Surefire SF RYDER 9-Ti2 User manual

SOUND SUPPRESSOR FOR 9 mm PISTOLS & RIFLES
with 1/2x28 and M13.5x1 LH THREADS
SF®RYDER 9-Ti2
SF RYDER 9-Ti2-1/2-28
SF RYDER 9-Ti2-M13.5X1 LH
WARRANTY
SureFire warrants our suppressors and suppressor related products to be free from defects in workmanship and materials for the lifetime of the
original owner. We will repair, replace, or refund your original purchase price of a product if it is determined by SureFire to be defective. This warranty
does not cover normal wear and tear, damage to the suppressor resulting in whole or in part from unauthorized repairs, unstable or non-SAAMI/
NATO specification ammunition, abuse, misuse, or neglect. Unwarranted repairs to the suppressor, including but not limited to core rebuilds, made
necessary by any of these factors will be invoiced to the owner who will be given the right to approve such work before it commences. BSD’s and
BFA’s are designed to be used with blank ammunition only. Any damage due to live fired rounds is not covered by this warranty and cannot be
repaired. SureFire assumes no responsibility whatsoever and will honor no claims for damages, regardless of nature, for physical injury or property
damage resulting from careless and/or irresponsible handling, adjustments to the suppressor and/or suppressor related products, neglect or abuse.
DISCLAIMER
The above warranties are exclusive, and to the extent permitted by applicable laws, shall be in lieu of all other warranties, expressed or implied,
including, without limitation, any warranty of merchantability or fitness for a particular use or purpose. SureFire disclaims any and all liability for
product malfunctions, physical injuries, or property damage that result in whole, or in part, from the criminal, negligent, or improper use of the
product: and/or from modifications or alterations thereto. In no event shall SureFire be liable for any incidental, special, or consequential damages
relating to the purchase, use, or performance of any SureFire product.
WARRANTY CLAIMS
For repair or replacement email Technical Support at technicalsupport@surefire.com or contact Customer Service at 800-828-8809 (toll free) or
714-545-9444 and obtain a Return Merchandise Authorization number (RMA#). An initial request for RMA can also be submitted through the link
on www.surefire.com. You may be supplied with additional shipping instructions specific to the product being returned. Package the unit carefully and
in accordance with all instructions then return to the mailing address provided (no CODs please). SureFire will pay any reasonable shipping costs to
return the unit to you. ©2019 SureFire, LLC. All rights reserved.
USER MANUAL
Revision B 07-2020
71-01-1106
SF RYDER 9-Ti2-1/2-28
SF RYDER 9-Ti2-M13.5X1 LH
DOPSR REF# 20-S-1556
18300 MT. BALDY CIRCLE
FOUNTAIN VALLEY, CA 92708-6122
WWW.SUREFIRE.COM
SF®RYDER 9-Ti2
SF RYDER 9-Ti2
CALIBER 9 mm
CONSTRUCTION Titanium Tube, Front Plate, Rear Cap,
Stainless Steel Baffles
COATING Cerakote™Finish
DIAMETER 1.25 in (3.2 cm)
LENGTH 7.8 in (19.8 cm)
ADDED TO WEAPON* 7.4 in (18.8 cm)
WEIGHT 10.7 oz (303 g)
SPECIFICATIONS
PATENT NO.
D682,974

PISTON ASSEMBLY
Place piston into suppressor back section and place spring or
fixed barrel spacer (with spring facing rear) over piston shaft.
Place rear cap over exposed piston shaft, push until flush with
suppressor tube, and tighten until hand tight by turning clockwise.
Note: Rear cap should only be tighten by hand. Tool is only to be
used for disassembly.
DISASSEMBLY
1. Insert the Disassembly/Assembly Tool Central Rod into the bore
of the suppressor front plate. Align the Disassembly/Disassembly
Tool Pins with the blank holes in the suppressor front plate and
push the tool snug against the front plate. (Fig. 1)
2.Rotate the Disassembly/Assembly Tool counterclockwise while
holding or rotating the suppressor clockwise, until the front plate
is unscrewed. (Fig. 2)
3.Push the front plate and baffle stack through the front of the
suppressor tube with the Baffle Removal Tool. The Baffle
Removal Tool is designed to interface with the shear cut of the
baffle. (Fig. 3)
Note: After the suppressor has been shot the baffle stack may become
difficult to push through. If this is the case, place the Baffle Removal
Tool on the Disassembly/Assemble Tool Central Rod and rotate until
it mates with the shear cut on the baffle. Use the tool for leverage to
push the baffle stack through. Remove the Baffle Removal Tool once
the baffle stack has been pushed through the suppressor tube.
CLEANING
The SF RYDER 9-Ti2 should be cleaned periodically to ensure
optimal performance. Recommended cleaning of the suppressor
piston is at least every 300 rounds – and the baffles every 1,000
rounds. Clean the baffles with non-flammable cleaning solvent.
Wipe the baffles dry with a clean, dry cloth or cleaning patches.
Clean sooner if there is noticeable carbon buildup or any sacrifice
in sound attenuation.
ASSEMBLY
1. Slide the front plate onto the Disassembly/Assembly Tool
central rod and align the tool pins with the blank holes in the
front plate.
2. Slide Baffle #1 onto the Disassembly/Assembly Tool Central
rod. Slide Baffle #2 onto the central rod and align index tab
so Baffle #2 can be pushed flush with Baffle #1. Repeat this
process with Baffle #3 through #6,in that order, ensuring that
all of the baffles are flush and the numbering is in alignment.
Next place the spacer on the baffle stack.
3. Slide the suppressor tube over the entire stack.
4. Rotate the Disassembly/Assembly Tool counterclockwise,
while holding the suppressor tube or rotate suppressor tube
clockwise until hand tight. Slide the Disassembly/Assembly
Tool out from the suppressor.
SF®RYDER 9-Ti2
INTRODUCTION
The SureFire RYDER 9-Ti2 is a lightweight suppressor optimized for
9mmpistols andrifleswith1/2x28 orM13.5x1LHthreadedmuzzles.
The suppressor features a durable yet lightweight titanium body
with rounded ends and flutes to reduce weight with no sacrifice in
strength. It is finished in a durable Cerakote coating and internally
has patented stainless baffles that provide superior sound
attenuation and reduce muzzle blast. Additionally the SF-SPCR-
9Ti2 Fixed Barrel Spacer (sold separately) is recommended when
shooting a fixed-barrel firearm, or a 9 mm carbine weapon system.
KIT CONTENTS
The SF RYDER 9-Ti2 ships standard with the following items:
• SF RYDER 9-Ti2 Suppressor (assembled)
• Disassembly/Assembly Tool
• Baffle Removal Tool
• Suppressor Holster
• User Manual
ATTACHMENT/REMOVAL
To attach the SF RYDER 9-Ti2, align the muzzle threads with
the suppressor threaded piston and screw the suppressor on
clockwise (or counterclockwise with the M13.5x1 LH) until
hand tight.
To remove the SF RYDER 9-Ti2, unscrew the suppressor
counterclockwise (or clockwise for the M13.5x1 LH) and remove
the barrel.
PISTON REMOVAL
Unscrew rear cap with the back end of the Disassembly/
Assembly Tool by turning counterclockwise and remove.
Pull piston spring and piston clear of the suppressor tube.
FIGURE 1
FIGURE 2
FIGURE 3
REAR
CAP
NUMBERED BAFFLES
SPACER
PISTON
SPRING
PISTON
SCREW ON
(CLOCKWISE)
UNSCREW OFF
(COUNTERCLOCKWISE)
BAFFLE CHAMBERPISTON CHAMBER
ALWAYS confirm weapon is unloaded and on SAFE
before attaching or removing
DISASSEMBLY/ASSEMBLY
TOOL
BAFFLE REMOVAL
TOOL
CAUTION: Suppressor may be extremely hot after firing
the weapon. Allow the suppressor to cool or wear appropriate
gloves before removing.
(1/2 x 28 shown)