Supero SUPERSERVER 6027TR-HTRF+ User manual

®
SUPER
SUPERSERVER
Revision 1.0
SUPERSERVER
6027TR-HTRF+
6027TR-H70RF+
6027TR-H71RF+

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILLSUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATASTORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 1.0
Release Date: December 31, 2012
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2012 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperServer
6027TR-HTRF+/H70RF+/H71RF+. Installation and maintainance should be
performed by experienced technicians only.
The SuperServer 6027TR-HTRF+/H70RF+/H71RF+ are all high-end servers
based on the SC827HQ-R1620B 2U rackmount chassis and the dual processor
X9DRT-HF+ serverboard. All models have an IPMI LAN port and four serverboard
nodes with three hot-swap Hard Disk Drives (HDD) each per node.
Each of the various models of the SuperServer 6027TR-HTRF+/H70RF+/H71RF+
servers contains the same X9DRT-HF+ serverboard. The systems differ in the type
of RAID chip system mounted in the system on their HDD adapter cards, as listed
in the table below:
SUPERSERVER 6027TR-HTRF+/H70RF+/H71RF+ Model Variations
Server Model SAS RAID Chip System HDD Adapter Card
SuperServer 6027TR-HTRF+ No SAS BPN-ADPX9-6SATA-O-P
SuperServer 6027TR-H70RF+ LSI SAS2008 BPN-ADP-SAS2-L6I-O-P
SuperServer 6027TR-H71RF+ LSI SAS2108 BPN-ADP-SAS2-H6IR-O-P
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the
server system and describes the main features of the X9DRT-HF+ serverboard and
the SC827HQ-R1620B chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer
6027TR-HTRF+/H70RF+/H71RF+ into a rack and check out the server configuration
prior to powering up the system. If your server was ordered without processor and
memory components, this chapter will refer you to the appropriate sections of the
manual for their installation.

SUPERSERVER 6027TR-HTRF+/H70RF+/H71RF+ User's Manual
iv
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SUPERSERVER 6027TR-HTRF+/H70RF+/H71RF+.
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X9DRT-HF+ serverboard, including
the locations and functions of connections, headers and jumpers. Refer to
this chapter when adding or removing processors or main memory and when
reconfiguring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC827HQ-R1620B server chassis.
You should follow the procedures given in this chapter when installing, removing
or reconfiguring SAS/SATA or peripheral drives and when replacing system power
supply units and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed information
on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: System Specifications

v
Notes
Preface

vi
Table of Contents
Chapter 1 Introduction
1-1 Overview .........................................................................................................1-1
1-2 Serverboard Features..................................................................................... 1-2
Processors ......................................................................................................1-2
Memory ...........................................................................................................1-2
Serial ATA ....................................................................................................... 1-2
SAS.................................................................................................................1-3
PCI Expansion Slots....................................................................................... 1-3
Onboard Controllers/Ports .............................................................................. 1-3
Graphics Controller......................................................................................... 1-3
Other Features................................................................................................1-3
1-3 Server Chassis Features ................................................................................1-4
System Power................................................................................................. 1-4
SAS/SATA Subsystem..................................................................................... 1-4
Front Control Panel.........................................................................................1-4
I/O Ports..........................................................................................................1-4
Cooling System...............................................................................................1-4
Air Shrouds ..................................................................................................... 1-5
Mounting Rails ................................................................................................ 1-5
1-4 Advanced Power Management.......................................................................1-5
Intel® Intelligent Power Node Manager (NM).................................................1-5
Manageability Engine (ME)............................................................................. 1-5
1-5 Contacting Supermicro....................................................................................1-7
1-6 2U Twin2: System Notes .................................................................................1-8
Nodes..............................................................................................................1-8
System Power................................................................................................. 1-8
SAS/SATA Backplane/Drives ..........................................................................1-8
Chapter 2 Server Installation
2-1 Overview .........................................................................................................2-1
2-2 Unpacking the System.................................................................................... 2-1
2-3 Preparing for Setup.........................................................................................2-1
2-4 Warnings and Precautions.............................................................................. 2-2
Choosing a Setup Location............................................................................. 2-2
Rack Precautions............................................................................................ 2-2
Server Precautions..........................................................................................2-2
SUPERSERVER 6027TR-HTRF+/H70RF+/H71RF+ User's Manual

vii
Rack Mounting Considerations.......................................................................2-3
Ambient Operating Temperature................................................................2-3
Reduced Airflow .........................................................................................2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading..................................................................................... 2-3
Reliable Ground ......................................................................................... 2-3
2-5 Installing the System into a Rack ...................................................................2-4
Separating the Sections of the Rack Rails.....................................................2-4
Installing the Inner Rail Extension..................................................................2-5
Outer Rack Rails.............................................................................................2-6
2-6 Checking the Serverboard Setup.................................................................... 2-8
2-7 Checking the Drive Bay Setup........................................................................ 2-9
Chapter 3 System Interface
3-1 Overview .........................................................................................................3-1
3-2 Control Panel Button.......................................................................................3-2
3-3 Control Panel LEDs ........................................................................................3-2
3-4 Drive Carrier LEDs..........................................................................................3-3
SAS/SATA Drives............................................................................................ 3-3
Chapter 4 Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements.......................................................4-1
Warning Definition...........................................................................................4-1
Installation Instructions.................................................................................... 4-4
Circuit Breaker ................................................................................................ 4-5
Power Disconnection Warning........................................................................ 4-6
Equipment Installation.....................................................................................4-8
Restricted Area................................................................................................ 4-9
Battery Handling............................................................................................ 4-10
Redundant Power Supplies .......................................................................... 4-12
Backplane Voltage ........................................................................................ 4-13
Comply with Local and National Electrical Codes........................................4-14
Product Disposal........................................................................................... 4-15
Hot Swap Fan Warning................................................................................. 4-16
Power Cable and AC Adapter ...................................................................... 4-18
Chapter 5 Advanced Motherboard Setup
5-1 Handling the Motherboard ..............................................................................5-1
Precautions .....................................................................................................5-1
Unpacking .......................................................................................................5-1
5-2 Connecting Cables..........................................................................................5-2
Table of Contents

viii
Connecting Data Cables................................................................................. 5-2
5-3 Rear I/O Ports.................................................................................................5-2
5-4 Processor and Heatsink Installation................................................................5-3
Installing a Passive CPU Heatsink .................................................................5-7
Removing the Passive Heatsink.....................................................................5-8
5-5 Installing Memory............................................................................................5-9
Memory Support..............................................................................................5-9
Maximum Memory........................................................................................... 5-9
DIMM Module Population Configuration ...................................................5-11
5-7 Motherboard Details...................................................................................... 5-13
5-8 Connector Definitions.................................................................................... 5-16
5-9 Jumper Settings............................................................................................ 5-19
Explanation of Jumpers ................................................................................5-19
5-10 Onboard Indicators........................................................................................5-21
5-11 PCI-Express and Serial ATA Connections....................................................5-23
5-12 Installing Drivers............................................................................................ 5-24
Supero Doctor III........................................................................................... 5-25
5-13 Onboard Battery............................................................................................ 5-27
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices..................................................................................6-1
Precautions .....................................................................................................6-1
Unpacking .......................................................................................................6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 Chassis Cover................................................................................................. 6-3
6-4 Air Shrouds ..................................................................................................... 6-4
6-5 Checking the Airflow ....................................................................................... 6-5
6-6 System Fans................................................................................................... 6-5
Optional Fan Configurations...........................................................................6-5
6-7 Removing and Installing the Backplane.......................................................... 6-8
Removing the Backplane................................................................................ 6-8
Installing the Backplane................................................................................ 6-10
6-8 Installing the Motherboard .............................................................................6-11
I/O Shield .......................................................................................................6-11
Permanent and Optional Standoffs................................................................6-11
6-9 Adapter Card/Micro-LP Card Replacement.................................................. 6-14
Micro-LP Card/Micro-LP Slot Setup..............................................................6-15
6-10 Drive Bay Installation/Removal.....................................................................6-16
SUPERSERVER 6027TR-HTRF+/H70RF+/H71RF+ User's Manual

Accessing the Drive Bays............................................................................. 6-16
6-11 Power Supply................................................................................................6-20
Power Supply Replacement.......................................................................... 6-20
Power Supply Replacement.......................................................................... 6-20
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
Starting BIOS Setup Utility..............................................................................7-1
How To Change the Configuration Data......................................................... 7-1
Starting the Setup Utility................................................................................. 7-2
7-2 Main Setup......................................................................................................7-2
7-3 Advanced Settings Menu................................................................................ 7-3
7-4 Event Logs.................................................................................................... 7-26
7-5 IPMI............................................................................................................... 7-28
7-6 Boot...............................................................................................................7-30
7-7 Security ......................................................................................................... 7-31
7-8 Save & Exit ................................................................................................... 7-32
Appendix A BIOS Error Beep Codes
Appendix B System Specifications
ix
Table of Contents

x
Notes
SUPERSERVER 6027TR-HTRF+/H70RF+/H71RF+ User's Manual

Chapter 1
Introduction
1-1 Overview
The SuperServer 6027TR-HTRF+/H70RF+/H71RF+ is a high-end server comprised
of two main subsystems: the SC827HQ-R1620B 2U server chassis and the
X9DRT-HF+ dual processor serverboard in four hot-swap nodes. Please refer to
our web site for information on operating systems that have been certified for use
with the system (www.supermicro.com).
In addition to the serverboard and chassis, various hardware components have
been included with the SuperServer 6027TR-HTRF+/H70RF+/H71RF+ server, as
listed below:
• Four (4) Plastic air shrouds (MCP-310-82719-0B)
• Heat Sinks
Four (4) 1U passive CPU heat sinks (SNK-P0047PSM)
Four (4) 1U passive CPU heat sinks w/narrow ILM (SNK-P0047PS)
• Four (4) 80x80x38mm cooling fans (FAN-0129L4)
• SATA/SAS Backplane
One (1) SAS Backplane for 12 3.5" HDD (BPN-SAS-827HQ)
Twelve (12) hot-swap 3.5" HDD trays (MCP-220-00075-0B)
6027TR-HTRF+ Only:
Eight (8) 29-cm 30AWG SATA cables (CBL-0483L)
Four (4) 6-port SATA adapter cards (BPN-ADPX9-6SATA-O-P)
6027TR-H70RF+ Only:
Four (4) SAS2 LSI2008 HD adapter cards (BPN-ADP-SAS2-L6I-O-P)
6027TR-H71RF+ Only:
Four (4) SAS2 LSI2108 HD adapter cards (BPN-ADP-SAS2-H6IR-O-P)
• One (1) rails set (MCP-290-00053-0N)
Note: a complete list of safety warnings is provided on the Supermicro web site at
http://www.supermicro.com/about/policies/safety_information.cfm
Chapter 1: Introduction
1-1

1-2
SUPERSERVER 6027TR-HTRF+/H70RF+/H71RF+ User's Manual
1-2 Serverboard Features
At the heart of the 6027TR-HTRF+/H70RF+/H71RF+ server
lies the X9DRT-HF+, a dual processor serverboard based on the Intel®
C602 chipset and designed to provide maximum performance. four of these
serverboards can be mounted in the SC827HQ-R1620B chassis.
The sections below cover the main features of the X9DRT-HF+ serverboard (see
Figure 1-1 for a block diagram of the chipset).
Processors
The X9DRT-HF+ supports single or dual Intel Xeon®E5-2600 series processors
(Socket R LGA 2011). Please refer to the serverboard description pages on our
web site for a complete listing of supported processors (www.supermicro.com).
Memory
The X9DRT-HF+ has sixteen (16) DIMM slots supporting up to 512 GB of
DDR3-1600/1333/1066/800 MHz speed registered ECC SDRAM in up to
512 MB, 1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB sizes at 1.35V or 1.5V
voltages. See Chapter 5 for details.
Note: Check the Supermicro website (www.supermicro.com) for the latest memory
support information.
Serial ATA
A Serial ATA controller is integrated into each node's C602 chipset to provide up to
a six 6-port SATA subsystem. Two SATA 3 ports are available on the serverboard
(SATA 0/1) and a six port BPN-ADPX9-6SATA-O-P adapter card is mounted for
each serverboard node. RAID 0, 1, 5 and 10 are supported. The SATA drives are
hot-swappable units.
Note: The operating system you use must have RAID support to enable the hot-
swap capability and RAID function of the SATA drives.

1-3
Chapter 1: Introduction
SAS
An LSI®SAS2008 or SAS2108 SAS2 controller is integrated into the installed
BPN-ADP-SAS2-L6I-O-P (6027TR-H70RF+) or BPN-ADP-SAS2-H6IR-O-P
(6027TR-H71RF+) adapter cards to provide support for three 6 Gb/s SAS2 (Serial
AttachedSCSI) subsystemsfor eachnode.The systemhasRAID0,1 and10 support
(RAID5 withoptionalAOC-SAS2-RAID5-KEY)fortheSuperServer 6027TR-H70RF+
or RAID 0, 1 and 5 support for the SuperServer 6027TR-H71RF+ server. The SAS
drives are hot-swappable units.
Note: The operating system you use must have RAID support to enable the
hotswap capability and RAID function of the SAS drives.
PCI Expansion Slots
The SuperServer 6027TR-HTRF+/H70RF+/H71RF+ has for each node one (1)
PCI-E 3.0 x8 Slot for SMC-Proprietary Micro LP Card (CPU1 Slot2) and one (1)
PCI-E 3.0 x8 Slot for SMC-Proprietary Daughter (Add-On) Card (CPU1 Slot1).
Onboard Controllers/Ports
The color-coded I/O ports include a VGA (monitor) port, two USB 2.0 ports (an
additional internal USB header and one Type A USB connector are included on the
serverboard), an IPMI 2.0 dedicated LAN port and two Ethernet ports.
Note: For IPMI Configuration Instructions, please refer to the Embedded BMC
Configuration User's Guide available @ http://www.supermicro.com/support/
manuals/ for IPMI 2.0 system.
Graphics Controller
The X9DRT-HF+ features an integrated Matrox®G200eW Video Controller.
Other Features
Other onboard features that promote system health include onboard voltage
monitors, a chassis intrusion header, auto-switching voltage regulators, chassis and
CPU overheat sensors, virus protection, node manager software and BIOS rescue.

1-4
SUPERSERVER 6027TR-HTRF+/H70RF+/H71RF+ User's Manual
1-3 Server Chassis Features
The following is a general outline of the main features of the SC827 server chassis.
System Power
Each SC827 chassis model includes a high-efficiency 80-plus Platinum certified
power supply, rated at 1620 Watts plus one redundant backup power supply.
In the unlikely event your power supply fails, replacement is simple and can be
accomplished without tools.
SAS/SATA Subsystem
The SC827 supports up to twelve (12) 3.5" hot-swap SAS/SATA drives in trays
(3 for each node). These drives are hot-swappable units and are connected to a
backplane that provides power and control.
Note: The operating system you use must have RAID support to enable the hot-
swap capability of the drives.
Front Control Panel
SC827HQ-R1620B chassis includes four front panels on the handles of the chassis
which control each of the systems. Each control panel on the SUPERSERVER
6027TR-HTRF+/H70RF+/H71RF+ provides you with system monitoring and control
for one server node. LEDs indicate system power, HDD activity, network activity,
system overheat and power supply failure. Amain power button and a system reset
button are also included.
I/O Ports
The SC827 is an proprietary form factor chassis designed to be used in a 2U
rackmount configuration. The SC827 chassis provides a low-profile add-on card
slot, a COM port, a VGA port, two USB 2.0 ports , one IPMI Ethernet port and two
gigabit Ethernet ports per node.
Cooling System
The SC827 chassis accepts four system fans powered from either backpane
or the serverboards. If not powered from the backpane, the SC827HQ-R1620B
model chassis powers four fans from four motherboards, so that when one of the
motherboard drawers is removed, the other motherboards will continue running
all fans.

1-5
Chapter 1: Introduction
Air Shrouds
The SC827 chassis includes four plastic air shrouds that direct the airflow where
cooling is needed on each serverboard. Always use the air shroud included with
your chassis on each serverboard.
Mounting Rails
The SC827 includes a set of quick-release rails, and can be placed in a rack for
secure storage and use. To setup your rack, follow the step-by-step instructions
included in this manual.
1-4 Advanced Power Management
Intel® Intelligent Power Node Manager (NM)
The Intel® Intelligent Power Node Manager (IPNM) provides your system with
real-time thermal control and power management for maximum energy efficiency.
Although IPNM Specification Version 1.5 is supported by the BMC (Baseboard
Management Controller), your system must also have IPNM-compatible
Manageability Engine (ME) firmware installed to use this feature.
Manageability Engine (ME)
The Manageability Engine, which is an ARC controller embedded in the IOH (I/O
Hub), provides Server Platform Services (SPS) to your system. The services
provided by SPS are different from those proveded by the ME on client platforms.

1-6
SUPERSERVER 6027TR-HTRF+/H70RF+/H71RF+ User's Manual
Figure 1-1. Intel C602 Chipset:
System Block Diagram
Note: This is a general block diagram and may not exactly repre-
sent the features on your motherboard. See the previous pages for
the actual specifications of your motherboard. This block diagram is
intended for your reference only.
#2
#2
#2
#2
#2 #2 #2
#2
PROCESSOR
SANDYBRIDGE
PROCESSOR
SANDYBRIDGE
QPI
DDR3 DIMM
DDR3 DIMM
DDR3 DIMM
DDR3 DIMM
#1
G
SSB
PATSBURG
PEG0
DMI
PEG1_1
PEG1_8
PCI-32bit
USB
LAN
I350
2 ports
AT25321
LPC
CPU FRONT
FAN Side
CPU REAR
(I/O Side)
USB
REAR
HDR 2X5
0,1
TPM Header
USB Type-A
2,3
U7C1
U6H1
H
F
E
Socket 0
Socket 1
#1
P0
P0
P1
P1
PE3 PE2 PE1 DMI
PE3 PE2 PE1 DMI
Gen3
x8
x4
VGA BMC
WPCM450
DDR2
PHY1
LAN
RTL8201F
SPI
SATA
Gen2
PCI-E x8 MicroLP SLOT
x4
RJ45 RJ45
Gen3
x8 Gen3
x8
PCI-E x8 in x4 SLOT
x8
x1
x8(0..7)
HOTSWAP INTERFACE
SATA2 #5
SATA2 #4
SATA2 #3
SATA2 #2
SATA3 #1
SATA3 #0
PORT6
PORT5
PORT4
PORT3
PORT2
PORT1
6/3/1.5
QPI
VGA CONN
DDR3 DIMM
DDR3 DIMM
#1
C
#1
D
DDR3 DIMM
DDR3 DIMM
A
B
#1 #1
#1 #1
J1
J2

1-7
Chapter 1: Introduction
1-5 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Pacific
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd
Chung-Ho Dist., New Taipei City 235
Taiwan
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [email protected]
Tel: [phone]

1-8
SUPERSERVER 6027TR-HTRF+/H70RF+/H71RF+ User's Manual
1-6 2U Twin2: System Notes
As a 2U Twin2configuration, the SuperServer 6027TR-HTRF+/H70RF+/H71RF+ is
a unique server system. With four system boards incorporated into a single chassis
acting as four separate nodes, there are several points you should keep in mind.
Nodes
Each of the four serverboards act as a separate node in the system.As independant
nodes, each may be powered off and on without affecting the others. In addition,
each node is a hot-swappable unit that may be removed from the rear of the chassis.
The nodes are connected to the server backplane by means of an adapter card.
Note:Aguide pin is located between the upper and lower nodes on the inner chassis
wall. This guide pin also acts as a “stop” when a node is fully installed. If too much
force is used when inserting a node this pin may break off. Take care to slowly slide
a node in until you hear the “click” of the locking tab seating itself.
System Power
Dual 1620 Watt power supplies are used to provide the power for all four
serverboards. Each serverboard however, can be shut down independently of the
other with the power button on its own control panel.
SAS/SATA Backplane/Drives
As a system, the SuperServer 6027TR-HTRF+/H70RF+/H71RF+ supports the use
of twelve SAS/SATA drives. A single SAS/SATA backplane works to apply system-
based control for power and fan speed functions, yet at the same time logically
connects a set of three SAS/SATA drives to each serverboard. Consequently, RAID
setup is limited to a three-drive scheme (RAID cannot be spread across all twelve
drives). See the Drive Bay Installation/Removal section in Chapter 6 for the logical
hard drive and node configuration.

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer
6027TR-HTRF+/H70RF+/H71RF+ up and running. Following these steps in the
order given should enable you to have the system operational within a minimum
amount of time. This quick setup assumes that your system has come to you with the
processors and memory preinstalled. If your system is not already fully integrated
with a serverboard, processors, system memory etc., please turn to the chapter or
section noted in each step for details on installing specific components.
2-2 Unpacking the System
You should inspect the box the SuperServer 6027TR-HTRF+/H70RF+/H71RF+ was
shipped in and note if it was damaged in any way. If the server itself shows damage
you should file a damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the SuperServer
6027TR-HTRF+/H70RF+/H71RF+. It should be situated in a clean, dust-free area
that is well ventilated. Avoid areas where heat, electrical noise and electromagnetic
fields are generated. You will also need it placed near a grounded power outlet.
Read the Rack and Server Precautions in the next section.
2-3 Preparing for Setup
The box the SuperServer 6027TR-HTRF+/H70RF+/H71RF+ was shipped in should
include two sets of rail assemblies, two rail mounting brackets and the mounting
screws you will need to install the system into the rack. Follow the steps in the
order given to complete the installation process in a minimum amount of time.
Please read this section in its entirety before you begin the installation procedure
outlined in the sections that follow.

2-2
SUPERSERVER 6027TR-HTRF+/H70RF+/H71RF+ User's Manual
2-4 Warnings and Precautions
Choosing a Setup Location
• Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufficient airflow and ease in servicing.
• This product is for installation only in a Restricted Access Location (dedicated
equipment rooms, service closets and the like).
• This product is not suitable for use with visual display work place devices
acccording to §2 of the the German Ordinance for Work with Visual Display Units.
Rack Precautions
• Ensure that the leveling jacks on the bottom of the rack are fully extended to
the floor with the full weight of the rack resting on them.
• In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
• Always make sure the rack is stable before extending a component from the
rack.
• You should extend only one component at a time - extending two or more
simultaneously may cause the rack to become unstable.
Server Precautions
• Review the electrical and general safety precautions in Chapter 4.
• Determine the placement of each component in the rack before you install the
rails.
• Install the heaviest server components on the bottom of the rack first, and then
work up.
• Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
• Allow any hot plug drives and power supply modules to cool before touching
them.
• Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.