Supero X10SL7-F User manual

SUPERMICR R
ContaCt InformatIon
MNL-1463-QRG
• www.supermicro.com(Email:[email protected])
• Manuals:http://www.supermicro.com/support/manuals
• Drivers&Utilities:ftp://ftp.supermicro.com
• Safety:http://www.supermicro.com/about/policies/safety_information.cfm
© 2012 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
PaCkage Contents
X10sL7-f
QuICk referenCe guIde
• One(1)SupermicroMotherboard
• Six(6)SATACables
• One(1)I/OShield
• One(1)QuickReferenceGuide
MNL-1463-QRG
Connector Description
Battery Onboard Battery
COM1/COM2 COM1 (Port)/COM2 (Header)
Fan1 - Fan4, FanA System/CPU Fan Headers
JF1 Front Panel Control Header
JL1 Chassis Intrusion Header
JLED1 Power LED Indicator Header
JPI2C1 Power SMB (System Management Bus)
JPW1 24-pin ATX Main Power Connector (Required)
JPW2 +12V 8-pin CPU power Connector (Required)
JSD1 SATA DOM (Device_On_Module) Power Connector
JSTBY1 Standby Power Header
JTPM1 Trusted Platform Module/Port 80 Connector
LAN1/LAN2 Gigabit (RJ45) Ports (LAN1/2)
IPMI_LAN IPMI_Dedicated LAN
I-SATA0/I-SATA1 (Intel PCH) Serial ATA (SATA 3.0) Ports 0/1 (6Gb/sec)
I-SATA 2 - I-SATA5 (Intel PCH) Serial ATA (SATA 2.0) Ports 2~5 (3Gb/sec)
L-SAS 0-7 SAS Connectors 0-7 (supported by the LSI 2308 SAS controller)
(PCH) Slot 5 PCI-Express 2.0 x4 in x8 Slot
(CPU) Slot 6 PCI-Express 3.0 x8 in x16 Slot
SPKR1 Internal Speaker/Buzzer
SW1 UID (Unit Identier) Switch
6-SGPIO 1/2 Serial_Link General Purpose I/O Headers 1/2 for SAS Connections
T-SGPIO 1/2 Serial_Link General Purpose I/O Headers 1/2 for SATA Connections
USB 2/3, 4/5 Backpanel USB 2.0 Ports 2/3, 4/5
USB 0,1 (3.0) USB 3.0 Ports 0, 1 (USB 0: Type A Connector)
USB 8/9 Front Panel Accessible USB 2.0 Headers 8/9
VGA Backpanel VGA Port
Jumpers, Connectors and LED Indicators
Back Panel I/O Connectors
Memory Support
Motherboard Layout and Features
Note: Item numbers are listed in counterclockwise order.
IPMI CODE
SAS CODE
BIOS LICENSE
BAR CODE
MAC CODE
FAN2
FAN3
FAN1
FAN4
FANA
JBR1
JPL2
JPS1
JPUSB1 JPL1
JWD1
JLED1
JPB1
JPG1 JPME1
JPME2
J19
J18
LE3
LE5
LE4
JPW1
JPW2
J21
JI2C1
JI2C2
J3
L-SAS0 L-SAS1
L-SAS2 L-SAS3
L-SAS4 L-SAS5
L-SAS6
JPI2C1
JTPM1
6-SGPIO1
T-SGPIO1
T-SGPIO2
JSD1
SPKR1
JBT1
SW1
CPU SLOT6 PCI-E 3.0 X8 (IN X 16)
USB1 (3.0)
USB0 (3.0)
COM2
USB8/9
_LAN
IPMI
VGA COM1
LAN2
JL1
LAN1
DIMMB2
DIMMA2
USB4/5
CPU
JF1
USB2/3
I-SATA3
I-SATA4
I-SATA2
I-SATA1
I-SATA0
I-SATA5
PCH SLOT5 PCI-E 2.0 X4 (IN X 8)
DIMMB1
DIMMA1
JSTBY1
L-SAS7
6-SGPIO2
Battery
PCH
SAS
CTRL
LAN
CTRL
LAN
CTRL
BMC
X10SL7-F
Rev. 1.01
CPU1
BIOS
Front Panel CTRL
JOH1
LEDS2
LE6
Jumpers
CPU Installation
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide. Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,
and LED indicators.
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
= mounting hole
Heatsink Installation Front Panel Control (JF1)
DIMM Memory Installation
Connectors
LED Indicators
Load Plate
Load Lever
North Center
Edge
South
Center Edge
Pin 1
CPU Properly
Installed
Load Lever Locked
into Place
Thermal Grease
Heatsink Fan
1. Push Down
2. Turn
Clockwise
to lock; Turn
Counter-
clockwise to
unlock
3. Connect Fan
Cables to onboard
Fan Headers
Tools Needed:
Pan Head #6 screws (8)
Standoff (If needed)
Jumper Description Default
JBT1 CMOS Clear (See Chpt. 2)
JI2C1/JI2C2 SMB to PCI-E Slots Pins 2-3 (Disabled)
JPG1 VGA Enable Pins 1-2 (Enabled)
JPL1/JPL2 LAN1/LAN2 Enable Pins 1-2 (Enabled)
JPME1 ME Recovery Pins 1-2 (Normal)
JPME2 Manufacture Mode Select Pins 1-2 (Normal)
JPS1 SAS Enable Pins 1-2 (Enabled)
JPUSB1 USB 4/5 Wake_up Enable Pins 1-2 (Enabled)
JWD1 Watch Dog Enable Pins 1-2 (Reset)
LED Description Color/State Status
LE3 Standby Power LED On: Power On
LE4 UID LED Blue (On): Unit Identied
LE5 BMC Heartbeat LED Green (Blinking): BMC Normal
LE6 Power Status LED Red: PWR Fail/Yellow: Standby PWR Active/Green: PWR On Normal
LEDS2 SAS LED Green (Blinking): SAS Active/Red (Solid On): SAS Error
The X10SL7-F supports up to 32GB of Unbuffered (UDIMM) DDR3 ECC
1600/1333 MHz in 4 memory slots. Populating these DIMM modules with a pair
of memory modules of the same type and same size will result in interleaved
memory, which will improve memory performance.
Memory Population Guidelines
Please follow the table below when populating the X10SL7-F.
DDR3 Unbuffered ECC (UDIMM) Memory
DIMM Slots per
Channel
DIMMs Populat-
ed per Channel
DIMM Type POR Speeds Ranks per DIMM (any
combination)
2 1 Unbuffered
DDR3
1333, 1600 Single Rank, Dual Rank
2 2 Unbuffered
DDR3
1333, 1600 Single Rank, Dual Rank
Channel A Slot1
Channel A Slot2
Channel B Slot1
Channel B Slot2
Towards the CPU
Towards the Edge of the Motherboard
Release Tabs
Notches
Power Button
OH/Fan Fail LED
1
NIC1 LED
Reset Button
2
HDD LED
Power LED
Reset
PWR
Vcc
Vcc
Vcc
Vcc
Ground
Ground
1920
Vcc
X
Ground NMI
X
Vcc
PWR Fail LED
NIC2 LED
COM1
USB 2 (2.0)
USB 3 (2.0)
IPMI_LAN
USB 4 (2.0)
USB 5 (2.0)
LAN1 LAN2 VGA