplies.
Control Panel
The control panel on the SC113MFAC2-605CB/SC113MFAC2-R606CB provides
important system monitoring and control information. LEDs indicate power on,
network activity and hard disk drive activity. Also present are a main power button
and a system reset button.
Cooling System
The chassis' revolutionary cooling design has been optimized to provide sufcient
cooling for dual CPU congurations. The chassis includes four 4-cm counter-
rotating, PWM (Pulse Width Modulated) fans located in the middle of the chassis.
Fan speed is controlled via IPMI.

1-4 1-5
Chapter 1: Introduction
SUPERSERVER 1028R-MCT/MCTR User's Manual
Figure 1-1. Intel PCH 612 Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Website: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [email protected]
Website: www.supermicro.com.tw
SPI
RGMII
Debug Card
CTRL
FAN SPEED
PCI-E X1 G2
USB 2.0 #12 USB2.0
#5/6/7/8
PCH
SATA 3.0
USB 2.0
LPC
#1
#0
#5
#4
RTL8211E-VB-CG
#3
#2
RJ45
BIOS
SPI
SPI
Temp Sensor
W83773G
TPM HEADER
USB 3.0
BIOS
HEADER
SPI
AST2400
BMC
#1
RMII/NCSI
COM1
Header
VGA CONN
BMC BootFlash
DDR3
SLOT 5
5 PHASE
145W
P1
P1
P0
VR12.5
P0
#1-4
#1-3
#1-2
SLOT 6
PCI-E X16 G3
DMI2
4GB/s
PCI-E X16
PCI-E X8 G3
PCI-E X8 G3
2IMD2IMD
SNB CORE
DDR-IV
SNB CORE
DDR-IV
QPI
9.6G
5 PHASE
145W
VR12.5
PCI-E X8
#2CD #1 #2AB#3#3 #2AB#1
#2-2
#2-3
#2-4
<=1.758W (average)
2.3W (Peak)TDP:6.5W (WORKSTATION)
5W (SERVER)
USB & SATA useage different
Idle:0.45W
5V:1.2A
3.3V:0.1A
3.3 STBY:0.2A
1.05 PCH
1.05 ASW
1.5 PCH
PVCCIO 1.0/0.95
3.3STBY:0.5A
PCI-E X8 G3
LAN2
I210
LAN1
#2
#3
#4
PCI-E X8
SLOT 4
#2CD
PCI-E X8 G3
1UPC0UPC
x1 two port header
x1 TypeA connector
x2 rear port
x1 two port header
X540
LSI SAS3108
LAN3/
LAN4
I210
MiniSAS
HD *2
DDR3
SAS 3.0
QPI
9.6G
FRONT PANEL
SATAUSBUSB
1866/2133
DDR4
#2-1
1866/2133
DDR4
#1-1

1-6
SUPERSERVER 1028R-MCT/MCTR User's Manual
Notes

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 1028R-MCT/
MCTR up and running. Following these steps in the order given should enable you to
have the system operational within a minimum amount of time. This quick setup as-
sumes that your SuperServer 1028R-MCT/MCTR system has come to you with the
processors and memory preinstalled. If your system is not already fully integrated
with a serverboard, processors, system memory etc., please turn to the relevant
chapter or section for details on installing specic components.
2-2 Unpacking the System
You should inspect the box the SuperServer 1028R-MCT/MCTR was shipped in and
note if it was damaged in any way. If the server itself shows damage you should
le a damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the SuperServer 1028R-
MCT/MCTR. It should be situated in a clean, dust-free area that is well ventilated.
Avoid areas where heat, electrical noise and electromagnetic elds are generated.
You will also need it placed near a grounded power outlet. Read the Rack and
Server Precautions in the next section.
2-3 Preparing for Setup
The box the SuperServer 1028R-MCT/MCTR was shipped in should include two
sets of rail assemblies, two rail mounting brackets and the mounting screws you
will need to install the system into the rack. Follow the steps in the order given to
complete the installation process in a minimum amount of time. Please read this
section in its entirety before you begin the installation procedure outlined in the
sections that follow.
Choosing a Setup Location
• Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufcient airow and ease in servicing.This product is for

Chapter 2: Server Installation
2-32-2
SUPERSERVER 1028R-MCT/MCTR User's Manual
installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).
• This product is not suitable for use with visual display work place devices
acccording to §2 of the the German Ordinance for Work with Visual Display Units.
2-4 Warnings and Precautions
Rack Precautions
• Ensure that the leveling jacks on the bottom of the rack are fully extended to
the oor with the full weight of the rack resting on them.
• In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
• Always make sure the rack is stable before extending a component from the
rack.
• You should extend only one component at a time - extending two or more si-
multaneously may cause the rack to become unstable.
Server Precautions
• Review the electrical and general safety precautions in Chapter 4.
• Determine the placement of each component in the rack before you install the
rails.
• Install the heaviest server components on the bottom of the rack rst, and then
work up.
• Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
• Allow the hot plug SATA drives and power supply modules to cool before touch-
ing them.
• Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating tempera-
ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera-
ture (Tmra).
Reduced Airow
Equipment should be mounted into a rack so that the amount of airow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec-
tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).
Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
• When mounting this unit in a partially lled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.

Chapter 2: Server Installation
2-52-4
SUPERSERVER 1028R-MCT/MCTR User's Manual
2-5 Installing the System into a Rack
This section provides information on installing the SuperServer 1028R-MCT/MCTR
into a rack. Note: The rails will t a rack between 26" and 33.5" deep.
There are a variety of rack units on the market, which may mean the assembly
procedure will differ slightly. The following is a guideline for installing the 1028R-
MCT/MCTR into a rack with the rack rails provided. You should also refer to the
installation instructions that came with the rack unit you are using.
Identifying the Sections of the Rack Rails
Each assembly consists of two sections: an inner xed chassis rail that secures
directly to the server chassis and an outer xed rack rail that secures directly to
the rack itself.
Figure 2-1. Identifying the Sections of the Rack Rails
Inner Rails
Inner Rail Extensions
Figure 2-2. Installing Chassis Rails
Inner Rails
The SC113MFAC2 chassis includes a set of inner rails in two sections: inner rails
and inner rail extensions. The inner rails are pre-attached and do not interfere with
normal use of the chassis if you decide not to use a server rack. Attach the inner
rail extension to stabilize the chassis within the rack.
Installing the Inner Rails (Figure 2-2)
1. Place the inner rack extensions on the side of the chassis aligning the hooks
of the chassis with the rail extension holes. Make sure the extension faces
"outward" just like the pre-attached inner rail.
2. Slide the extension toward the front of the chassis.
3. Secure the chassis with two screws as illustrated.
4. Repeat steps 1-3 for the other inner rail extension.
1
2
3
Stability hazard. The rack stabilizing mechanism must be in place, or the
rack must be bolted to the oor before you slide the unit out for servicing.
Failure to stabilize the rack can cause the rack to tip over.
Warning: do not pick up the server with the front handles. They are de-
signed to pull the system from a rack only.

Chapter 2: Server Installation
2-72-6
SUPERSERVER 1028R-MCT/MCTR User's Manual
Outer Rails
Installing the Outer Rails to the Rack (Figures 2-3 and 2-4)
1. Attach the short bracket to the outside of the long bracket. You must align the
pins with the slides. Also, both bracket ends must face the same direction.
2. Adjust both the short and long brackets to the proper distance so that the rail
ts snugly into the rack.
3. Secure the long bracket to the front side of the outer rail with two M5 screws
and the short bracket to the rear side of the outer rail with three M5 screws.
4. Repeat steps 1-4 for the left outer rail.
Figure 2-3. Assembling the Outer Rails
SCALE 0.500
Secure to the
Front of the Rack
Secure to the
Rear of the Rack
Attach Outer Rails
Together
SCALE 0.380
Figure 2-4. Installing the Outer Rails to the Rack
2
3
3
Slide rail mounted equipment is not to be used as a shelf or a work space.
Note: The gure above is for illustration purposes only. Always install servers to
the bottom of the rack rst.

Chapter 2: Server Installation
2-92-8
SUPERSERVER 1028R-MCT/MCTR User's Manual
Figure 2-5. Installing the Server into a Rack
Installing the Chassis into a Rack (Figure 2-5)
1. Conrm that chassis includes the inner rails and rail extensions . Also, conrm
that the outer rails are installed on the rack.
2. Line chassis rails with the front of the rack rails.
3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click".
4. (Optional) Insert and tightening the thumbscrews that hold the front of the
server to the rack.
Installing the Server into a Telco Rack
To install the SuperServer 1028R-MCT/MCTR into a Telco type rack, use two L-
shaped brackets on either side of the chassis (four total). First, determine how far
follow the server will extend out the front of the rack. Larger chassis should be
positioned to balance the weight between front and back. If a bezel is included on
your server, remove it. Then attach the two front brackets to each side of the chas-
sis, then the two rear brackets positioned with just enough space to accommodate
the width of the telco rack. Finish by sliding the chassis into the rack and tightening
the brackets to the rack.
Figure 2-6. Installing the Server into a Telco Rack
Note: The gure above is for illustration purposes only. Always install servers to
the bottom of the rack rst.
Note: The gure above is for illustration purposes only. Always install servers to
the bottom of the rack rst.

2-10
SUPERSERVER 1028R-MCT/MCTR User's Manual
Notes

Chapter 3: System Interface
3-1
Chapter 3
System Interface
3-1 Overview
There are several LEDs on the control panel to keep you constantly informed of the
overall status of the system as well as the three buttons described below.
3-2 Control Panel Buttons
There are three buttons located on the front of the chassis: a UID button, a reset
button and a power on/off button.
Reset
Use the reset button to reboot the system.
Power
This is the main power button, which is used to apply or turn off the main system
power. Turning off system power with this button removes the main power but keeps
standby power supplied to the system.
UID
Depressing the UID (unit identier) button illuminates an LED on both the front and
rear of the chassis for easy system location in large stack congurations. The LED
will remain on until the button is pushed a second time. Another UID button on the
rear of the chassis serves the same function. This button has an LED built into it,
which will illuminate when either the front or rear UID button is pushed.

Chapter 3: System Interface
3-2 3-3
SUPERSERVER 1028R-MCT/MCTR Manual
NIC1
Indicates network activity on LAN1 when ashing.
NIC2
Indicates network activity on LAN2 when ashing.
HDD
Indicates SATA and/or peripheral drive activity when ashing.
Power
Indicates power is being supplied to the system's power supply units. This LED
should normally be illuminated when the system is operating.
3-3 Control Panel LEDs
The control panel located on the front of the SC113MFAC2 chassis has ve LEDs.
These LEDs provide you with critical information related to different parts of the
system. This section explains what each LED indicates when illuminated and any
corrective action you may need to take. Information LED
This LED will be solid blue when the UID function has been activated. When this
LED ashes red, it indicates a fan failure. When red continuously it indicates an
overheat condition, which may be caused by cables obstructing the airow in the
system or the ambient room temperature being too warm. Check the routing of
the cables and make sure all fans are present and operating normally. You should
also check to make sure that the chassis covers are installed. Finally, verify that
the heatsinks are installed properly (see Chapter 5). This LED will remain ashing
or on as long as the indicated condition exists.
Universal Information LED States
State Indication
Fast Blinking Red (1x/sec) Fan Fail
Solid Red CPU Overheat
Slow Blinking Red (1x/4 sec) Power Fail
Solid Blue Local UID Button Depressed
Blinking Blue IPMI-Activated UID
3-4 Drive Carrier LEDs
The chassis includes externally accessible SATA drives. Each drive carrier displays
two status LEDs on the front of the carrier.
LED Color State Status
Activity LED Green Solid On SATA drive installed
Green Blinking I/O activity
Status LED
Red Solid On Failed drive for SATA with RSTe
support
Red Blinking at 1 Hz Rebuild drive for SATA with
RSTe support
Red
Blinking with two
blinks and one stop
at 1 Hz
Hot spare for SATA with RSTe
support
Red On for ve
seconds, then off
Power on for SATA with RSTe
support
Red Blinking at 4 Hz Identify drive for SATA with
RSTe support

3-4
SUPERSERVER 1028R-MCT/MCTR Manual
Notes

4-1
Chapter 4: Warning Statements for AC Systems
Chapter 4
Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certied technicians should attempt to install or congure
components.
Read this appendix in its entirety before installing or conguring components in the
Supermicro chassis.
These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.
Warning Denition
Warning!
This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
警告の定義
この警 告サインは危険を意味します。
人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、
電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。
此警告符号代表危险。
您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分
意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。
此警告符號代表危險。
您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸
電的危險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。

4-2
SUPERSERVER 1028R-MCT/MCTR User's Manual
4-3
Warning Statements for AC Systems
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie benden sich in einer Situation, die zu
Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes
de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
nal de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES.
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
gurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la n de chaque avertissement.
CONSERVEZ CES INFORMATIONS.
안전을 위한 주의사항
경고!
이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준 작업절차를
준수해 주시기 바랍니다.
해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.
BEWAAR DEZE INSTRUCTIES
.   !




ןונקת תורהצהאהרהז
ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח
ה וא תולאש שיו הדימב .תירשפא תיזיפי ,יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק
רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תאה .םיביכר
אורקל שי .ורקימרפוס יזראמב םיביכרה תרדגה וא תנקתה ינפל ואולמב חפסנה תא