Sur-gard Sg security communications dlm-4l User manual

Specifications

Features

• 4 image storage

• Camera supervision

• Compatible control panel: PC5015 v2.2 with PC5108L Interface

Module

Power

• 10.5 - 16.0VDC

• 180mA @ 12VDC

Video

• Output of 5108L

• Transmits one frame in approximately 10 to 12 seconds

Mounting the Panel

Thissystemshouldbeinstalledandservicedbyqualifiedsecurity

professionals.

IftheDLM-4Listobeusedwithasecuritysystem,installandtestthe

security system according to the manufacturer’s instructions. For

convenience,installtheDLM-4Lmoduleclosetothesecuritysystem's

controlpanel.

1.Removetheprintedcircuitboardandmountinghardwarefromthe

cardboard packaging. It is recommended that the DLM-4L be

mounted in its own cabinet with the 5108L.

2.Before attaching the cabinet to the wall, press the four nylon

mounting studs into the raised mounting holes from the back of

the cabinet.

3.Mount the cabinet securely to the wall. Use appropriate wall

anchors when securing the panel to drywall, plaster, concrete,

brick or other similar surfaces.

4.Press theDLM-4Lonto thefourmounting studs.

Power Requirements

The DLM-4L v1.0L is used with the PC5108L Video Switcher/Zone

Expansion Interface Module. Refer to the hook-up diagram below

for power connections.

TerminalConnections

Refer to the hook-up diagram below for terminal connections.

Video Connection

The video source for the DLM-4L is provided by the output of the

5108L. If another device such as a VCR or monitor is connected to

the output of the 5108L, then take the output of the device or T-tap

the video connection to provide the necessary video connection to

the DLM-4L.

All cameras should be installed prior to connection of the DLM-4L

and PC5108L. Correct installation, alignment and lens will provide

for maximum results on the Downlook system.

For more information regarding Downlook operation, programming

andtesting,seethePC5108LInstallationManual.

Dip Switch Settings

There are 8 dip switches that must be set in the OFF position.

DLM-4L Downlook Still-Frame Video

Transmission Module

Software Version 1.0L INSTALLATION INSTRUCTIONS

DLM-4L with PC5108L Hook-up Diagram

firealarmresources.com

LIMITED WARRANTY

Digital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product shall be free of defect in materials and workmanship under normal

use and that in fulfilment of any breach of such warranty, Digital Security Controls Ltd. shall, at its option, repair or replace the defective equipment upon return of the equipment

to its repair depot. This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control

of Digital Security Controls Ltd. such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper application of the

equipment.

Theforegoingwarrantyshallapplyonlytotheoriginalbuyer,andisandshallbeinlieuofanyandallotherwarranties,whetherexpressedorimpliedandofallotherobligationsorliabilities

on the part of Digital Security Controls Ltd. This warranty contains the entire warranty. Digital Security Controls Ltd. neither assumes, nor authorizes any other person purporting to

act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product.

In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential damages, loss of anticipated profits, loss of time or any other losses incurred by the

buyer in connection with the purchase, installation or operation or failure of this product.

WARNING: Digital Security Controls Ltd. recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited

to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected.

FCCCOMPLIANCE

CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Re-orient the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet

is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4

Important Information

This equipment complies with Part 68 of the FCC Rules. On the side of this equipment is a label that contains, among other information, the FCC registration

number of this equipment.

Notification to Telephone Company: Upon request, the customer shall notify the telephone company of the particular line to which the connection will

be made, and provide the FCC registration number and the ringer equivalence of the protective circuit.

FCC Registration Number: F53CAN-32103-DM-N Ringer Equivalence Number: 0.4B USOC Jack: RJ-11C

Facility Interface Code: N/A Service Order Code: N/A

Telephone Connection Requirements: Except for the telephone company provided ringers, all connections to the telephone network shall be made through

standard plugs and telephone company provided jacks, or equivalent, in such a manner as to allow for easy, immediate disconnection

of the terminal equipment. Standard jacks shall be so arranged that, if the plug connected thereto is withdrawn, no interference to the operation of the

equipment at the customer’s premises which remains connected to the telephone network shall occur by reason of such withdrawal.

Incidence of Harm: Should terminal equipment or protective circuitry cause harm to the telephone network, the telephone company shall, where

practicable, notify the customer that temporary disconnection of service may be required; however, where prior notice is not practicable, the telephone

company may temporarily discontinue service if such action is deemed reasonable in the circumstances. In the case of such temporary discontinuance,

the telephone company shall promptly notify the customer and will be given the opportunity to correct the situation.

Additional Telephone Company Information: The security control panel must be properly connected to the telephone line with a USOC RJ-31X telephone

jack. The FCC prohibits customer-provided terminal equipment be connected to party lines or to be used in conjunction with coin telephone service.

Interconnect rules may vary from state to state.

Changes in Telephone Company Equipment of Facilities: The telephone company may make changes in its communications facilities, equipment,

operations or procedures, where such actions are reasonably required and proper in its business. Should any such changes render the customer’s terminal

equipment incompatible with the telephone company facilities the customer shall be given adequate notice to the effect modifications to maintain

uninterrupted service.

Ringer Equivalence Number (REN): The REN is useful to determine the quantity of devices that you may connect to your telephone line and still have

all of those devices ring when your telephone number is called. In most, but not all areas, the sum of the RENs of all devices connected to one line should

not exceed five (5.0). To be certain of the number of devices that you may connect to your line, you may want to contact your local telephone company.

Equipment Maintenance Facility: If you experience trouble with this telephone equipment, please contact the facility indicated below for information

on obtaining service or repairs. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected

or until you are sure that the equipment is not malfunctioning.

Digital Security Controls Ltd., 160 Washburn Street, Lockport, NY 14094