Supero SUPERSERVER 5018D-MTF User manual

SUPERSERVER
5018D-MTF
5018D-MTRF
SUPER ®
USER’S MANUAL
1.0

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu-
mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILLSUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATASTORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn-
ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other repro-
ductive harm.
Manual Revision 1.0
Release Date: June 17, 2013
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2013 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperServer 5018D-
MTF/5018D-MTRF. Installation and maintenance should be performed by experi-
enced technicians only.
The SuperServer 5018D-MTF/5018D-MTRF is a high-end server based on the
SC813MTQ-350CB/SC813MTQ-R400CB 1U rackmount chassis and the Super
X10SLM-F single processor motherboard.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the
server system and describes the main features of the X10SLM-F motherboard and
the SC813MTQ-350CB/SC813MTQ-R400CB chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 5018D-
MTF/5018D-MTRF into a rack and check out the server configuration prior to
powering up the system. If your server was ordered without processor and memory
components, this chapter will refer you to the appropriate sections of the manual
for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.

SUPERSERVER 5018D-MTF/5018D-MTRF User's Manual
iv
Chapter 4: Standardized Warning Statements
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 5018D-MTF/5018D-MTRF.
Chapter 5: Advanced Motherboard Setup
Chapter 5 provides detailed information on the X10SLM-F motherboard, including
the locations and functions of connections, headers and jumpers. Refer to this
chapter when adding or removing processors or main memory and when reconfig-
uring the motherboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC813MTQ-350CB/SC813MTQ-
R400CB server chassis. You should follow the procedures given in this chapter when
installing, removing or reconfiguring SATA or peripheral drives and when replacing
system power supply modules and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed informa-
tion on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: System Specifications

v
Preface
Notes

vi
Table of Contents
Chapter 1 Introduction
1-1 Overview .........................................................................................................1-1
1-2 Motherboard Features.....................................................................................1-2
Processors ......................................................................................................1-2
Memory ...........................................................................................................1-2
Serial ATA........................................................................................................1-2
I/O Ports..........................................................................................................1-2
1-3 Server Chassis Features ................................................................................1-3
System Power................................................................................................. 1-3
SATA Subsystem............................................................................................. 1-3
Control Panel .................................................................................................. 1-3
Cooling System............................................................................................... 1-3
1-4 Contacting Supermicro....................................................................................1-5
Chapter 2 Server Installation
2-1 Overview .........................................................................................................2-1
2-2 Unpacking the System....................................................................................2-1
2-3 Preparing for Setup......................................................................................... 2-1
Choosing a Setup Location............................................................................. 2-1
2-4 Warnings and Precautions.............................................................................. 2-2
Rack Precautions............................................................................................ 2-2
Server Precautions..........................................................................................2-2
Rack Mounting Considerations....................................................................... 2-3
Ambient Operating Temperature................................................................2-3
Reduced Airflow .........................................................................................2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading..................................................................................... 2-3
Reliable Ground ......................................................................................... 2-3
2-5 Installing the System into a Rack ...................................................................2-4
Identifying the Sections of the Rack Rails......................................................2-4
Installing the Rear Inner Rails ........................................................................2-4
Installing the Rack Rails .................................................................................2-5
Installing the Server into the Rack.................................................................. 2-6
Installing the Server into a Telco Rack...........................................................2-7
Chapter 3 System Interface
3-1 Overview .........................................................................................................3-1
3-2 Control Panel Buttons..................................................................................... 3-1
SUPERSERVER 5018D-MTF/5018D-MTRF User's Manual

vii
Table of Contents
Reset...............................................................................................................3-1
Power..............................................................................................................3-1
3-3 Control Panel LEDs ........................................................................................3-2
Overheat/Fan Fail ........................................................................................... 3-2
NIC2................................................................................................................3-2
NIC1................................................................................................................3-2
HDD................................................................................................................. 3-2
Power..............................................................................................................3-3
3-4 Hard Drive Carrier LEDs.................................................................................3-3
Chapter 4 Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements....................................................... 4-1
Warning Definition...........................................................................................4-1
Installation Instructions.................................................................................... 4-4
Circuit Breaker ................................................................................................ 4-5
Power Disconnection Warning........................................................................4-6
Equipment Installation..................................................................................... 4-8
Restricted Area................................................................................................ 4-9
Battery Handling............................................................................................ 4-10
Redundant Power Supplies .......................................................................... 4-12
Backplane Voltage ........................................................................................ 4-13
Comply with Local and National Electrical Codes........................................ 4-14
Product Disposal........................................................................................... 4-15
Hot Swap Fan Warning................................................................................. 4-16
Power Cable and AC Adapter ...................................................................... 4-18
Chapter 5 Advanced Motherboard Setup
5-1 Handling the Motherboard ..............................................................................5-1
Precautions .....................................................................................................5-1
Unpacking .......................................................................................................5-1
5-2 Processor and Heatsink Installation................................................................5-2
Installing an LGA 1150 Processor................................................................... 5-2
Installing a Passive CPU Heatsink .................................................................5-4
Removing the Heatsink...................................................................................5-4
5-3 Connecting Cables.......................................................................................... 5-7
Connecting Data Cables.................................................................................5-7
Connecting Power Cables .............................................................................. 5-7
Connecting the Control Panel.........................................................................5-7
5-4 I/O Ports..........................................................................................................5-8
5-5 Installing Memory............................................................................................ 5-9

viii
SUPERSERVER 5018D-MTF/5018D-MTRF User's Manual
5-6 Adding PCI Cards......................................................................................... 5-12
5-7 Motherboard Details...................................................................................... 5-13
X10SLM-F Quick Reference......................................................................... 5-13
5-8 Connector Definitions ...................................................................................5-15
5-9 Jumper Settings............................................................................................ 5-21
5-10 Onboard Indicators........................................................................................5-24
5-11 SATA Drive Connections............................................................................... 5-25
5-12 Installing Software......................................................................................... 5-26
SuperDoctor III.............................................................................................. 5-27
5-13 Onboard Battery............................................................................................ 5-28
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices..................................................................................6-1
Precautions .....................................................................................................6-1
Unpacking .......................................................................................................6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 System Fans................................................................................................... 6-3
6-4 Drive Bay Installation/Removal....................................................................... 6-3
Removing the Front Bezel..............................................................................6-3
SATA Drive Installation....................................................................................6-4
Accessing the Drive Bays...............................................................................6-4
SATA Backplane.............................................................................................. 6-5
6-5 Power Supply.................................................................................................. 6-7
5018D-MTF Power..........................................................................................6-7
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
Starting BIOS Setup Utility..............................................................................7-1
How To Change the Configuration Data......................................................... 7-1
How to Start the Setup Utility .........................................................................7-2
7-2 Main Setup...................................................................................................... 7-2
7-3 Advanced Setup Configurations......................................................................7-4
7-4 Event Logs....................................................................................................7-23
7-5 Boot Settings................................................................................................. 7-27
7-6 Security Settings........................................................................................... 7-29
7-7 Save & Exit ................................................................................................... 7-30
Appendix A BIOS Error Beep Codes
Appendix B System Specifications

Chapter 1
Introduction
1-1 Overview
The SuperServer 5018D-MTF/5018D-MTRF is a high-end server comprised of two
main subsystems: the SC813MTQ-350CB/SC813MTQ-R400CB 1U server chassis
and the X10SLM-F single processor motherboard. Please refer to our web site for
information on operating systems that have been certified for use with the system
(www.supermicro.com).
In addition to the motherboard and chassis, various hardware components have
been included with the 5018D-MTF/5018D-MTRF, as listed below:
• Four 4-cm fans (FAN-0065L4)
• One passive CPU heatsink (SNK-P0046P)
• One riser card for one PCI-E 3.0 x8 PCI add-on card in a PCI-E 3.0 x16 slot
(RSC-RR1U-E16)
• One rackmount kit (CSE-PT52)
Chapter 1: Introduction
1-1

1-2
SUPERSERVER 5018D-MTF/5018D-MTRF User's Manual
1-2 Motherboard Features
At the heart of the SuperServer 5018D-MTF/5018D-MTRF lies the X10SLM-F, a
single processor motherboard based on the Intel® C224 chipset. Below are the
main features of the X10SLM-F (see Figure 1-1 for a block diagram of the chipset).
Processors
The X10SLM-F supports a single Intel®Core™ i7/i5/i3 DT or Intel® Xeon® E3-1200
v3 or Intel® Xeon® E3-1200 v3 processor in an LGA1150 socket. Please refer to
the motherboard description pages on our web site for a complete listing of sup-
ported processors.
Memory
The X10SLM-F has four DIMM sockets that can support up to 32 GB of Unbuffered
ECC/non-ECC DDR3-1600/1333 memory. Please refer to Chapter 5 for installing
memory.
Serial ATA
An on-chip SATA controller is integrated into the X10SLM-F to provide four SATA
3.0 (6 Gb/s) ports and two SATA 2.0 (3 Gb/s) ports.
I/O Ports
The rear I/O ports include one COM port, a VGA (monitor) port, four USB 2.0 ports,
and two gigabit Ethernet ports. A dedicated IPMI LAN port is also included.

1-3
Chapter 1: Introduction
1-3 Server Chassis Features
The SC813MTQ-350CB/SC813MTQ-R400CB is a 1U rackmount server chassis.
The following is a general outline of the main features of the chassis.
System Power
When configured as a SuperServer 5018D-MTF, the SC813MTQ chassis includes
a single 350W power supply. When configured as a SuperServer 5018D-MTRF, the
SC813MTQ chassis includes a redundant 400W power supply.
SATA Subsystem
For the 5018D-MTF/5018D-MTRF, the SC813MTQ chassis was designed to sup-
port four SATA hard drives, which are hot-swappable units.
Control Panel
The SC813MTQ's control panel provides important system monitoring and control
information. LEDs indicate power on, network activity, hard disk drive activity and
system overheat conditions. The control panel also includes a main power button
and a system reset button. The front of the SC813MTQ also includes a COM port
and two USB serial ports for easy access.
Cooling System
The SC813MTQ chassis has an innovative cooling design that features four 4-cm
high-performance system cooling fans. Each of these fans plug into a chassis fan
header on the motherboard.
Fan speed is controlled by IPMI to be determined by system temperature.

1-4
SUPERSERVER 5018D-MTF/5018D-MTRF User's Manual
Figure 1-1. Intel C224 Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
3 PHASE
VR12.5
#B-0
#B-1
Haswell-DT
4 CORE DDR-III
DMI
PCI-E X16 G3
PCI-E x16
PCI-E X8 G3
PCI-E x8(x16)
PCI-E x8
BOM Select (Default: 2 *8)
DMI x4 G2
#5/6/7/8 PCH
Lynx Point
C222 / C224
6.0 Gb/S
USB 2.0
LPC
#1
#0
SATA
PCI-E X4 G2 3.0 Gb/S
#5
#4
#3
#2
SATA
TPM HEADER
USB 3.0
PCI-E x4(x8)
BIOS
HEADER
SPI
LAN2
Clarkville
i217LM
PCI-E X1 G2
RJ45
LAN1
Springville
i210AT
PCI-E X1 G2
RJ45
AST2400 / 1400
BMC
#3
#2
#1
RMII/NCSI
COM1
Connector COM2 Header
VGA CONN
BMC Boot Flash
DDR3
SPI
LAN3
RGRMII
Debug Card
FRONT PANEL
SYSTEM POWER
CTRL
FAN SPEED
PCI-E X1 G2
USB 2.0
#2 USB2.0
#0-15
#0-7
#8-15
RTL8211E-VB-CG
RJ45
X10SLx: AST1400
X10SLx-F: AST2400
X10SLL: C222
X10SLM: C224
BIOS
SPI
SPI
Temp Sensor
EMC1402-1 *2 at diff SMBUS
up to 1600
#A-1
DDRIII
#A-0
USBUSB
Note: two chipsets are shown - the C224 applies to the X10SLM-F.

1-5
Chapter 1: Introduction
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Pacific
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 23511
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [email protected]
Tel: [phone]

1-6
SUPERSERVER 5018D-MTF/5018D-MTRF User's Manual
Notes

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 5018D-
MTF/5018D-MTRF up and running. Following the steps in the order given should
enable you to have the system operational within a minimal amount of time. This
quick setup assumes that your 5018D-MTF/5018D-MTRF system has come to you
with the processor and memory preinstalled. If your system is not already fully
integrated with a motherboard, processor, system memory etc., please turn to the
chapter or section noted in each step for details on installing specific components.
2-2 Unpacking the System
You should inspect the box the SuperServer 5018D-MTF/5018D-MTRF was shipped
in and note if it was damaged in any way. If the server itself shows damage, you
should file a damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the SuperServer 5018D-
MTF/5018D-MTRF. It should be situated in a clean, dust-free area that is well
ventilated. Avoid areas where heat, electrical noise and electromagnetic fields are
generated. You will also need it placed near a grounded power outlet. Read the
Rack and Server Precautions in the next section.
2-3 Preparing for Setup
The box the SuperServer 5018D-MTF/5018D-MTRF was shipped in should include
two sets of rail assemblies, six rail mounting brackets and the mounting screws
you will need to install the system into the rack. Follow the steps in the order given
to complete the installation process in a minimal amount of time. Please read this
section in its entirety before you begin the installation procedure outlined in the
sections that follow.
Choosing a Setup Location
• Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufficient airflow and ease in servicing.This product is for

2-2
SUPERSERVER 5018D-MTF/5018D-MTRF User's Manual
installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).
• This product is not suitable for use with visual display work place devices
acccording to §2 of the the German Ordinance for Work with Visual Display Units.
2-4 Warnings and Precautions
Rack Precautions
• Ensure that the leveling jacks on the bottom of the rack are fully extended to
the floor with the full weight of the rack resting on them.
• In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
• Always make sure the rack is stable before extending a component from the
rack.
• You should extend only one component at a time - extending two or more si-
multaneously may cause the rack to become unstable.
Server Precautions
• Review the electrical and general safety precautions in Chapter 4.
• Determine the placement of each component in the rack before you install the
rails.
• Install the heaviest server components on the bottom of the rack first, and then
work up.
• Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
• Allow the hot plug SATA drives and power supply modules to cool before touch-
ing them.
• Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation
2-3
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating tempera-
ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera-
ture (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec-
tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).
Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
• When mounting this unit in a partially filled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.

2-4
SUPERSERVER 5018D-MTF/5018D-MTRF User's Manual
2-5 Installing the System into a Rack
This section provides information on installing the SuperServer 5018D-MTF/5018D-
MTRF into a rack unit with the rack rails provided. If the server has already been
mounted into a rack, you can skip ahead to Sections 2-5 and 2-6.
There are a variety of rack units on the market, which may mean the assembly
procedure will differ slightly. You should also refer to the installation instructions that
came with the rack unit you are using.
Identifying the Sections of the Rack Rails
You may have received rack rail hardware with the SuperServer 5018D-MTF/5018D-
MTRF. (Two front inner rails should already be attached to the chassis.) This
hardware consists of two rear inner rails that secure to the chassis, one on each
side just behind the preinstalled front inner rails. Note that these two rails are left/
right specific.
Installing the Rear Inner Rails
First, locate the right rear inner rail (the rail that will be used on the right side of
the chassis when you face the front of the chassis). Align the two square holes on
the rail against the hooks on the right side of the chassis. Securely attach the rail
to the chassis with M4 flat head screws. Repeat these steps to install the left rear
inner rail to the left side of the chassis (see Figure 2-1). You will also need to attach
the rail brackets when installing into a telco rack.
Locking Tabs: Both chassis rails have a locking tab, which serves two functions.
The first is to lock the server into place when installed and pushed fully into the
rack, which is its normal position. Secondly, these tabs also lock the server in place
when fully extended from the rack. This prevents the server from coming completely
out of the rack when you pull it out for servicing.

Chapter 2: Server Installation
2-5
Installing the Rack Rails
Determine where you want to place the SuperServer 5018D-MTF/5018D-MTRF in
the rack (see Rack and Server Precautions in Section 2-3). Position the chassis
rail guides at the desired location in the rack, keeping the sliding rail guide facing
the inside of the rack. Screw the assembly securely to the rack using the brackets
provided. Attach the other assembly to the other side of the rack, making sure that
both are at the exact same height and with the rail guides facing inward.
Figure 2-1. Installing Rear Inner Chassis Rails
Warning: do not pick up the server with the front handles. They are de-
signed to pull the system from a rack only.

2-6
SUPERSERVER 5018D-MTF/5018D-MTRF User's Manual
Figure 2-2. Installing the Server into a Rack
(with optional front bezel shown)
Installing the Server into the Rack
You should now have rails attached to both the chassis and the rack unit. The next
step is to install the server into the rack. Do this by lining up the rear of the chassis
rails with the front of the rack rails. Slide the chassis rails into the rack rails, keeping
the pressure even on both sides (you may have to depress the locking tabs when
inserting). See Figure 2-2.
When the server has been pushed completely into the rack, you should hear the
locking tabs "click".
Stability hazard. The rack stabilizing mechanism must be in place, or the
rack must be bolted to the floor before you slide the unit out for servicing.
Failure to stabilize the rack can cause the rack to tip over.