SUPRO 1605R Reverb User manual

Model 1605R Reverb
User Manual
All contents c Absara Audio LLC 2014

1. Important Safety Information
The triangle surrounding an exclama-
tion mark alerts users to the presence
of important warnings or information.
The triangle surrounding a lightning
bolt alerts users to the presence of
dangerous high-voltage within the en-
closure of the product that can pose
a significant risk of electrical shock.
•Read these instructions
•Keep these instructions
•Heed all warnings
•Follow all instructions
•Do not use this apparatus near water
•Clean only with dry cloth
•Do not block any ventilation openings. Install in accordance with the manufacturers instructions.
•Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
•Do not defeat the safety purpose of the grounding-type plug. A grounding type plug has two
blades and a third grounding prong. The third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
•Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
•Only use the attachments/accessories specified by the manufacturer.
•Use only the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
•Unplug this apparatus during lightning storms or when unused for long periods of time.
•Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
•To insure proper ventilation always make sure there is at minimum four inches (101.6mm) of
space behind the rear of the apparatus. The ventilation should not be impeded by covering the
ventilation openings with items, such as newspapers, tablecloths, curtains, etc. Do not impede
ventilation by placing objects on top of the apparatus which extend past the rear edge of its
cabinet.
•Please contact Supro directly or a qualified person for tube replacement
•The AC plug is the mains disconnect. The plug should remain accessible after installation.
•WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
moisture.
•WARNING: The apparatus shall not be exposed to dripping or splashing and that objects filled
with liquid, such as vases, shall not be placed on apparatus.
•Caution: To reduce the risk of fire or electric shock, do not remove the cover or back of the
product. There are no user serviceable parts inside. Refer service to qualified personnel.
1

Contents
1 Important Safety Information 1
Contents 2
2 Anatomy and Usage 3
2.1 FrontPanel ........................................ 3
2.2 RearPanel......................................... 4
2.3 SettingTones ....................................... 5
2.4 SuggestedRigs ...................................... 5
2.5 Tubes ........................................... 9
2.6 Troubleshooting ...................................... 9
3 Supro Warranty Policy 10
3.1 USA/CanadaWarranty .................................. 10
3.2 International Warranty: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2

2. Anatomy and Usage
2.1 Front Panel
IN
Instrument input.
GAIN
Input GAIN. Controls the saturation of the preamp stage.
TREBLE
Controls the amount of treble in your signal.
BASS
Controls the amount of bass in your signal.
REVERB
Controls the amount of reverb in the signal.
BYPASS
Footswitch jack to allow remote reverb kill. Use a standard, latching 1/4 TS footswitch.
MASTER
Master volume. Controls volume to speaker.
STANDBY SWITCH
This turns on the high voltage to the tubes. The tubes should warm up for at least one minute before
turning standby switch to OPERATE. Be sure that the Volume control is set to a reasonable position
before switching the amplifier to OPERATE as this amplifier can be very loud! For short breaks (5
minutes or less), using the standby switch will increase tube life.
PILOT LIGHT
This shows that AC Mains voltage is flowing to the amplifier.
POWER SWITCH
Turns on AC power to the amplifier. The Power switch should be turned on, and the pilot light should
be lit for 1 minute before turning the standby switch to OPERATE.
3

2.2 Rear Panel
Speaker Out
The 1605R Reverb provides one 8 Ohm, and two 4 Ohm speaker outputs.
•Use the 8 output for the internal speaker, OR, a single 8 external cabinet, without the internal
speaker.
•To use the internal speaker AND an extension cabinet, plug the internal speaker in to one of
the 4 jacks, and extension into the other 4 jack.
Always be sure a speaker is plugged into at least one of the outputs! Never turn the
amplifier on without a speaker plugged in!
Dry Out
Dry signal output. This output provides the dry signal only, which may be routed to a separate
amplifier or a console. Plugging into this jack, removes the Dry signal from the signal sent to the
power amp, AND the Mix Out.
Reverb Out
Wet signal output only. Provides a Reverb only signal, which may be sent to an additional amplifier
or console. Plugging into this jack, removes the reverb signal from the signal sent to the power amp,
AND the Mix Out.
Mix Out
Provides Dry and Reverb signals together, the level of which is controlled by the ”Mix Out Level”.
Plugging into this jack will not interrupt the signal going to the power amplifier.
Mix Out Level
Controls the level of the Mix Out signal.
Power Amp Input
Accepts a line level signal to be sent the 1605Rs power section. The volume of this signal will be
controlled by the Master volume.
4

IEC POWER CORD RECEPTACLE / Fuse holder
The power cord connects here and to your country’s appropriate wall outlet. Make sure to connect
the male end of the IEC POWER CORD into a Grounded Power Outlet. This IEC connector contains
the AC Mains fuse. This is a 5x20mm, 2.5A, 250V Fuse.
2.3 Setting Tones
The Supro 1605R Reverb amplifier is a 5-Watt, 1x8 combo amp with tube-driven spring reverb. This
ultra-compact and gig-ready amplifier provides independent gain and master volume controls, along
with a 2-band EQ and three tube-driven line-outputs optimized for feeding another guitar amplifier or
recording console. The trio of line outputs is driven by the preamp tubes - before the master volume
- allowing the player to tame the on-board speaker down from gig volume to be used as a bedroom
rig, as well as an all-tube outboard gain/reverb effect unit and direct recording preamp.
Plugging into the first input, labeled ”HI”, provides maximum input gain. The ”LO” input provides
slightly less input stage gain, and therefore a bit more headroom.
The WET output provides 100% wet reverb signal; the DRY output provides 100% dry signal from
the preamp; and the MIX output carries a blend of dry and reverb signals that can be attenuated by a
variable level control on the MIX output. When the WET output is used, the reverb signal is removed
from the on-board speaker output, allowing the player to pass the reverb sound along to another
amplifier while still hearing the gain from the 1605R’s tube preamp in the on-board 8” speaker. When
the DRY output is used, the unaffected sound of the guitar is removed from the on-board speaker
output, allowing the player to pass the gained up dry sound along to another amplifier while still
hearing the reverb effect in the on-board 8” speaker.
Supro amplifiers are some of the most dynamically sensitive guitar amplifier ever designed. The player
is able to access a myriad of sounds within this amplifier by turning the volume(s) up to the point of
glorious overdrive and simply controlling the strength of the signal right from the volume knob on the
guitar.
2.4 Suggested Rigs
5

Supro 1605R Reverb Supro 1606 Super
Reverb Only Dry Only
with Additional Gain from the 1605R
Plug your guitar into the 1605R, and plug a cable from the “Dry Out” to the input of the 1606 Super.
The Master Volume controls the volume of the reverb, while the Super’s single knob controls
the Dry volume. This configuration provides maximum gain, with additional tone shaping provided
by the 1605R preamp, as well as independent blending of the reverb and dry signals.
Figure 2.1: The Supro 1605R/1606 Wet/Dry Micro Stack
6

Supro 1605R Reverb
Dry Only
Plug guitar into 1605R Reverb. Connect “Reverb Out” directly to console.
Mic the cabinet, and connect this to the console.
This configuration gives you the dry signal, through the cabinet and your favorite mic,
plus the reverb signal, pre-power amp , direct to the console.
Figure 2.2: Just one of many Recording Options...
7

Supro 1605R Reverb
Plug guitar into the 1605R Reverb. Connect the “Mix Out” to the guitar input
of your favorite stage amp, or the input of a power amp.
This configuration offers the amazing tone of the 1605R Reverb, with added volume!
Figure 2.3: One louder!
8

2.5 Tubes
Each Supro tube amplifier is a 100% analog, 100% tube amplifier. There are NO solid state (transistor)
devices in ANY audio signal path.
ECC81
V2
Reverb
Driver
ECC83
V4
Rev. Make-up Gain
Viewed from the rear of the chassis
Power
Transformer
Output
Transformer
Power Tube
6L6
ECC83
V1
V2
Preamp
Reverb
Return
Reverb
Send
Supro 1605R Reverb
2.6 Troubleshooting
Supro products have been designed for years of trouble free service. There are many unique protection
features to the design. If you are having difficulty, check the following:
No sound, but PILOT LIGHT is ON
Check to see that the speaker is plugged into the SPEAKER JACK. Make sure all knobs are turned
up past zero and that the standby switch is set to operate. As this is a tube amplifier, the tubes take
approximately 1 minute to warm up before you will get sound. The STANDBY switch should be set
to standby for this warm up period.
No sound and the Lights are All OFF
Unplug the power cord and check the 2.5A, 250V fuse (rear panel).
If you have any further questions, our email address is [e-mail].
9

3. Supro Warranty Policy
3.1 USA/Canada Warranty
To Validate the Warranty on your Supro tube amplifier, please register the product online at
http://suprousa.com/warranty/.
This warranty applies only to the original retail purchaser when this amplifier is purchased from an
Authorized Supro Dealer and is subject to the limitations set forth herein.
Important: Please retain your original sales receipt, as it is your proof of purchase validating this
limited warranty.
This Warranty shall cover the following components as below:
•Amplifiers: 1 year, extended* to 2 years
•Speaker enclosures: 1 year, extended* to 2 years
•Tubes and Speakers: 90 days
*Note: The extended warranty will be automatically applied when you register online at
http://suprousa.com/warranty/. The extended warranty period is only applicable if the above form
is submitted prior to the expiration of the initial 1 year warranty which begins at the date of purchase.
It is your responsibility to submit this information and we shall not be liable nor do we accept any
responsibility whatsoever for non-receipt of this information.
What is Covered:
Defects in the materials and/or workmanship of your product which has been purchased through an
authorized Supro USA dealer. This Warranty shall be applicable when the original sales receipt or
proof of purchase of the Product is presented together with the defective Product.
What is not Covered:
Damage caused by negligence, modification, improper use, incorrect voltages or general wear and tear.
Damage caused during transportation of the product. Damage caused by repair or service carried out
by persons not authorized by Supro USA. A Product with a serial number which has been defaced,
removed etc. A Product which was not purchased from an Authorized Dealer in the USA or Canada.
Warranty Service:
The Warranty Service may include repairs or replacement of the Product in accordance with the terms
set out herein. If we are unable to repair the defective Product, we reserve the right to provide you
with a replacement which may or may not be a reconditioned Product.
Do not attempt to repair the device because this voids the warranty.
In the event a repair or replacement has been made, we shall be entitled to take and keep possession
of the defective Product which is deemed to be beyond repair during the Warranty Period.
Providing the defective Product is covered by the terms of this Warranty we shall be responsible for
the cost of returning your unit to you.
10

How to Obtain Warranty/Non-Warranty Service:
•Complete the service email form available at
http://suprousa.com/support/.
•You will receive a Supro USA Return Authorization form from a Supro support technician.
•You must download, print and complete the Supro USA Return Authorization form. Provide the
info requested on this form, and include a copy of the original purchase receipt. Please enclose
these two documents with your amplifier, and ship to the Supro USA service dept:
Supro USA
200 Wilson St. BLDG F
Port Jefferson Station, NY 11776
For amplifiers owned less than 30 days, Supro USA will pay ground shipping both ways.
For amplifiers owned over 30 days and less than 365 days, (except extended warranty, which will be
extend coverage for 2 years), customer pays shipping to Supro USA and Supro USA pays return ground
shipping. If the amplifier is returned to Supro and the cause is proven to be oversight or user error,
customer will be responsible for return shipping.
For non-warranty service, the customer pays return shipping both ways. Repair charges must be paid
within 60 days of completion or it becomes the property of SuproUSA.
3.2 International Warranty:
(for customers outside of the United States and Canada)
Supro USA has chosen only the best dealers and distributors to work with.
1. Call the Supro dealer that you purchased your amplifier from. Inform them the nature of the
problem you are having. Most often they will be able to assist you with replacement parts or
service
2. If your dealer is unable to help, call the Authorized Supro Distributor in your country (you can
find their details on our site). They have the technical staff and experience to assist you, and
also have all of the resources of Supro engineers at their disposal
3. If you are still unable to get the assistance you require or you feel you have a problem that the
Distributor cannot resolve, contact us directly by sending an e-mail to [e-mail],
but only if you have tried both previous routes first.
11