Sure Electronics Mini Square Camera User manual
EX-SDI / HD-SDI / CVBS
Mini Square Camera
OPERATION MANUAL
Thank you for choosing our high quality camera. Before attempting to connect
operate this unit,please read and follow these instructions.
M365-HMS8130-001 CONTENTS
1. NOTICES
2. FOR YOUR SAFETY
3. FEATURES
4. COMPONENTS
5. DIMENSIONS
6. CAMERA MOUNTING POSITION
7. CONNECTION
8. SPECIFICATION
9. OSD MENU STRUCTURE
10. HIDDEN MENU
These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not per form any servicing other than
that contained in the operating instructions unless you are qualied to do so.
Use Class 2 Power Supply Only
CAUTION
1. NOTICES
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Note -
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Caution -
Any changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
1. A regulated DC12V 300mA power supply is recommended for use with this
camera to ensure the best picture quality and stable operation.
An unregulated power supply may cause damage to the camera.
Using an unregulated power supply will void the product warranty.
2. It is recommended that the camera is used with a monitor that has a CCTV
quality 75 video impedance level.
If your monitor is switched to high impedance, then please adjust accordingly.
3. Do not attempt to disassemble the camera to access internal components.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which
may cause smear on the picture and possible damage to the image sensor.
5. Do not remove the serial sticker for the warranty service.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product or their local government oce for details of where and how to safely
recycle the item.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER(OR BACK).
NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFED SERVICE
PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sucient mangnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.
2. FOR YOUR SAFETY
1) All warnings and instructions in this manual should be followed.
2) Save this manual for future reference.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) To help prevent electric shock, plug the equipment and peripheral power cables
into properly polarized or grounded electrical outlets. These cables are
equipped with the wide blade or the third prong to ensure proper grounding.
Do not use adapter plugs or remove the grounding prong from a cable. If the
provided plug does not t your outlet, consult an electrician.
10) Ensure that nothing rests on your equipment’s cables and that the cables are
not located where they can be stepped on, tripped over, or pinched.
11) Only use attachments or accessories as specied.
12) Only use the equipment with the cart, stand, tripod, bracket,
or table that is specied by the manufacturer or sold with the
apparatus. When a cart is used, use caution to prevent the cart
from tipping over and to avoid injury.
13) Do not connect or disconnect during lightning storms due to risk of electric shock.
14) If any of the following conditions occur, unplug the equipment from the
electrical outlet and replace the part or contact your trained service provider:
• The power cable, extension cable, or plug is damaged.
• An object has fallen into the equipment.
• The equipment has been exposed to water.
• The equipment has been dropped or damaged.
• The equipment does not operate correctly when you follow the operating
instructions.
3. FEATURES
• High resolution
1/2.8” SONY EXMOR R Progressive Scan CMOS
• Support various digital video output
1080p@30fps / 1080p@25fps / 720p@60fps / 720p@50fps / 720p@30fps / 720p@25fps
• EX-SDI (1.0_2.0_2.1) / HD-SDI Output is suitable for long reach transmission over
single coaxial cable.
Transmission Distance
HD-SDI : COLOR 150m (5C-HFBT)
EX-SDI 1.0 : COLOR 300m (5C-HFBT), EX-SDI 2.0 / 2.1 : COLOR 500m (5C-HFBT(A))
• True WDR (Wide Dynamic Range)
• Digital Zoom
• DSS (Digital Slow Shutter)
• HLC
• Motion Detection
• Privacy masking 16 zones
• RS-485
• 3DNR
• Option : Cable Joystick (OSD)
• Multi Language OSD menu
(ENGLISH / JAPANESE / RUSSIAN / SPANISH / GERMAN /FRANCE/ PORTUGUESE /
KOREAN)
4. COMPONENTS 5. DIMENSIONS
Unit(mm)
31
31
30
30
18.1
30
30
14
EX-SDI / HD-SDI
CONNECTOR
EX-SDI / HD-SDI
CONNECTOR
Square Camera
Mounting
Bracket
Screw 4ea M2 x 2.5
Tapping
3 x 8.0
Operation
Manual
DIY cable
EX-SDI / HD-SDI / CVBS
Mini Square Camera
OPERATION MANUAL
Thank you for choosing our high quality camera. Before attempting to connect
operate this unit,please read and follow these instructions.
M365-HMS8130-001 CONTENTS
1. NOTICES
2. FOR YOUR SAFETY
3. FEATURES
4. COMPONENTS
5. DIMENSIONS
6. CAMERA MOUNTING POSITION
7. CONNECTION
8. SPECIFICATION
9. OSD MENU STRUCTURE
10. HIDDEN MENU
These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualied to do so.
Use Class 2 Power Supply Only
CAUTION
1. NOTICES
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Note -
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Caution -
Any changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
1. A regulated DC12V 300mA power supply is recommended for use with this
camera to ensure the best picture quality and stable operation.
An unregulated power supply may cause damage to the camera.
Using an unregulated power supply will void the product warranty.
2. It is recommended that the camera is used with a monitor that has a CCTV
quality 75 video impedance level.
If your monitor is switched to high impedance, then please adjust accordingly.
3. Do not attempt to disassemble the camera to access internal components.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which
may cause smear on the picture and possible damage to the image sensor.
5. Do not remove the serial sticker for the warranty service.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product or their local government oce for details of where and how to safely
recycle the item.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER(OR BACK).
NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFED SERVICE
PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sucient mangnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.
2. FOR YOUR SAFETY
1) All warnings and instructions in this manual should be followed.
2) Save this manual for future reference.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) To help prevent electric shock, plug the equipment and peripheral power cables
into properly polarized or grounded electrical outlets. These cables are
equipped with the wide blade or the third prong to ensure proper grounding.
Do not use adapter plugs or remove the grounding prong from a cable. If the
provided plug does not t your outlet, consult an electrician.
10) Ensure that nothing rests on your equipment’s cables and that the cables are
not located where they can be stepped on, tripped over, or pinched.
11) Only use attachments or accessories as specied.
12) Only use the equipment with the cart, stand, tripod, bracket,
or table that is specied by the manufacturer or sold with the
apparatus. When a cart is used, use caution to prevent the cart
from tipping over and to avoid injury.
13) Do not connect or disconnect during lightning storms due to risk of electric shock.
14) If any of the following conditions occur, unplug the equipment from the
electrical outlet and replace the part or contact your trained service provider:
• The power cable, extension cable, or plug is damaged.
• An object has fallen into the equipment.
• The equipment has been exposed to water.
• The equipment has been dropped or damaged.
• The equipment does not operate correctly when you follow the operating
instructions.
3. FEATURES
• High resolution
1/2.8” SONY EXMOR R Progressive Scan CMOS
• Support various digital video output
1080p@30fps / 1080p@25fps / 720p@60fps / 720p@50fps / 720p@30fps / 720p@25fps
• EX-SDI (1.0_2.0_2.1) / HD-SDI Output is suitable for long reach transmission over
single coaxial cable.
Transmission Distance
HD-SDI : COLOR 150m (5C-HFBT)
EX-SDI 1.0 : COLOR 300m (5C-HFBT), EX-SDI 2.0 / 2.1 : COLOR 500m (5C-HFBT(A))
• True WDR (Wide Dynamic Range)
• Digital Zoom
• DSS (Digital Slow Shutter)
• HLC
• Motion Detection
• Privacy masking 16 zones
• RS-485
• 3DNR
• Option : Cable Joystick (OSD)
• Multi Language OSD menu
(ENGLISH / JAPANESE / RUSSIAN / SPANISH / GERMAN /FRANCE/ PORTUGUESE /
KOREAN)
4. COMPONENTS 5. DIMENSIONS
Unit(mm)
31
31
30
30
18.1
30
30
14
EX-SDI / HD-SDI
CONNECTOR
EX-SDI / HD-SDI
CONNECTOR
Square Camera
Mounting
Bracket
Screw 4ea M2 x 2.5
Tapping
3 x 8.0
Operation
Manual
DIY cable
EX-SDI / HD-SDI / CVBS
Mini Square Camera
OPERATION MANUAL
Thank you for choosing our high quality camera. Before attempting to connect
operate this unit,please read and follow these instructions.
M365-HMS8130-001 CONTENTS
1. NOTICES
2. FOR YOUR SAFETY
3. FEATURES
4. COMPONENTS
5. DIMENSIONS
6. CAMERA MOUNTING POSITION
7. CONNECTION
8. SPECIFICATION
9. OSD MENU STRUCTURE
10. HIDDEN MENU
These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not per form any servicing other than
that contained in the operating instructions unless you are qualied to do so.
Use Class 2 Power Supply Only
CAUTION
1. NOTICES
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Note -
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Caution -
Any changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
1. A regulated DC12V 300mA power supply is recommended for use with this
camera to ensure the best picture quality and stable operation.
An unregulated power supply may cause damage to the camera.
Using an unregulated power supply will void the product warranty.
2. It is recommended that the camera is used with a monitor that has a CCTV
quality 75 video impedance level.
If your monitor is switched to high impedance, then please adjust accordingly.
3. Do not attempt to disassemble the camera to access internal components.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which
may cause smear on the picture and possible damage to the image sensor.
5. Do not remove the serial sticker for the warranty service.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product or their local government oce for details of where and how to safely
recycle the item.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER(OR BACK).
NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFED SERVICE
PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sucient mangnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.
2. FOR YOUR SAFETY
1) All warnings and instructions in this manual should be followed.
2) Save this manual for future reference.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) To help prevent electric shock, plug the equipment and peripheral power cables
into properly polarized or grounded electrical outlets. These cables are
equipped with the wide blade or the third prong to ensure proper grounding.
Do not use adapter plugs or remove the grounding prong from a cable. If the
provided plug does not t your outlet, consult an electrician.
10) Ensure that nothing rests on your equipment’s cables and that the cables are
not located where they can be stepped on, tripped over, or pinched.
11) Only use attachments or accessories as specied.
12) Only use the equipment with the cart, stand, tripod, bracket,
or table that is specied by the manufacturer or sold with the
apparatus. When a cart is used, use caution to prevent the cart
from tipping over and to avoid injury.
13) Do not connect or disconnect during lightning storms due to risk of electric shock.
14) If any of the following conditions occur, unplug the equipment from the
electrical outlet and replace the part or contact your trained service provider:
• The power cable, extension cable, or plug is damaged.
• An object has fallen into the equipment.
• The equipment has been exposed to water.
• The equipment has been dropped or damaged.
• The equipment does not operate correctly when you follow the operating
instructions.
3. FEATURES
• High resolution
1/2.8” SONY EXMOR R Progressive Scan CMOS
• Support various digital video output
1080p@30fps / 1080p@25fps / 720p@60fps / 720p@50fps / 720p@30fps / 720p@25fps
• EX-SDI (1.0_2.0_2.1) / HD-SDI Output is suitable for long reach transmission over
single coaxial cable.
Transmission Distance
HD-SDI : COLOR 150m (5C-HFBT)
EX-SDI 1.0 : COLOR 300m (5C-HFBT), EX-SDI 2.0 / 2.1 : COLOR 500m (5C-HFBT(A))
• True WDR (Wide Dynamic Range)
• Digital Zoom
• DSS (Digital Slow Shutter)
• HLC
• Motion Detection
• Privacy masking 16 zones
• RS-485
• 3DNR
• Option : Cable Joystick (OSD)
• Multi Language OSD menu
(ENGLISH / JAPANESE / RUSSIAN / SPANISH / GERMAN /FRANCE/ PORTUGUESE /
KOREAN)
4. COMPONENTS 5. DIMENSIONS
Unit(mm)
31
31
30
30
18.1
30
30
14
EX-SDI / HD-SDI
CONNECTOR
EX-SDI / HD-SDI
CONNECTOR
Square Camera
Mounting
Bracket
Screw 4ea M2 x 2.5
Tapping
3 x 8.0
Operation
Manual
DIY cable
EX-SDI / HD-SDI / CVBS
Mini Square Camera
OPERATION MANUAL
Thank you for choosing our high quality camera. Before attempting to connect
operate this unit,please read and follow these instructions.
M365-HMS8130-001 CONTENTS
1. NOTICES
2. FOR YOUR SAFETY
3. FEATURES
4. COMPONENTS
5. DIMENSIONS
6. CAMERA MOUNTING POSITION
7. CONNECTION
8. SPECIFICATION
9. OSD MENU STRUCTURE
10. HIDDEN MENU
These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not per form any servicing other than
that contained in the operating instructions unless you are qualied to do so.
Use Class 2 Power Supply Only
CAUTION
1. NOTICES
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Note -
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Caution -
Any changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
1. A regulated DC12V 300mA power supply is recommended for use with this
camera to ensure the best picture quality and stable operation.
An unregulated power supply may cause damage to the camera.
Using an unregulated power supply will void the product warranty.
2. It is recommended that the camera is used with a monitor that has a CCTV
quality 75 video impedance level.
If your monitor is switched to high impedance, then please adjust accordingly.
3. Do not attempt to disassemble the camera to access internal components.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which
may cause smear on the picture and possible damage to the image sensor.
5. Do not remove the serial sticker for the warranty service.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product or their local government oce for details of where and how to safely
recycle the item.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER(OR BACK).
NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFED SERVICE
PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sucient mangnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.
2. FOR YOUR SAFETY
1) All warnings and instructions in this manual should be followed.
2) Save this manual for future reference.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) To help prevent electric shock, plug the equipment and peripheral power cables
into properly polarized or grounded electrical outlets. These cables are
equipped with the wide blade or the third prong to ensure proper grounding.
Do not use adapter plugs or remove the grounding prong from a cable. If the
provided plug does not t your outlet, consult an electrician.
10) Ensure that nothing rests on your equipment’s cables and that the cables are
not located where they can be stepped on, tripped over, or pinched.
11) Only use attachments or accessories as specied.
12) Only use the equipment with the cart, stand, tripod, bracket,
or table that is specied by the manufacturer or sold with the
apparatus. When a cart is used, use caution to prevent the cart
from tipping over and to avoid injury.
13) Do not connect or disconnect during lightning storms due to risk of electric shock.
14) If any of the following conditions occur, unplug the equipment from the
electrical outlet and replace the part or contact your trained service provider:
• The power cable, extension cable, or plug is damaged.
• An object has fallen into the equipment.
• The equipment has been exposed to water.
• The equipment has been dropped or damaged.
• The equipment does not operate correctly when you follow the operating
instructions.
3. FEATURES
• High resolution
1/2.8” SONY EXMOR R Progressive Scan CMOS
• Support various digital video output
1080p@30fps / 1080p@25fps / 720p@60fps / 720p@50fps / 720p@30fps / 720p@25fps
• EX-SDI (1.0_2.0_2.1) / HD-SDI Output is suitable for long reach transmission over
single coaxial cable.
Transmission Distance
HD-SDI : COLOR 150m (5C-HFBT)
EX-SDI 1.0 : COLOR 300m (5C-HFBT), EX-SDI 2.0 / 2.1 : COLOR 500m (5C-HFBT(A))
• True WDR (Wide Dynamic Range)
• Digital Zoom
• DSS (Digital Slow Shutter)
• HLC
• Motion Detection
• Privacy masking 16 zones
• RS-485
• 3DNR
• Option : Cable Joystick (OSD)
• Multi Language OSD menu
(ENGLISH / JAPANESE / RUSSIAN / SPANISH / GERMAN /FRANCE/ PORTUGUESE /
KOREAN)
4. COMPONENTS 5. DIMENSIONS
Unit(mm)
31
31
30
30
18.1
30
30
14
EX-SDI / HD-SDI
CONNECTOR
EX-SDI / HD-SDI
CONNECTOR
Square Camera
Mounting
Bracket
Screw 4ea M2 x 2.5
Tapping
3 x 8.0
Operation
Manual
DIY cable
EX-SDI / HD-SDI / CVBS
Mini Square Camera
OPERATION MANUAL
Thank you for choosing our high quality camera. Before attempting to connect
operate this unit,please read and follow these instructions.
M365-HMS8130-001 CONTENTS
1. NOTICES
2. FOR YOUR SAFETY
3. FEATURES
4. COMPONENTS
5. DIMENSIONS
6. CAMERA MOUNTING POSITION
7. CONNECTION
8. SPECIFICATION
9. OSD MENU STRUCTURE
10. HIDDEN MENU
These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualied to do so.
Use Class 2 Power Supply Only
CAUTION
1. NOTICES
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Note -
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Caution -
Any changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
1. A regulated DC12V 300mA power supply is recommended for use with this
camera to ensure the best picture quality and stable operation.
An unregulated power supply may cause damage to the camera.
Using an unregulated power supply will void the product warranty.
2. It is recommended that the camera is used with a monitor that has a CCTV
quality 75 video impedance level.
If your monitor is switched to high impedance, then please adjust accordingly.
3. Do not attempt to disassemble the camera to access internal components.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which
may cause smear on the picture and possible damage to the image sensor.
5. Do not remove the serial sticker for the warranty service.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product or their local government oce for details of where and how to safely
recycle the item.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER(OR BACK).
NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFED SERVICE
PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sucient mangnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.
2. FOR YOUR SAFETY
1) All warnings and instructions in this manual should be followed.
2) Save this manual for future reference.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) To help prevent electric shock, plug the equipment and peripheral power cables
into properly polarized or grounded electrical outlets. These cables are
equipped with the wide blade or the third prong to ensure proper grounding.
Do not use adapter plugs or remove the grounding prong from a cable. If the
provided plug does not t your outlet, consult an electrician.
10) Ensure that nothing rests on your equipment’s cables and that the cables are
not located where they can be stepped on, tripped over, or pinched.
11) Only use attachments or accessories as specied.
12) Only use the equipment with the cart, stand, tripod, bracket,
or table that is specied by the manufacturer or sold with the
apparatus. When a cart is used, use caution to prevent the cart
from tipping over and to avoid injury.
13) Do not connect or disconnect during lightning storms due to risk of electric shock.
14) If any of the following conditions occur, unplug the equipment from the
electrical outlet and replace the part or contact your trained service provider:
• The power cable, extension cable, or plug is damaged.
• An object has fallen into the equipment.
• The equipment has been exposed to water.
• The equipment has been dropped or damaged.
• The equipment does not operate correctly when you follow the operating
instructions.
3. FEATURES
• High resolution
1/2.8” SONY EXMOR R Progressive Scan CMOS
• Support various digital video output
1080p@30fps / 1080p@25fps / 720p@60fps / 720p@50fps / 720p@30fps / 720p@25fps
• EX-SDI (1.0_2.0_2.1) / HD-SDI Output is suitable for long reach transmission over
single coaxial cable.
Transmission Distance
HD-SDI : COLOR 150m (5C-HFBT)
EX-SDI 1.0 : COLOR 300m (5C-HFBT), EX-SDI 2.0 / 2.1 : COLOR 500m (5C-HFBT(A))
• True WDR (Wide Dynamic Range)
• Digital Zoom
• DSS (Digital Slow Shutter)
• HLC
• Motion Detection
• Privacy masking 16 zones
• RS-485
• 3DNR
• Option : Cable Joystick (OSD)
• Multi Language OSD menu
(ENGLISH / JAPANESE / RUSSIAN / SPANISH / GERMAN /FRANCE/ PORTUGUESE /
KOREAN)
4. COMPONENTS 5. DIMENSIONS
Unit(mm)
31
31
30
30
18.1
30
30
14
EX-SDI / HD-SDI
CONNECTOR
EX-SDI / HD-SDI
CONNECTOR
Square Camera
Mounting
Bracket
Screw 4ea M2 x 2.5
Tapping
3 x 8.0
Operation
Manual
DIY cable
EX-SDI / HD-SDI / CVBS
Mini Square Camera
OPERATION MANUAL
Thank you for choosing our high quality camera. Before attempting to connect
operate this unit,please read and follow these instructions.
M365-HMS8130-001 CONTENTS
1. NOTICES
2. FOR YOUR SAFETY
3. FEATURES
4. COMPONENTS
5. DIMENSIONS
6. CAMERA MOUNTING POSITION
7. CONNECTION
8. SPECIFICATION
9. OSD MENU STRUCTURE
10. HIDDEN MENU
These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualied to do so.
Use Class 2 Power Supply Only
CAUTION
1. NOTICES
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Note -
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Caution -
Any changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
1. A regulated DC12V 300mA power supply is recommended for use with this
camera to ensure the best picture quality and stable operation.
An unregulated power supply may cause damage to the camera.
Using an unregulated power supply will void the product warranty.
2. It is recommended that the camera is used with a monitor that has a CCTV
quality 75 video impedance level.
If your monitor is switched to high impedance, then please adjust accordingly.
3. Do not attempt to disassemble the camera to access internal components.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which
may cause smear on the picture and possible damage to the image sensor.
5. Do not remove the serial sticker for the warranty service.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product or their local government oce for details of where and how to safely
recycle the item.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER(OR BACK).
NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFED SERVICE
PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sucient mangnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.
2. FOR YOUR SAFETY
1) All warnings and instructions in this manual should be followed.
2) Save this manual for future reference.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) To help prevent electric shock, plug the equipment and peripheral power cables
into properly polarized or grounded electrical outlets. These cables are
equipped with the wide blade or the third prong to ensure proper grounding.
Do not use adapter plugs or remove the grounding prong from a cable. If the
provided plug does not t your outlet, consult an electrician.
10) Ensure that nothing rests on your equipment’s cables and that the cables are
not located where they can be stepped on, tripped over, or pinched.
11) Only use attachments or accessories as specied.
12) Only use the equipment with the cart, stand, tripod, bracket,
or table that is specied by the manufacturer or sold with the
apparatus. When a cart is used, use caution to prevent the cart
from tipping over and to avoid injury.
13) Do not connect or disconnect during lightning storms due to risk of electric shock.
14) If any of the following conditions occur, unplug the equipment from the
electrical outlet and replace the part or contact your trained service provider:
• The power cable, extension cable, or plug is damaged.
• An object has fallen into the equipment.
• The equipment has been exposed to water.
• The equipment has been dropped or damaged.
• The equipment does not operate correctly when you follow the operating
instructions.
3. FEATURES
• High resolution
1/2.8” SONY EXMOR R Progressive Scan CMOS
• Support various digital video output
1080p@30fps / 1080p@25fps / 720p@60fps / 720p@50fps / 720p@30fps / 720p@25fps
• EX-SDI (1.0_2.0_2.1) / HD-SDI Output is suitable for long reach transmission over
single coaxial cable.
Transmission Distance
HD-SDI : COLOR 150m (5C-HFBT)
EX-SDI 1.0 : COLOR 300m (5C-HFBT), EX-SDI 2.0 / 2.1 : COLOR 500m (5C-HFBT(A))
• True WDR (Wide Dynamic Range)
• Digital Zoom
• DSS (Digital Slow Shutter)
• HLC
• Motion Detection
• Privacy masking 16 zones
• RS-485
• 3DNR
• Option : Cable Joystick (OSD)
• Multi Language OSD menu
(ENGLISH / JAPANESE / RUSSIAN / SPANISH / GERMAN /FRANCE/ PORTUGUESE /
KOREAN)
4. COMPONENTS 5. DIMENSIONS
Unit(mm)
31
31
30
30
18.1
30
30
14
EX-SDI / HD-SDI
CONNECTOR
EX-SDI / HD-SDI
CONNECTOR
Square Camera
Mounting
Bracket
Screw 4ea M2 x 2.5
Tapping
3 x 8.0
Operation
Manual
DIY cable
EX-SDI / HD-SDI / CVBS
Mini Square Camera
OPERATION MANUAL
Thank you for choosing our high quality camera. Before attempting to connect
operate this unit,please read and follow these instructions.
M365-HMS8130-001 CONTENTS
1. NOTICES
2. FOR YOUR SAFETY
3. FEATURES
4. COMPONENTS
5. DIMENSIONS
6. CAMERA MOUNTING POSITION
7. CONNECTION
8. SPECIFICATION
9. OSD MENU STRUCTURE
10. HIDDEN MENU
These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not per form any servicing other than
that contained in the operating instructions unless you are qualied to do so.
Use Class 2 Power Supply Only
CAUTION
1. NOTICES
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Note -
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Caution -
Any changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
1. A regulated DC12V 300mA power supply is recommended for use with this
camera to ensure the best picture quality and stable operation.
An unregulated power supply may cause damage to the camera.
Using an unregulated power supply will void the product warranty.
2. It is recommended that the camera is used with a monitor that has a CCTV
quality 75 video impedance level.
If your monitor is switched to high impedance, then please adjust accordingly.
3. Do not attempt to disassemble the camera to access internal components.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which
may cause smear on the picture and possible damage to the image sensor.
5. Do not remove the serial sticker for the warranty service.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product or their local government oce for details of where and how to safely
recycle the item.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER(OR BACK).
NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFED SERVICE
PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sucient mangnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.
2. FOR YOUR SAFETY
1) All warnings and instructions in this manual should be followed.
2) Save this manual for future reference.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) To help prevent electric shock, plug the equipment and peripheral power cables
into properly polarized or grounded electrical outlets. These cables are
equipped with the wide blade or the third prong to ensure proper grounding.
Do not use adapter plugs or remove the grounding prong from a cable. If the
provided plug does not t your outlet, consult an electrician.
10) Ensure that nothing rests on your equipment’s cables and that the cables are
not located where they can be stepped on, tripped over, or pinched.
11) Only use attachments or accessories as specied.
12) Only use the equipment with the cart, stand, tripod, bracket,
or table that is specied by the manufacturer or sold with the
apparatus. When a cart is used, use caution to prevent the cart
from tipping over and to avoid injury.
13) Do not connect or disconnect during lightning storms due to risk of electric shock.
14) If any of the following conditions occur, unplug the equipment from the
electrical outlet and replace the part or contact your trained service provider:
• The power cable, extension cable, or plug is damaged.
• An object has fallen into the equipment.
• The equipment has been exposed to water.
• The equipment has been dropped or damaged.
• The equipment does not operate correctly when you follow the operating
instructions.
3. FEATURES
• High resolution
1/2.8” SONY EXMOR R Progressive Scan CMOS
• Support various digital video output
1080p@30fps / 1080p@25fps / 720p@60fps / 720p@50fps / 720p@30fps / 720p@25fps
• EX-SDI (1.0_2.0_2.1) / HD-SDI Output is suitable for long reach transmission over
single coaxial cable.
Transmission Distance
HD-SDI : COLOR 150m (5C-HFBT)
EX-SDI 1.0 : COLOR 300m (5C-HFBT), EX-SDI 2.0 / 2.1 : COLOR 500m (5C-HFBT(A))
• True WDR (Wide Dynamic Range)
• Digital Zoom
• DSS (Digital Slow Shutter)
• HLC
• Motion Detection
• Privacy masking 16 zones
• RS-485
• 3DNR
• Option : Cable Joystick (OSD)
• Multi Language OSD menu
(ENGLISH / JAPANESE / RUSSIAN / SPANISH / GERMAN /FRANCE/ PORTUGUESE /
KOREAN)
4. COMPONENTS 5. DIMENSIONS
Unit(mm)
31
31
30
30
18.1
30
30
14
EX-SDI / HD-SDI
CONNECTOR
EX-SDI / HD-SDI
CONNECTOR
Square Camera
Mounting
Bracket
Screw 4ea M2 x 2.5
Tapping
3 x 8.0
Operation
Manual
DIY cable
6. CAMERA MOUNTING POSITION 7. CONNECTION 8. SPECIFICATION
9. OSD MENU STRUCTURE
• Menu structure
10. HIDDEN MENU
• CONVERT SDI OUTPUT MODE
STEP 1. ENTER
RS485 : Press [LEFT] → [LEFT] → [RIGHT] →[RIGHT] key.
AD-KEY : Press UP/DOWN/LEFT/RIGHT key 3 times.
SETP 2. SELECT
Press UP key 5 times : EX-SDI 2.1
Press DOWN key 5 times : EX-SDI 2.0
Press LEFT key 5 times : HD-SDI
Press RIGHT key 5 times : EX-SDI 1.0
STEP 3. CONFIRM
If the 'YES' is not checked within 30sec, the value returns to the previous setting.
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
LENS
LENS TYPE ELC
LENS MODE NORMAL/DEBLUR
RETURN
EXPOSURE
BRIGHTNESS 0~20
SHUTTER MODE AUTO/MANUAL/
FLICKER
SHUTTER SPEED 1/30(25),1/60(50),1/120(100),1/250,1/500,1/1000,1/2000,1/4
000,1/8000,1/16000,1/30000
DSS OFF/X2/X4/X8/X16/
X32
AGC MAX OFF,3dB~45dB
INITIAL
RETURN
WHITE BALANCE
WB MODE AUTO/AUTO EXT/PUSH LOCK/MANUAL
PUSH AUTO [ ]
COLOR GAIN 0~20
KELVIN LOW/MIDDLE/HIGH
RED GAIN 0~20
BLUE GAIN 0~20
INITIAL
RETURN
WDR/BLC
MODE OFF/BLC/HLC/WDR
LEVEL 0~20
X-POSITION 0~20
Y-POSITION 0~20
X-SIZE 0~20
Y-SIZE 0~20
COLOR BLACK/WHITE/YELLOW/CYAN/GREEN/MAGENTA/RED/BLUE
INITIAL
RETURN
DAY&NIGHT
MODE AUTO/DAY(COLOR)/NIGHT(BW)
DWLL TIME 0~20 sec
D>N THRES 1~35
N>D THRES 0~34
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
IMAGE
SHARPNESS 0~10
GAMMA 0.45/0.50/0.55/0.6
0/0.65/0.70/0.75
FLIP OFF/H-FLIP/
V-FLIP/HV-FLIP
D-WDR OFF/ON
DNR OFF/LOW/MIDDLE/
HIGH
DZOOM x1.0 ~ x16
DEFOG OFF/ON
MODE AUTO/MANUAL
LEVEL LOW/MIDDLE/HIGH
RETURN
INITIAL
RETURN
SPECIAL
CAM TITLE OFF/ON
EDIT PANEL
POSITION [POSITION EDIT]
RETURN
PRIVACY OFF/ON
ZONE NO 0~15
MASK MODE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
COLOR
WHITE/YELLOW/
CYAN/GREEN/
MAGENTA/RED/
BLUE
TRANSPARENCY 0%/33%/66%/100%
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
SPECIAL
MOTION OFF/ON
ZONE NO 0~3
WINDOW USE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
SENSITIVITY 0~10
ALAM MODE OSD/TEXT
INITIAL
RETURN
SYSTEM
FREMARATE 1080p30/1080p25/720p60/720p50/720p
30/720p25
SDI OUT HD-SDI/EX-SD 1.0/ EX-SD 2.0/ EX-SD 2.1
ANALOG OUT CVBS
APPLY YES
LANGUAGE English / Japanese / Russian / Spanish
/ German /France/ Portuguese / Korean
RETURN
INITIAL
RETURN
FACTORY DEF
EXIT
Mounting
bracket
Camera
M2 x 2.5
❶
Tapping
3 x 8.0 ❷
❶
CAUTION !
Please start installing
in the order shown.
Image Sensor 1/2.8” SONY EXMOR R Progressive Scan CMOS
Eective Pixels 1945(H) x 1097(V)
Unit cell size (um) 2.9(H) x 2.9(V)
Video Output EX-SDI/HD-SDI: 1080p@25(30)fps/720p@50(60)fps/720p25(30)fps
TV out: CVBS NTSC / PAL (720H)
Transmission
Distance
HD-SDI: Color 150m(5C-HFBT)
EX-SDI1.0: Color 300m(5C-HFBT)
EX-SDI 2.0_2.1 Color 500m(5C-HFBT
(A)
)
Minimum
Illumination 0.2 Lux (F2.0, AGC:33dB, DSS:x2)
Shutter speed 1/30(25)s ~ 1/30,000s
Day/Night AUTO, COLOR, BW
Back/High Light
Compensation OFF / BLC / HLC / WDR selectable
Motion Detection OFF / ON
Privacy Masking 16 selectable zones
White Balance AUTO / AUTO EXT / PUSH LOCK / MANUAL
Functions FLIP(OFF, H, V, H/V), 3DNR, DEFOG, DSS, Digital Zoom, RS-485
Lens Fixed Board / Pinhole Lens
Operating
Temperature -10℃ ~ +50℃ (14℉ ~ 122℉)
Storage
Temperature -20℃ ~ +60℃ (-4℉ ~ 140℉)
Humidity Less than 80%
Power
Consumption 12VDC(±10%), Max.150mA
Dimension(mm) 30mm X 30mm
Weight Approx. 28.9g (Board lens)
• Design and specication are subject to change without notice.
• Basic specication
• Option specication
12V REGULATED
POWER SUPPLY
CVBS
RS485
EX-SDI
HD-SDI
BNC COLOR - YELLOW
White (RS485-)
Orange (RS485+)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
White(RS485-)
Black(RS485+)
↓
_ _ _ _ _ _ _ _ _ _ _ _ _
ABCDEFGHIJKLMN
OPQRSTUVWXYZ!?
0123456789~()^
SP> <BK
1. Communication Specification
RS-485
RateBaud Default 9600bps
Data bits 8 bits
Stop bits 1 bits
CAM ID Default "1"
Parity Check None
Supported Protocol PELCO-D, PELCO-P
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is an XOR sum of Byte1 ~ Byte7
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
• PELCO-D
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7
UP KEY 0 x FF Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F ChkSum
DOWN KEY 0 x FF Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F ChkSum
LEFT KEY 0 x FF Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 ChkSum
RIGHT KEY 0 x FF Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 ChkSum
MENU ENTER
KEY 0 x FF Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F ChkSum
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7 BYTE 8
UP KEY 0 x A0 Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F 0 x AF ChkSum
DOWN KEY 0 x A0 Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F 0 x AF ChkSum
LEFT KEY 0 x A0 Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 0 x AF ChkSum
RIGHT KEY 0 x A0 Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 0 x AF ChkSum
MENU ENTER
KEY 0 x A0 Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F 0 x AF ChkSum
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is the 8 bit (modulo 256) sum of the payload bytes
(Byte2 ~ Byte6) in the Command.
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
2. PELCO protocol for OSD remote control
• PELCO-P
12V REGULATED
POWER SUPPLY
CVBS
EX-SDI
HD-SDI
JOYSTICK
BNC COLOR - YELLOW
White (AD-KEY)
Black (GND)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
6. CAMERA MOUNTING POSITION 7. CONNECTION 8. SPECIFICATION
9. OSD MENU STRUCTURE
• Menu structure
10. HIDDEN MENU
• CONVERT SDI OUTPUT MODE
STEP 1. ENTER
RS485 : Press [LEFT] → [LEFT] → [RIGHT] →[RIGHT] key.
AD-KEY : Press UP/DOWN/LEFT/RIGHT key 3 times.
SETP 2. SELECT
Press UP key 5 times : EX-SDI 2.1
Press DOWN key 5 times : EX-SDI 2.0
Press LEFT key 5 times : HD-SDI
Press RIGHT key 5 times : EX-SDI 1.0
STEP 3. CONFIRM
If the 'YES' is not checked within 30sec, the value returns to the previous setting.
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
LENS
LENS TYPE ELC
LENS MODE NORMAL/DEBLUR
RETURN
EXPOSURE
BRIGHTNESS 0~20
SHUTTER MODE AUTO/MANUAL/
FLICKER
SHUTTER SPEED 1/30(25),1/60(50),1/120(100),1/250,1/500,1/1000,1/2000,1/4
000,1/8000,1/16000,1/30000
DSS OFF/X2/X4/X8/X16/
X32
AGC MAX OFF,3dB~45dB
INITIAL
RETURN
WHITE BALANCE
WB MODE AUTO/AUTO EXT/PUSH LOCK/MANUAL
PUSH AUTO [ ]
COLOR GAIN 0~20
KELVIN LOW/MIDDLE/HIGH
RED GAIN 0~20
BLUE GAIN 0~20
INITIAL
RETURN
WDR/BLC
MODE OFF/BLC/HLC/WDR
LEVEL 0~20
X-POSITION 0~20
Y-POSITION 0~20
X-SIZE 0~20
Y-SIZE 0~20
COLOR BLACK/WHITE/YELLOW/CYAN/GREEN/MAGENTA/RED/BLUE
INITIAL
RETURN
DAY&NIGHT
MODE AUTO/DAY(COLOR)/NIGHT(BW)
DWLL TIME 0~20 sec
D>N THRES 1~35
N>D THRES 0~34
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
IMAGE
SHARPNESS 0~10
GAMMA 0.45/0.50/0.55/0.6
0/0.65/0.70/0.75
FLIP OFF/H-FLIP/
V-FLIP/HV-FLIP
D-WDR OFF/ON
DNR OFF/LOW/MIDDLE/
HIGH
DZOOM x1.0 ~ x16
DEFOG OFF/ON
MODE AUTO/MANUAL
LEVEL LOW/MIDDLE/HIGH
RETURN
INITIAL
RETURN
SPECIAL
CAM TITLE OFF/ON
EDIT PANEL
POSITION [POSITION EDIT]
RETURN
PRIVACY OFF/ON
ZONE NO 0~15
MASK MODE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
COLOR
WHITE/YELLOW/
CYAN/GREEN/
MAGENTA/RED/
BLUE
TRANSPARENCY 0%/33%/66%/100%
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
SPECIAL
MOTION OFF/ON
ZONE NO 0~3
WINDOW USE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
SENSITIVITY 0~10
ALAM MODE OSD/TEXT
INITIAL
RETURN
SYSTEM
FREMARATE 1080p30/1080p25/720p60/720p50/720p
30/720p25
SDI OUT HD-SDI/EX-SD 1.0/ EX-SD 2.0/ EX-SD 2.1
ANALOG OUT CVBS
APPLY YES
LANGUAGE English / Japanese / Russian / Spanish
/ German /France/ Portuguese / Korean
RETURN
INITIAL
RETURN
FACTORY DEF
EXIT
Mounting
bracket
Camera
M2 x 2.5
❶
Tapping
3 x 8.0 ❷
❶
CAUTION !
Please start installing
in the order shown.
Image Sensor 1/2.8” SONY EXMOR R Progressive Scan CMOS
Eective Pixels 1945(H) x 1097(V)
Unit cell size (um) 2.9(H) x 2.9(V)
Video Output EX-SDI/HD-SDI: 1080p@25(30)fps/720p@50(60)fps/720p25(30)fps
TV out: CVBS NTSC / PAL (720H)
Transmission
Distance
HD-SDI: Color 150m(5C-HFBT)
EX-SDI1.0: Color 300m(5C-HFBT)
EX-SDI 2.0_2.1 Color 500m(5C-HFBT
(A)
)
Minimum
Illumination 0.2 Lux (F2.0, AGC:33dB, DSS:x2)
Shutter speed 1/30(25)s ~ 1/30,000s
Day/Night AUTO, COLOR, BW
Back/High Light
Compensation OFF / BLC / HLC / WDR selectable
Motion Detection OFF / ON
Privacy Masking 16 selectable zones
White Balance AUTO / AUTO EXT / PUSH LOCK / MANUAL
Functions FLIP(OFF, H, V, H/V), 3DNR, DEFOG, DSS, Digital Zoom, RS-485
Lens Fixed Board / Pinhole Lens
Operating
Temperature -10℃ ~ +50℃ (14℉ ~ 122℉)
Storage
Temperature -20℃ ~ +60℃ (-4℉ ~ 140℉)
Humidity Less than 80%
Power
Consumption 12VDC(±10%), Max.150mA
Dimension(mm) 30mm X 30mm
Weight Approx. 28.9g (Board lens)
• Design and specication are subject to change without notice.
• Basic specication
• Option specication
12V REGULATED
POWER SUPPLY
CVBS
RS485
EX-SDI
HD-SDI
BNC COLOR - YELLOW
White (RS485-)
Orange (RS485+)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
White(RS485-)
Black(RS485+)
↓
_ _ _ _ _ _ _ _ _ _ _ _ _
ABCDEFGHIJKLMN
OPQRSTUVWXYZ!?
0123456789~()^
SP> <BK
1. Communication Specification
RS-485
RateBaud Default 9600bps
Data bits 8 bits
Stop bits 1 bits
CAM ID Default "1"
Parity Check None
Supported Protocol PELCO-D, PELCO-P
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is an XOR sum of Byte1 ~ Byte7
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
• PELCO-D
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7
UP KEY 0 x FF Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F ChkSum
DOWN KEY 0 x FF Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F ChkSum
LEFT KEY 0 x FF Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 ChkSum
RIGHT KEY 0 x FF Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 ChkSum
MENU ENTER
KEY 0 x FF Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F ChkSum
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7 BYTE 8
UP KEY 0 x A0 Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F 0 x AF ChkSum
DOWN KEY 0 x A0 Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F 0 x AF ChkSum
LEFT KEY 0 x A0 Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 0 x AF ChkSum
RIGHT KEY 0 x A0 Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 0 x AF ChkSum
MENU ENTER
KEY 0 x A0 Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F 0 x AF ChkSum
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is the 8 bit (modulo 256) sum of the payload bytes
(Byte2 ~ Byte6) in the Command.
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
2. PELCO protocol for OSD remote control
• PELCO-P
12V REGULATED
POWER SUPPLY
CVBS
EX-SDI
HD-SDI
JOYSTICK
BNC COLOR - YELLOW
White (AD-KEY)
Black (GND)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
6. CAMERA MOUNTING POSITION 7. CONNECTION 8. SPECIFICATION
9. OSD MENU STRUCTURE
• Menu structure
10. HIDDEN MENU
• CONVERT SDI OUTPUT MODE
STEP 1. ENTER
RS485 : Press [LEFT] → [LEFT] → [RIGHT] →[RIGHT] key.
AD-KEY : Press UP/DOWN/LEFT/RIGHT key 3 times.
SETP 2. SELECT
Press UP key 5 times : EX-SDI 2.1
Press DOWN key 5 times : EX-SDI 2.0
Press LEFT key 5 times : HD-SDI
Press RIGHT key 5 times : EX-SDI 1.0
STEP 3. CONFIRM
If the 'YES' is not checked within 30sec, the value returns to the previous setting.
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
LENS
LENS TYPE ELC
LENS MODE NORMAL/DEBLUR
RETURN
EXPOSURE
BRIGHTNESS 0~20
SHUTTER MODE AUTO/MANUAL/
FLICKER
SHUTTER SPEED 1/30(25),1/60(50),1/120(100),1/250,1/500,1/1000,1/2000,1/4
000,1/8000,1/16000,1/30000
DSS OFF/X2/X4/X8/X16/
X32
AGC MAX OFF,3dB~45dB
INITIAL
RETURN
WHITE BALANCE
WB MODE AUTO/AUTO EXT/PUSH LOCK/MANUAL
PUSH AUTO [ ]
COLOR GAIN 0~20
KELVIN LOW/MIDDLE/HIGH
RED GAIN 0~20
BLUE GAIN 0~20
INITIAL
RETURN
WDR/BLC
MODE OFF/BLC/HLC/WDR
LEVEL 0~20
X-POSITION 0~20
Y-POSITION 0~20
X-SIZE 0~20
Y-SIZE 0~20
COLOR BLACK/WHITE/YELLOW/CYAN/GREEN/MAGENTA/RED/BLUE
INITIAL
RETURN
DAY&NIGHT
MODE AUTO/DAY(COLOR)/NIGHT(BW)
DWLL TIME 0~20 sec
D>N THRES 1~35
N>D THRES 0~34
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
IMAGE
SHARPNESS 0~10
GAMMA 0.45/0.50/0.55/0.6
0/0.65/0.70/0.75
FLIP OFF/H-FLIP/
V-FLIP/HV-FLIP
D-WDR OFF/ON
DNR OFF/LOW/MIDDLE/
HIGH
DZOOM x1.0 ~ x16
DEFOG OFF/ON
MODE AUTO/MANUAL
LEVEL LOW/MIDDLE/HIGH
RETURN
INITIAL
RETURN
SPECIAL
CAM TITLE OFF/ON
EDIT PANEL
POSITION [POSITION EDIT]
RETURN
PRIVACY OFF/ON
ZONE NO 0~15
MASK MODE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
COLOR
WHITE/YELLOW/
CYAN/GREEN/
MAGENTA/RED/
BLUE
TRANSPARENCY 0%/33%/66%/100%
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
SPECIAL
MOTION OFF/ON
ZONE NO 0~3
WINDOW USE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
SENSITIVITY 0~10
ALAM MODE OSD/TEXT
INITIAL
RETURN
SYSTEM
FREMARATE 1080p30/1080p25/720p60/720p50/720p
30/720p25
SDI OUT HD-SDI/EX-SD 1.0/ EX-SD 2.0/ EX-SD 2.1
ANALOG OUT CVBS
APPLY YES
LANGUAGE English / Japanese / Russian / Spanish
/ German /France/ Portuguese / Korean
RETURN
INITIAL
RETURN
FACTORY DEF
EXIT
Mounting
bracket
Camera
M2 x 2.5
❶
Tapping
3 x 8.0 ❷
❶
CAUTION !
Please start installing
in the order shown.
Image Sensor 1/2.8” SONY EXMOR R Progressive Scan CMOS
Eective Pixels 1945(H) x 1097(V)
Unit cell size (um) 2.9(H) x 2.9(V)
Video Output EX-SDI/HD-SDI: 1080p@25(30)fps/720p@50(60)fps/720p25(30)fps
TV out: CVBS NTSC / PAL (720H)
Transmission
Distance
HD-SDI: Color 150m(5C-HFBT)
EX-SDI1.0: Color 300m(5C-HFBT)
EX-SDI 2.0_2.1 Color 500m(5C-HFBT
(A)
)
Minimum
Illumination 0.2 Lux (F2.0, AGC:33dB, DSS:x2)
Shutter speed 1/30(25)s ~ 1/30,000s
Day/Night AUTO, COLOR, BW
Back/High Light
Compensation OFF / BLC / HLC / WDR selectable
Motion Detection OFF / ON
Privacy Masking 16 selectable zones
White Balance AUTO / AUTO EXT / PUSH LOCK / MANUAL
Functions FLIP(OFF, H, V, H/V), 3DNR, DEFOG, DSS, Digital Zoom, RS-485
Lens Fixed Board / Pinhole Lens
Operating
Temperature -10℃ ~ +50℃ (14℉ ~ 122℉)
Storage
Temperature -20℃ ~ +60℃ (-4℉ ~ 140℉)
Humidity Less than 80%
Power
Consumption 12VDC(±10%), Max.150mA
Dimension(mm) 30mm X 30mm
Weight Approx. 28.9g (Board lens)
• Design and specication are subject to change without notice.
• Basic specication
• Option specication
12V REGULATED
POWER SUPPLY
CVBS
RS485
EX-SDI
HD-SDI
BNC COLOR - YELLOW
White (RS485-)
Orange (RS485+)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
White(RS485-)
Black(RS485+)
↓
_ _ _ _ _ _ _ _ _ _ _ _ _
ABCDEFGHIJKLMN
OPQRSTUVWXYZ!?
0123456789~()^
SP> <BK
1. Communication Specification
RS-485
RateBaud Default 9600bps
Data bits 8 bits
Stop bits 1 bits
CAM ID Default "1"
Parity Check None
Supported Protocol PELCO-D, PELCO-P
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is an XOR sum of Byte1 ~ Byte7
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
• PELCO-D
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7
UP KEY 0 x FF Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F ChkSum
DOWN KEY 0 x FF Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F ChkSum
LEFT KEY 0 x FF Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 ChkSum
RIGHT KEY 0 x FF Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 ChkSum
MENU ENTER
KEY 0 x FF Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F ChkSum
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7 BYTE 8
UP KEY 0 x A0 Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F 0 x AF ChkSum
DOWN KEY 0 x A0 Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F 0 x AF ChkSum
LEFT KEY 0 x A0 Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 0 x AF ChkSum
RIGHT KEY 0 x A0 Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 0 x AF ChkSum
MENU ENTER
KEY 0 x A0 Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F 0 x AF ChkSum
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is the 8 bit (modulo 256) sum of the payload bytes
(Byte2 ~ Byte6) in the Command.
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
2. PELCO protocol for OSD remote control
• PELCO-P
12V REGULATED
POWER SUPPLY
CVBS
EX-SDI
HD-SDI
JOYSTICK
BNC COLOR - YELLOW
White (AD-KEY)
Black (GND)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
6. CAMERA MOUNTING POSITION 7. CONNECTION 8. SPECIFICATION
9. OSD MENU STRUCTURE
• Menu structure
10. HIDDEN MENU
• CONVERT SDI OUTPUT MODE
STEP 1. ENTER
RS485 : Press [LEFT] → [LEFT] → [RIGHT] →[RIGHT] key.
AD-KEY : Press UP/DOWN/LEFT/RIGHT key 3 times.
SETP 2. SELECT
Press UP key 5 times : EX-SDI 2.1
Press DOWN key 5 times : EX-SDI 2.0
Press LEFT key 5 times : HD-SDI
Press RIGHT key 5 times : EX-SDI 1.0
STEP 3. CONFIRM
If the 'YES' is not checked within 30sec, the value returns to the previous setting.
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
LENS
LENS TYPE ELC
LENS MODE NORMAL/DEBLUR
RETURN
EXPOSURE
BRIGHTNESS 0~20
SHUTTER MODE AUTO/MANUAL/
FLICKER
SHUTTER SPEED 1/30(25),1/60(50),1/120(100),1/250,1/500,1/1000,1/2000,1/4
000,1/8000,1/16000,1/30000
DSS OFF/X2/X4/X8/X16/
X32
AGC MAX OFF,3dB~45dB
INITIAL
RETURN
WHITE BALANCE
WB MODE AUTO/AUTO EXT/PUSH LOCK/MANUAL
PUSH AUTO [ ]
COLOR GAIN 0~20
KELVIN LOW/MIDDLE/HIGH
RED GAIN 0~20
BLUE GAIN 0~20
INITIAL
RETURN
WDR/BLC
MODE OFF/BLC/HLC/WDR
LEVEL 0~20
X-POSITION 0~20
Y-POSITION 0~20
X-SIZE 0~20
Y-SIZE 0~20
COLOR BLACK/WHITE/YELLOW/CYAN/GREEN/MAGENTA/RED/BLUE
INITIAL
RETURN
DAY&NIGHT
MODE AUTO/DAY(COLOR)/NIGHT(BW)
DWLL TIME 0~20 sec
D>N THRES 1~35
N>D THRES 0~34
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
IMAGE
SHARPNESS 0~10
GAMMA 0.45/0.50/0.55/0.6
0/0.65/0.70/0.75
FLIP OFF/H-FLIP/
V-FLIP/HV-FLIP
D-WDR OFF/ON
DNR OFF/LOW/MIDDLE/
HIGH
DZOOM x1.0 ~ x16
DEFOG OFF/ON
MODE AUTO/MANUAL
LEVEL LOW/MIDDLE/HIGH
RETURN
INITIAL
RETURN
SPECIAL
CAM TITLE OFF/ON
EDIT PANEL
POSITION [POSITION EDIT]
RETURN
PRIVACY OFF/ON
ZONE NO 0~15
MASK MODE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
COLOR
WHITE/YELLOW/
CYAN/GREEN/
MAGENTA/RED/
BLUE
TRANSPARENCY 0%/33%/66%/100%
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
SPECIAL
MOTION OFF/ON
ZONE NO 0~3
WINDOW USE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
SENSITIVITY 0~10
ALAM MODE OSD/TEXT
INITIAL
RETURN
SYSTEM
FREMARATE 1080p30/1080p25/720p60/720p50/720p
30/720p25
SDI OUT HD-SDI/EX-SD 1.0/ EX-SD 2.0/ EX-SD 2.1
ANALOG OUT CVBS
APPLY YES
LANGUAGE English / Japanese / Russian / Spanish
/ German /France/ Portuguese / Korean
RETURN
INITIAL
RETURN
FACTORY DEF
EXIT
Mounting
bracket
Camera
M2 x 2.5
❶
Tapping
3 x 8.0 ❷
❶
CAUTION !
Please start installing
in the order shown.
Image Sensor 1/2.8” SONY EXMOR R Progressive Scan CMOS
Eective Pixels 1945(H) x 1097(V)
Unit cell size (um) 2.9(H) x 2.9(V)
Video Output EX-SDI/HD-SDI: 1080p@25(30)fps/720p@50(60)fps/720p25(30)fps
TV out: CVBS NTSC / PAL (720H)
Transmission
Distance
HD-SDI: Color 150m(5C-HFBT)
EX-SDI1.0: Color 300m(5C-HFBT)
EX-SDI 2.0_2.1 Color 500m(5C-HFBT
(A)
)
Minimum
Illumination 0.2 Lux (F2.0, AGC:33dB, DSS:x2)
Shutter speed 1/30(25)s ~ 1/30,000s
Day/Night AUTO, COLOR, BW
Back/High Light
Compensation OFF / BLC / HLC / WDR selectable
Motion Detection OFF / ON
Privacy Masking 16 selectable zones
White Balance AUTO / AUTO EXT / PUSH LOCK / MANUAL
Functions FLIP(OFF, H, V, H/V), 3DNR, DEFOG, DSS, Digital Zoom, RS-485
Lens Fixed Board / Pinhole Lens
Operating
Temperature -10℃ ~ +50℃ (14℉ ~ 122℉)
Storage
Temperature -20℃ ~ +60℃ (-4℉ ~ 140℉)
Humidity Less than 80%
Power
Consumption 12VDC(±10%), Max.150mA
Dimension(mm) 30mm X 30mm
Weight Approx. 28.9g (Board lens)
• Design and specication are subject to change without notice.
• Basic specication
• Option specication
12V REGULATED
POWER SUPPLY
CVBS
RS485
EX-SDI
HD-SDI
BNC COLOR - YELLOW
White (RS485-)
Orange (RS485+)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
White(RS485-)
Black(RS485+)
↓
_ _ _ _ _ _ _ _ _ _ _ _ _
ABCDEFGHIJKLMN
OPQRSTUVWXYZ!?
0123456789~()^
SP> <BK
1. Communication Specification
RS-485
RateBaud Default 9600bps
Data bits 8 bits
Stop bits 1 bits
CAM ID Default "1"
Parity Check None
Supported Protocol PELCO-D, PELCO-P
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is an XOR sum of Byte1 ~ Byte7
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
• PELCO-D
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7
UP KEY 0 x FF Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F ChkSum
DOWN KEY 0 x FF Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F ChkSum
LEFT KEY 0 x FF Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 ChkSum
RIGHT KEY 0 x FF Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 ChkSum
MENU ENTER
KEY 0 x FF Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F ChkSum
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7 BYTE 8
UP KEY 0 x A0 Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F 0 x AF ChkSum
DOWN KEY 0 x A0 Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F 0 x AF ChkSum
LEFT KEY 0 x A0 Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 0 x AF ChkSum
RIGHT KEY 0 x A0 Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 0 x AF ChkSum
MENU ENTER
KEY 0 x A0 Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F 0 x AF ChkSum
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is the 8 bit (modulo 256) sum of the payload bytes
(Byte2 ~ Byte6) in the Command.
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
2. PELCO protocol for OSD remote control
• PELCO-P
12V REGULATED
POWER SUPPLY
CVBS
EX-SDI
HD-SDI
JOYSTICK
BNC COLOR - YELLOW
White (AD-KEY)
Black (GND)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
6. CAMERA MOUNTING POSITION 7. CONNECTION 8. SPECIFICATION
9. OSD MENU STRUCTURE
• Menu structure
10. HIDDEN MENU
• CONVERT SDI OUTPUT MODE
STEP 1. ENTER
RS485 : Press [LEFT] → [LEFT] → [RIGHT] →[RIGHT] key.
AD-KEY : Press UP/DOWN/LEFT/RIGHT key 3 times.
SETP 2. SELECT
Press UP key 5 times : EX-SDI 2.1
Press DOWN key 5 times : EX-SDI 2.0
Press LEFT key 5 times : HD-SDI
Press RIGHT key 5 times : EX-SDI 1.0
STEP 3. CONFIRM
If the 'YES' is not checked within 30sec, the value returns to the previous setting.
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
LENS
LENS TYPE ELC
LENS MODE NORMAL/DEBLUR
RETURN
EXPOSURE
BRIGHTNESS 0~20
SHUTTER MODE AUTO/MANUAL/
FLICKER
SHUTTER SPEED 1/30(25),1/60(50),1/120(100),1/250,1/500,1/1000,1/2000,1/4
000,1/8000,1/16000,1/30000
DSS OFF/X2/X4/X8/X16/
X32
AGC MAX OFF,3dB~45dB
INITIAL
RETURN
WHITE BALANCE
WB MODE AUTO/AUTO EXT/PUSH LOCK/MANUAL
PUSH AUTO [ ]
COLOR GAIN 0~20
KELVIN LOW/MIDDLE/HIGH
RED GAIN 0~20
BLUE GAIN 0~20
INITIAL
RETURN
WDR/BLC
MODE OFF/BLC/HLC/WDR
LEVEL 0~20
X-POSITION 0~20
Y-POSITION 0~20
X-SIZE 0~20
Y-SIZE 0~20
COLOR BLACK/WHITE/YELLOW/CYAN/GREEN/MAGENTA/RED/BLUE
INITIAL
RETURN
DAY&NIGHT
MODE AUTO/DAY(COLOR)/NIGHT(BW)
DWLL TIME 0~20 sec
D>N THRES 1~35
N>D THRES 0~34
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
IMAGE
SHARPNESS 0~10
GAMMA 0.45/0.50/0.55/0.6
0/0.65/0.70/0.75
FLIP OFF/H-FLIP/
V-FLIP/HV-FLIP
D-WDR OFF/ON
DNR OFF/LOW/MIDDLE/
HIGH
DZOOM x1.0 ~ x16
DEFOG OFF/ON
MODE AUTO/MANUAL
LEVEL LOW/MIDDLE/HIGH
RETURN
INITIAL
RETURN
SPECIAL
CAM TITLE OFF/ON
EDIT PANEL
POSITION [POSITION EDIT]
RETURN
PRIVACY OFF/ON
ZONE NO 0~15
MASK MODE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
COLOR
WHITE/YELLOW/
CYAN/GREEN/
MAGENTA/RED/
BLUE
TRANSPARENCY 0%/33%/66%/100%
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
SPECIAL
MOTION OFF/ON
ZONE NO 0~3
WINDOW USE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
SENSITIVITY 0~10
ALAM MODE OSD/TEXT
INITIAL
RETURN
SYSTEM
FREMARATE 1080p30/1080p25/720p60/720p50/720p
30/720p25
SDI OUT HD-SDI/EX-SD 1.0/ EX-SD 2.0/ EX-SD 2.1
ANALOG OUT CVBS
APPLY YES
LANGUAGE English / Japanese / Russian / Spanish
/ German /France/ Portuguese / Korean
RETURN
INITIAL
RETURN
FACTORY DEF
EXIT
Mounting
bracket
Camera
M2 x 2.5
❶
Tapping
3 x 8.0 ❷
❶
CAUTION !
Please start installing
in the order shown.
Image Sensor 1/2.8” SONY EXMOR R Progressive Scan CMOS
Eective Pixels 1945(H) x 1097(V)
Unit cell size (um) 2.9(H) x 2.9(V)
Video Output EX-SDI/HD-SDI: 1080p@25(30)fps/720p@50(60)fps/720p25(30)fps
TV out: CVBS NTSC / PAL (720H)
Transmission
Distance
HD-SDI: Color 150m(5C-HFBT)
EX-SDI1.0: Color 300m(5C-HFBT)
EX-SDI 2.0_2.1 Color 500m(5C-HFBT
(A)
)
Minimum
Illumination 0.2 Lux (F2.0, AGC:33dB, DSS:x2)
Shutter speed 1/30(25)s ~ 1/30,000s
Day/Night AUTO, COLOR, BW
Back/High Light
Compensation OFF / BLC / HLC / WDR selectable
Motion Detection OFF / ON
Privacy Masking 16 selectable zones
White Balance AUTO / AUTO EXT / PUSH LOCK / MANUAL
Functions FLIP(OFF, H, V, H/V), 3DNR, DEFOG, DSS, Digital Zoom, RS-485
Lens Fixed Board / Pinhole Lens
Operating
Temperature -10℃ ~ +50℃ (14℉ ~ 122℉)
Storage
Temperature -20℃ ~ +60℃ (-4℉ ~ 140℉)
Humidity Less than 80%
Power
Consumption 12VDC(±10%), Max.150mA
Dimension(mm) 30mm X 30mm
Weight Approx. 28.9g (Board lens)
• Design and specication are subject to change without notice.
• Basic specication
• Option specication
12V REGULATED
POWER SUPPLY
CVBS
RS485
EX-SDI
HD-SDI
BNC COLOR - YELLOW
White (RS485-)
Orange (RS485+)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
White(RS485-)
Black(RS485+)
↓
_ _ _ _ _ _ _ _ _ _ _ _ _
ABCDEFGHIJKLMN
OPQRSTUVWXYZ!?
0123456789~()^
SP> <BK
1. Communication Specification
RS-485
RateBaud Default 9600bps
Data bits 8 bits
Stop bits 1 bits
CAM ID Default "1"
Parity Check None
Supported Protocol PELCO-D, PELCO-P
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is an XOR sum of Byte1 ~ Byte7
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
• PELCO-D
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7
UP KEY 0 x FF Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F ChkSum
DOWN KEY 0 x FF Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F ChkSum
LEFT KEY 0 x FF Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 ChkSum
RIGHT KEY 0 x FF Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 ChkSum
MENU ENTER
KEY 0 x FF Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F ChkSum
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7 BYTE 8
UP KEY 0 x A0 Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F 0 x AF ChkSum
DOWN KEY 0 x A0 Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F 0 x AF ChkSum
LEFT KEY 0 x A0 Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 0 x AF ChkSum
RIGHT KEY 0 x A0 Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 0 x AF ChkSum
MENU ENTER
KEY 0 x A0 Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F 0 x AF ChkSum
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is the 8 bit (modulo 256) sum of the payload bytes
(Byte2 ~ Byte6) in the Command.
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
2. PELCO protocol for OSD remote control
• PELCO-P
12V REGULATED
POWER SUPPLY
CVBS
EX-SDI
HD-SDI
JOYSTICK
BNC COLOR - YELLOW
White (AD-KEY)
Black (GND)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
6. CAMERA MOUNTING POSITION 7. CONNECTION 8. SPECIFICATION
9. OSD MENU STRUCTURE
• Menu structure
10. HIDDEN MENU
• CONVERT SDI OUTPUT MODE
STEP 1. ENTER
RS485 : Press [LEFT] → [LEFT] → [RIGHT] →[RIGHT] key.
AD-KEY : Press UP/DOWN/LEFT/RIGHT key 3 times.
SETP 2. SELECT
Press UP key 5 times : EX-SDI 2.1
Press DOWN key 5 times : EX-SDI 2.0
Press LEFT key 5 times : HD-SDI
Press RIGHT key 5 times : EX-SDI 1.0
STEP 3. CONFIRM
If the 'YES' is not checked within 30sec, the value returns to the previous setting.
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
LENS
LENS TYPE ELC
LENS MODE NORMAL/DEBLUR
RETURN
EXPOSURE
BRIGHTNESS 0~20
SHUTTER MODE AUTO/MANUAL/
FLICKER
SHUTTER SPEED 1/30(25),1/60(50),1/120(100),1/250,1/500,1/1000,1/2000,1/4
000,1/8000,1/16000,1/30000
DSS OFF/X2/X4/X8/X16/
X32
AGC MAX OFF,3dB~45dB
INITIAL
RETURN
WHITE BALANCE
WB MODE AUTO/AUTO EXT/PUSH LOCK/MANUAL
PUSH AUTO [ ]
COLOR GAIN 0~20
KELVIN LOW/MIDDLE/HIGH
RED GAIN 0~20
BLUE GAIN 0~20
INITIAL
RETURN
WDR/BLC
MODE OFF/BLC/HLC/WDR
LEVEL 0~20
X-POSITION 0~20
Y-POSITION 0~20
X-SIZE 0~20
Y-SIZE 0~20
COLOR BLACK/WHITE/YELLOW/CYAN/GREEN/MAGENTA/RED/BLUE
INITIAL
RETURN
DAY&NIGHT
MODE AUTO/DAY(COLOR)/NIGHT(BW)
DWLL TIME 0~20 sec
D>N THRES 1~35
N>D THRES 0~34
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
IMAGE
SHARPNESS 0~10
GAMMA 0.45/0.50/0.55/0.6
0/0.65/0.70/0.75
FLIP OFF/H-FLIP/
V-FLIP/HV-FLIP
D-WDR OFF/ON
DNR OFF/LOW/MIDDLE/
HIGH
DZOOM x1.0 ~ x16
DEFOG OFF/ON
MODE AUTO/MANUAL
LEVEL LOW/MIDDLE/HIGH
RETURN
INITIAL
RETURN
SPECIAL
CAM TITLE OFF/ON
EDIT PANEL
POSITION [POSITION EDIT]
RETURN
PRIVACY OFF/ON
ZONE NO 0~15
MASK MODE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
COLOR
WHITE/YELLOW/
CYAN/GREEN/
MAGENTA/RED/
BLUE
TRANSPARENCY 0%/33%/66%/100%
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
SPECIAL
MOTION OFF/ON
ZONE NO 0~3
WINDOW USE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
SENSITIVITY 0~10
ALAM MODE OSD/TEXT
INITIAL
RETURN
SYSTEM
FREMARATE 1080p30/1080p25/720p60/720p50/720p
30/720p25
SDI OUT HD-SDI/EX-SD 1.0/ EX-SD 2.0/ EX-SD 2.1
ANALOG OUT CVBS
APPLY YES
LANGUAGE English / Japanese / Russian / Spanish
/ German /France/ Portuguese / Korean
RETURN
INITIAL
RETURN
FACTORY DEF
EXIT
Mounting
bracket
Camera
M2 x 2.5
❶
Tapping
3 x 8.0 ❷
❶
CAUTION !
Please start installing
in the order shown.
Image Sensor 1/2.8” SONY EXMOR R Progressive Scan CMOS
Eective Pixels 1945(H) x 1097(V)
Unit cell size (um) 2.9(H) x 2.9(V)
Video Output EX-SDI/HD-SDI: 1080p@25(30)fps/720p@50(60)fps/720p25(30)fps
TV out: CVBS NTSC / PAL (720H)
Transmission
Distance
HD-SDI: Color 150m(5C-HFBT)
EX-SDI1.0: Color 300m(5C-HFBT)
EX-SDI 2.0_2.1 Color 500m(5C-HFBT
(A)
)
Minimum
Illumination 0.2 Lux (F2.0, AGC:33dB, DSS:x2)
Shutter speed 1/30(25)s ~ 1/30,000s
Day/Night AUTO, COLOR, BW
Back/High Light
Compensation OFF / BLC / HLC / WDR selectable
Motion Detection OFF / ON
Privacy Masking 16 selectable zones
White Balance AUTO / AUTO EXT / PUSH LOCK / MANUAL
Functions FLIP(OFF, H, V, H/V), 3DNR, DEFOG, DSS, Digital Zoom, RS-485
Lens Fixed Board / Pinhole Lens
Operating
Temperature -10℃ ~ +50℃ (14℉ ~ 122℉)
Storage
Temperature -20℃ ~ +60℃ (-4℉ ~ 140℉)
Humidity Less than 80%
Power
Consumption 12VDC(±10%), Max.150mA
Dimension(mm) 30mm X 30mm
Weight Approx. 28.9g (Board lens)
• Design and specication are subject to change without notice.
• Basic specication
• Option specication
12V REGULATED
POWER SUPPLY
CVBS
RS485
EX-SDI
HD-SDI
BNC COLOR - YELLOW
White (RS485-)
Orange (RS485+)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
White(RS485-)
Black(RS485+)
↓
_ _ _ _ _ _ _ _ _ _ _ _ _
ABCDEFGHIJKLMN
OPQRSTUVWXYZ!?
0123456789~()^
SP> <BK
1. Communication Specification
RS-485
RateBaud Default 9600bps
Data bits 8 bits
Stop bits 1 bits
CAM ID Default "1"
Parity Check None
Supported Protocol PELCO-D, PELCO-P
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is an XOR sum of Byte1 ~ Byte7
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
• PELCO-D
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7
UP KEY 0 x FF Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F ChkSum
DOWN KEY 0 x FF Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F ChkSum
LEFT KEY 0 x FF Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 ChkSum
RIGHT KEY 0 x FF Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 ChkSum
MENU ENTER
KEY 0 x FF Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F ChkSum
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7 BYTE 8
UP KEY 0 x A0 Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F 0 x AF ChkSum
DOWN KEY 0 x A0 Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F 0 x AF ChkSum
LEFT KEY 0 x A0 Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 0 x AF ChkSum
RIGHT KEY 0 x A0 Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 0 x AF ChkSum
MENU ENTER
KEY 0 x A0 Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F 0 x AF ChkSum
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is the 8 bit (modulo 256) sum of the payload bytes
(Byte2 ~ Byte6) in the Command.
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
2. PELCO protocol for OSD remote control
• PELCO-P
12V REGULATED
POWER SUPPLY
CVBS
EX-SDI
HD-SDI
JOYSTICK
BNC COLOR - YELLOW
White (AD-KEY)
Black (GND)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
6. CAMERA MOUNTING POSITION 7. CONNECTION 8. SPECIFICATION
9. OSD MENU STRUCTURE
• Menu structure
10. HIDDEN MENU
• CONVERT SDI OUTPUT MODE
STEP 1. ENTER
RS485 : Press [LEFT] → [LEFT] → [RIGHT] →[RIGHT] key.
AD-KEY : Press UP/DOWN/LEFT/RIGHT key 3 times.
SETP 2. SELECT
Press UP key 5 times : EX-SDI 2.1
Press DOWN key 5 times : EX-SDI 2.0
Press LEFT key 5 times : HD-SDI
Press RIGHT key 5 times : EX-SDI 1.0
STEP 3. CONFIRM
If the 'YES' is not checked within 30sec, the value returns to the previous setting.
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
LENS
LENS TYPE ELC
LENS MODE NORMAL/DEBLUR
RETURN
EXPOSURE
BRIGHTNESS 0~20
SHUTTER MODE AUTO/MANUAL/
FLICKER
SHUTTER SPEED 1/30(25),1/60(50),1/120(100),1/250,1/500,1/1000,1/2000,1/4
000,1/8000,1/16000,1/30000
DSS OFF/X2/X4/X8/X16/
X32
AGC MAX OFF,3dB~45dB
INITIAL
RETURN
WHITE BALANCE
WB MODE AUTO/AUTO EXT/PUSH LOCK/MANUAL
PUSH AUTO [ ]
COLOR GAIN 0~20
KELVIN LOW/MIDDLE/HIGH
RED GAIN 0~20
BLUE GAIN 0~20
INITIAL
RETURN
WDR/BLC
MODE OFF/BLC/HLC/WDR
LEVEL 0~20
X-POSITION 0~20
Y-POSITION 0~20
X-SIZE 0~20
Y-SIZE 0~20
COLOR BLACK/WHITE/YELLOW/CYAN/GREEN/MAGENTA/RED/BLUE
INITIAL
RETURN
DAY&NIGHT
MODE AUTO/DAY(COLOR)/NIGHT(BW)
DWLL TIME 0~20 sec
D>N THRES 1~35
N>D THRES 0~34
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
IMAGE
SHARPNESS 0~10
GAMMA 0.45/0.50/0.55/0.6
0/0.65/0.70/0.75
FLIP OFF/H-FLIP/
V-FLIP/HV-FLIP
D-WDR OFF/ON
DNR OFF/LOW/MIDDLE/
HIGH
DZOOM x1.0 ~ x16
DEFOG OFF/ON
MODE AUTO/MANUAL
LEVEL LOW/MIDDLE/HIGH
RETURN
INITIAL
RETURN
SPECIAL
CAM TITLE OFF/ON
EDIT PANEL
POSITION [POSITION EDIT]
RETURN
PRIVACY OFF/ON
ZONE NO 0~15
MASK MODE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
COLOR
WHITE/YELLOW/
CYAN/GREEN/
MAGENTA/RED/
BLUE
TRANSPARENCY 0%/33%/66%/100%
INITIAL
RETURN
1’ST ITEM 2’ND ITEM 3’RD ITEM or DATA 4’TH ITEM or DATA 5’TH ITEM or DATA
SPECIAL
MOTION OFF/ON
ZONE NO 0~3
WINDOW USE OFF/ON
X-POSITION 0~60
Y-POSITION 0~34
X-SIZE 0~60
Y-SIZE 0~34
SENSITIVITY 0~10
ALAM MODE OSD/TEXT
INITIAL
RETURN
SYSTEM
FREMARATE 1080p30/1080p25/720p60/720p50/720p
30/720p25
SDI OUT HD-SDI/EX-SD 1.0/ EX-SD 2.0/ EX-SD 2.1
ANALOG OUT CVBS
APPLY YES
LANGUAGE English / Japanese / Russian / Spanish
/ German /France/ Portuguese / Korean
RETURN
INITIAL
RETURN
FACTORY DEF
EXIT
Mounting
bracket
Camera
M2 x 2.5
❶
Tapping
3 x 8.0 ❷
❶
CAUTION !
Please start installing
in the order shown.
Image Sensor 1/2.8” SONY EXMOR R Progressive Scan CMOS
Eective Pixels 1945(H) x 1097(V)
Unit cell size (um) 2.9(H) x 2.9(V)
Video Output EX-SDI/HD-SDI: 1080p@25(30)fps/720p@50(60)fps/720p25(30)fps
TV out: CVBS NTSC / PAL (720H)
Transmission
Distance
HD-SDI: Color 150m(5C-HFBT)
EX-SDI1.0: Color 300m(5C-HFBT)
EX-SDI 2.0_2.1 Color 500m(5C-HFBT
(A)
)
Minimum
Illumination 0.2 Lux (F2.0, AGC:33dB, DSS:x2)
Shutter speed 1/30(25)s ~ 1/30,000s
Day/Night AUTO, COLOR, BW
Back/High Light
Compensation OFF / BLC / HLC / WDR selectable
Motion Detection OFF / ON
Privacy Masking 16 selectable zones
White Balance AUTO / AUTO EXT / PUSH LOCK / MANUAL
Functions FLIP(OFF, H, V, H/V), 3DNR, DEFOG, DSS, Digital Zoom, RS-485
Lens Fixed Board / Pinhole Lens
Operating
Temperature -10℃ ~ +50℃ (14℉ ~ 122℉)
Storage
Temperature -20℃ ~ +60℃ (-4℉ ~ 140℉)
Humidity Less than 80%
Power
Consumption 12VDC(±10%), Max.150mA
Dimension(mm) 30mm X 30mm
Weight Approx. 28.9g (Board lens)
• Design and specication are subject to change without notice.
• Basic specication
• Option specication
12V REGULATED
POWER SUPPLY
CVBS
RS485
EX-SDI
HD-SDI
BNC COLOR - YELLOW
White (RS485-)
Orange (RS485+)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
White(RS485-)
Black(RS485+)
↓
_ _ _ _ _ _ _ _ _ _ _ _ _
ABCDEFGHIJKLMN
OPQRSTUVWXYZ!?
0123456789~()^
SP> <BK
1. Communication Specification
RS-485
RateBaud Default 9600bps
Data bits 8 bits
Stop bits 1 bits
CAM ID Default "1"
Parity Check None
Supported Protocol PELCO-D, PELCO-P
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is an XOR sum of Byte1 ~ Byte7
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
• PELCO-D
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7
UP KEY 0 x FF Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F ChkSum
DOWN KEY 0 x FF Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F ChkSum
LEFT KEY 0 x FF Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 ChkSum
RIGHT KEY 0 x FF Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 ChkSum
MENU ENTER
KEY 0 x FF Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F ChkSum
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7 BYTE 8
UP KEY 0 x A0 Cam ID 0 x 00 0 x 08 0 x 00 0x0B~0x3F 0 x AF ChkSum
DOWN KEY 0 x A0 Cam ID 0 x 00 0 x 10 0 x 00 0x0B~0x3F 0 x AF ChkSum
LEFT KEY 0 x A0 Cam ID 0 x 00 0 x 04 0x0B~0x3F 0 x 00 0 x AF ChkSum
RIGHT KEY 0 x A0 Cam ID 0 x 00 0 x 02 0x0B~0x3F 0 x 00 0 x AF ChkSum
MENU ENTER
KEY 0 x A0 Cam ID 0 x 00 0 x 07 0 x 00 0 x 5F 0 x AF ChkSum
- Cam ID : 0x00 ~ 0x1F
- ChkSum : The Check Sum is the 8 bit (modulo 256) sum of the payload bytes
(Byte2 ~ Byte6) in the Command.
- [ 0x0A~0x3F ] means accept any value(between 0x0A ~ 0x3F) on command action.
2. PELCO protocol for OSD remote control
• PELCO-P
12V REGULATED
POWER SUPPLY
CVBS
EX-SDI
HD-SDI
JOYSTICK
BNC COLOR - YELLOW
White (AD-KEY)
Black (GND)
Yellow(VIDEO OUT)
Black (GND)
Red (DC 12V)
Table of contents
