Surewerx JET JDP Series User manual

MANUAL
Drill Presses
13-1/2" 3/4 HP
12 Speed Bench Drill Press
Product No. 200225
Mod No. JDP-13
13-1/2" 3/4 HP
12 Speed Floor Drill Press
Product No. 200275
Mod No. JDP-13F
17" 1 HP
16 Speed Floor Drill Press
Product No. 200278
Mod No. JDP-17F
22" 1-1/2 HP
12 Speed Floor Drill Press
Product No. 200357
Mod No. JDP-22F
M18-HT200225-357

2
Operating Instructions
Before operating the unit, please read this manual thoroughly, and retain it for future reference.
We thank you for your purchase of a JET Drill Press. It has been designed, engineered and manufactured to give
you the best possible dependability and performance. However, we'd like to remind you that faultless running is
entirely dependent upon rational use and careful maintenance, which will also spare the user time consuming
delays and costly repairs.
Your drill press was designed to give you a durable, reliable and easy to use product. With proper maintenance,
your JET machine will give you years of trouble-free operation.
Contents
Specifications................................................................3
Safety Rules...............................................................4, 5
Electrical Requirements................................................6
Getting to Know Your Drill Press...................................7
Assembly Instructions...............................................8, 9
Installing Chuck...........................................................10
Removing Chuck and Arbor .......................................10
Depth Stop...................................................................11
Spindle Speeds ...........................................................11
Changing Spindle Speeds and Tensioning Belt........11
Return Spring Adjustment...........................................12
Basic Operational Hints ..............................................12
Lubrication...................................................................12
Parts Lists ........................................................ 13, 15, 17
Replacement Parts.......................................... 13, 15, 17
Parts Breakdowns ........................................... 12, 14, 16

3
Warranty Policy
JET makes every effort to assure that its products meet high quality standards and warrants to the retail consumer/
purchaser of our products that each product is free from defects in material and workmanship. JET offers a TWO-
YEAR LIMITED WARRANTY on this product. Warranty does not apply to defects due directly or indirectly to misuse,
abuse, negligence or accidents, repairs or alterations performed outside our facilities or to a lack of maintenance.
Warranty Procedure
Any JET product for which there is a warranty claim should be returned PREPAID to an authorized JET distributor or
service centre. Authorized Warranty Depots are found at www.surewerx.com.
Specifications
Prod. No. 200225 200275 200278 200357
Mod. No. JDP-13 JDP-13F JDP-17F JDP-22F
Swing 13-1/4" 13-1/4" 17" 22"
Type Bench Floor Floor Floor
Chuck Size 1/32"-5/8" (1-16 mm) 1/32"-5/8" (1-16 mm) (5-200 mm) 3/4"
Drilling Capacity 5/8" 5/8" 5/8" 1-1/4"
Spindle Travel 3-1/16" 3-1/4" 3-3/8" 4-1/2"
Spindle Distance to Base 24" 48-3/4" 48-3/8" 49"
Spindle Distance to Table 17-1/2 " 31-1/2" 28½" 29"
Table Size 11-7/16" 11-7/16" 13-3/4" 16-1/2" x 18-3/4"
Table Tilt (R and L) 0° - 45° 0° - 45° 0° - 45° 0° - 45°
Spindle Taper JT3 JT3 JT3 MT3
Column Diameter 2-7/8" 2-7/8" 3-1/8" 3-5/8"
Number of Spindle Speeds 12 12 16 12
Range of Spindle Speeds (RPM) 280-3,000 280-3,000 220-3,380 180-4,200
Overall Height 38-1/2" 61-5/8" 64" 69-1/4"
Base size 10" x 16-1/2" 10" x 16-1/2" 12" x 19-3/4" 19-5/8" x 22-1/2"
Motor 3 / 4 H P, 1P H 3 / 4 H P, 1P H 1HP, 1PH 1. 5 H P, 1P H
115/230V 115/23 0V 115/2 30V 115/230V
Prewired 115V Prewired 115V Prewired 115V * Prewired 115V *
Product Weight 94 lbs. 107 lbs. 176 lbs. 353 lbs.
Shipping Weight 99 lbs. 112 lbs. 184 lbs. 373 lbs.
Standard Equipment: Built-in work lamp, drill chuck and key, positive depth stop.
* If converting to 230V power standard switch and face plate must be replaced with item
PDN-JDP-1338 Switch and item PDN-JDP-1725 Face Plate

4
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND WRENCHES. Always
check to see that keys and adjusting wrenches are
removed from tool before
turning it on.
3. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENTS. Don’t
use power tools in damp or wet locations, or expose
them to rain. Keep work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should be kept a
safe distance from work area.
6. MAKE WORKSHOP CHILD PROOF with padlocks,
master switches, or by removing starter keys.
7. DON’T FORCE TOOL. It will do the job better and safer
at the rate for which it was designed.
8. USE RIGHT TOOL. Don’t force tool or attachment to do
a job for which it was not designed.
9. WEAR PROPER APPAREL. Do not wear loose clothing,
gloves, neckties, rings, bracelets, or other jewellery
which may get caught in moving parts. Safety footwear is
recommended. Wear protective hair covering to contain
long hair.
10. ALWAYS USE SAFETY GLASSES. Also use face or
dust mask if cutting operation is dusty. Everyday
eyeglasses only have impact resistant lenses, they
are NOT safety glasses.
11. SECURE WORK. Use clamps or a vise to hold work at
all times. It’s safer than using your hand and it frees both
hands to operate tool.
12. DON’T OVERREACH. Keep proper footing and balance
at all times.
13. MAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for best and safest performance. Follow instructions
for lubricating and changing accessories.
14. DISCONNECT TOOLS before servicing (when changing
accessories, such as blades, bits, cutters, and the like).
15. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure switch is in off position before plugging in.
16. USE RECOMMENDED ACCESSORIES. The use of
improper accessories may cause risk of injury to persons.
17. NEVER STAND ON TOOL. Serious injury could
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
18. CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function – check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
19. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool until it comes to a
complete stop.
20. WOOD DUST CREATED BY CERTAIN
WOODWORKING TOOLS CAN BE HAZARDOUS TO
YOUR HEALTH. Operate machinery in a well-ventilated
area. Use of a dust collection system is
highly recommended.
Safety Rules
Additional Safety Rules for Drill Presses
1. Operate drill presses only if you are familiar with their
operation. If not, ask a qualified user.
2. Always shut off power to machine before making
any adjustments.
3. Machine must be properly grounded. Be sure to check
that electrical connections are compatible with machine.
4. Always check tightness of drill bit before operating. Failure
to do so could cause damage to machine and/or operator.
5. Always remove chuck key from chuck before
starting machine.
6. Always adjust table and/or depth stop to prevent drilling
into table. It is highly recommended to use a backing
piece when drilling through workpiece.
7. Secure workpiece to table with clamps or a vise to
prevent rotating with the drill bit.
WARNING
Do not wear gloves when operating drill press;
Serious injury could result.
Wear proper eye protection when operating this
or any power tool.
!

5
Electrical Requirements
Connecting to Power Source Outlet
This machine must be grounded while in use to protect
the operator from electric shock. Plug power cord into a
110-120v properly grounded type outlet protected by a
15 amp dual element time delay or circuit breaker.
Not all outlets are properly grounded. If you are not
sure that your outlet, as pictured below, is properly
grounded, have it checked by a qualified electrician.
To avoid electric shock, do not touch the metal
prongs on the plug, when installing or removing
the plug to or from the outlet.
Failure to properly ground this power tool can cause
electrocution or serious shock, particularly when
used in damp locations, or near metal plumbing. If
shocked, your reaction could cause your hands to
hit the cutting tool.
If power cord is worn or cut, or damaged in any
way, have it replaced immediately to avoid shock
or fire hazard.
Your drill press is currently wired by the factory to
operate on a 110/120v single phase circuit requiring a
15 amp breaker.
To operate on a 230v single phase circuit , please
refer to the motor name plate diagram for the wiring
connector for 230v.
This power tool is equipped with a 3-conductor cord and
grounding type plug. The ground conductor has a green
jacket and is attached to the tool housing at one end
and to the ground prong in the attachment plug at the
other end.
This plug requires a mating 3-conductor grounded type
outlet as shown.
The use of any extension cord will cause some loss
of power. To keep this to a minimum and to prevent
overheating and motor burnout, use the table below to
determine the minimum wire size (A.W.G.) extension
cord. Use only 3 wire extension cords which have
3-prong grounding type plugs and 3-pole receptacles
which accept the tool’s plug.
Extension Cord Length Wire Size A.W.G.
0 - 25 feet 16
26 - 50 feet 14
51 - 100 feet 12
WARNING
To avoid injury from unexpected
start up, do not use blower or
washing machine motors or any
motor with an automatic reset
overload protector.
!
3-Prong
Plug
Grounding
Prong
Always use a
properly grounded outlet

6
Getting to Know Your Drill Press
Splines
(Grooves)
Spindle
Bevel Scale
Table Bevel Lock
(Under Table)
Table Lock
Chuck
Light Socket
(Under)
Depth Scale
Depth Scale
Lock
Drill “On / Off” Switch
Spring Cap
Feed SpringFeed Spring
Adjustment
Support Lock
Wedge Key
Arbor Column Support
Column
Table
Feed Handle
Head Lock
Belt Tension Handle
(200278, 200357)
Belt Tension
Lock Handle
Column Collar
Rack
Table
Crank
Table
Support
Base
Chuck
Rack
(Teeth)
Chuck
Key

7
Refer to parts breakdown and/or descriptive
pictures for numbers indicated. Some floor models
come with the table bracket support already on
the column.
1. Place base (1) on flat and level surface.
2. Bolt column (2A) to base (1) using four hex
head bolts (5) supplied (position gear rack
(22) to right side of base - where applicable).
3. Remove rack ring (23) and rack (22) from
column using supplied hex socket wrench.
4. Install worm pinion (9) into bracket (6) so that
both gears engage smoothly.
5. Slide rack (22) into bracket (6). Then slide
this unfinished assembled unit onto column
(2A)(make sure unfinished portion of rack
is positioned on top and that rack is seated
properly in lower collar).
6. Slide rack ring (23) over column and fasten
with hex socket screw (24).
Assembly Instructions
23
23
22
5
2A
1
9
6
24
24

8
7. Install crank handle (10) onto previously installed
worm pinion (9) and tighten hex head bolt (11)
with wrench.
8. Install column lock handle (19) through plain side
of bracket (6) into threaded side and tighten.
9. Place head assembly (25) on top of column (2A).
CAUTION! Head assembly is heavy - use two
people or appropriate material handling
equipment when lifting.
10. Align head (25) to base (1) and tighten to column
(2A) with two socket screws (26) found on right
side of head.
11. Install three handle bars (43A) into handle
body (37).
12. Install table (21) into table bracket (12) and
tighten table lock handle (20).
13. Install 60 watt (max.) light bulb (not included)
into receptacle on bottom of head (25).
26
21
20
11
10
37
43A
12
19
25 2A

9
Installing Chuck
Unplug machine from power source
Note: Make sure the arbor nose is clean of any
oil or rust protectant before mounting chuck. On
models equipped with a Morse taper make sure all
rust protectant is cleaned off before inserting arbor.
You can inspect this by lowering the quill, using the
down feed handles, and rotating the spindle until
the knock out hole in the spindle lines up with the
knock out hole in the quill.
1. Slide small end of arbor (71) into chuck (72A).
2. Place long end of arbor (71) into spindle (58).
Rotate arbor to line up tang with spindle.
3. Raise table (21) to within 5 inches of chuck.
Place a block of wood on table and lower
chuck assembly to block of wood with handle
bar assembly (43A).
4. Press firmly to set assembly in spindle.
IMPORTANT: Spindle, arbor, and drill chuck have
to be clean of protective grease. Chuck and spindle
may not seat properly if these parts are not clean.
Removing Chuck and Arbor
Unplug machine from power source
1. Lower quill using handle bar assembly.
2. Align key hole in quill with key hole in spindle
by rotating spindle.
3. Insert wedge directly in aligned key holes and
tap lightly (place hand under chuck to catch
assembly before it hits table).
58
72A
71

10
Depth Stop
To drill multiple holes at the same preset depth, use
the depth stop. To set depth stop, simply advance
bit to lowest desired depth with the feed handle.
Using your other hand, advance nuts (614) on
depth stop until they are snug to seat (611).
Spindle will now advance only to this preset depth.
To release, simply advance nuts counterclockwise
to top of depth stop.
Spindle Speeds
A spindle speed and corresponding belt
arrangement chart can be found on the inside
of the pulley guard. Refer to this chart when
changing speeds.
Changing Spindle Speeds
and Tensioning Belt
Unplug machine from power source
1. Loosen two slide bar bolts (33).
2. Rotate tension adjuster (29) to bring motor
base (34) as close as possible to head (25).
3. Change belts to desired position on motor
pulley (79) and spindle pulley (70). Reference
speed chart (165) on inside of pulley cover
assembly (90A).
4. Rotate tension adjuster (29) to tension belt.
Hold tension adjuster (29) while checking
with thumb pressure for 1/2" deflection
midway between pulleys.
5. Tighten two slide bar bolts (33).
70
25 33 34
29
79
90A
165
25 33 34
29
614
611

11
Return Spring Adjustment
The return spring is adjusted at the factory and should
not need adjustment. If it does, follow these steps:
1. Disconnect drill press from power source.
2. Loosen two nuts (53, 106) approximately 1/4".
Do not remove.
3. Firmly hold coil spring cover (49A); pull out
and rotate until pin on return spring plate (52)
engages with next notch in coil spring cover (49A).
Turn counterclockwise to increase tension and
clockwise to decrease tension.
4. Tighten two nuts (53, 106) to hold in place - do not
overtighten. Nuts should not contact housing
when tight.
Basic Operational Hints
1. Always use a back-up piece of material (wood).
This protects the bit and the table. It also prevents
splintering of the workpiece.
2. Place material in such a way as to come into
contact with the left side of the column. This will
prevent the material from spinning.
WARNING: If workpiece is not long enough, use a
clamp or drill press vise that is securely fastened
into the table. Failure to do so may cause
serious injury.
3. Feed bit into material with only enough force to
allow drill bit to work. Feeding too slowly may
cause burning of workpiece. Feeding too quickly
may cause the motor to stop and/or the belts to
slip. It may also cause the workpiece to break free
from its clamps or the drill bit to break.
4. Generally speaking, the smaller the drill bit, the
greater the RPM required. Wood will require higher
speeds than metal. Metal is usually drilled at
slow speeds.
5. In dusty environments, frequently blow out any
dust that accumulates inside the motor.
Lubrication
All motor ball bearings are permanently lubricated.
No further lubrication is necessary.
Periodically lubricate the splines (grooves) in the
spindle (58) and teeth of the quill (56).
Periodically apply a light coating of grease to the
column and rack (table height adjuster).
49A
52
53 & 106

12
13-1/2" 3/4 HP
16 Speed Bench Drill Press
Product No. 200225
Mod No. JDP-13
13-1/2" 3/4 HP
16 Speed Floor Drill Press
Product No. 200275
Mod No. JDP-13F

13
Ref. Part No. Description Req.
01 PDN-JDP-1301 Base Bench Model 1
01 PDN-JDP-13F01 Base Floor Model 1
02 PDN-JDP-1302 Washer 4
03 PDN-JDP-1303 Bolt 4
04 PDN-JDP-13F04 Base Flange Floor Model 1
04 PDN-JDP-1304 Base Flange 1
05 PDN-JDP-1305 Set Screw 1
06 PDN-JDP-1306 Table Height Adjustable Handle 1
07 PDN-JDP-1307 Table Bracket 1
7-1 PDN-JDP-137-1 Scale 1
08 PDN-JDP-1308 Gear Shaft 1
09 PDN-JDP-1309 Gear 1
10 PDN-JDP-1310 Worm 1
11 PDN-JDP-1311 Clamp Blot 1
12 PDN-JDP-1312 Table Arm 1
12-1 PDN-JDP-1312-1 Zero Mark 1
13 PDN-JDP-1313 Set Screw 1
14 PDN-JDP-1314 Clamp Blot 1
15 PDN-JDP-1315 Washer 1
16 PDN-JDP-1316 Bolt 1
17 PDN-JDP-1317 Table 1
18 PDN-JDP-13F18 Rack Floor Model 1
18 PDN-JDP-1318 Rack 1
19 PDN-JDP-1319 Column 1
19 PDN-JDP-13F19 Column Floor Model 1
20 PDN-JDP-1320 Screw 1
21 PDN-JDP-1321 Rack Collar 1
22 PDN-JDP-1322 Feed Handle 3
23 PDN-JDP-1323 Handle Knob 3
24 PDN-JDP-1324 Pinion Shaft 1
25 PDN-JDP-1325 Scale Sleeve 1
26 PDN-JDP-1326 Head 1
26-1 PDN-JDP-1326-1 Set Screw 2
26-2 PDN-JDP-1326-2 Rubber Bushing 1
27 PDN-JDP-1327 Set Screw 2
28 PDN-JDP-1328 Belt Tension Adjustable Rod 1
28-1 PDN-JDP-1328-1 Spring 1
29 PDN-JDP-1329 Screw 4
30 PDN-JDP-1330 Screw 2
31 PDN-JDP-1331 Lamp Frame 1
32 PDN-JDP-1332 Lamp Holder 1
32-1 PDN-JDP-1332-1 Nut 1
33 PDN-JDP-1333 Nut 1
34 PDN-JDP-1334 Spring and Cap 1
35 PDN-JDP-1335 Switch Box 1
35-1 PDN-JDP-1335-1 Washer Pad 1
35-2 PDN-JDP-1335-2 Switch Mounting Plate 1
36 PDN-JDP-1336 Screw 3
37 PDN-JDP-1337 Lamp Switch 1
Ref. Part No. Description Req.
38 PDN-JDP-1338 Power Switch 1
39 PDN-JDP-1339 Screw 3
40 PDN-JDP-1340 Power Cord 1
40-1 PDN-JDP-1340-1 Motor Cord 1
41 PDN-JDP-1341 Snap Ring 2
42 PDN-JDP-1342 Driver Sleeve 1
43 PDN-JDP-1343 Ball Bearing 2
44 PDN-JDP-1344 Snap Ring 1
45 PDN-JDP-1345 Ball Bearing 1
46 PDN-JDP-1346 Rubber Gasket 1
47 PDN-JDP-1347 Quill 1
48 PDN-JDP-1348 Ball Bearing 1
49 PDN-JDP-1349 Depth Gauge Holder 1
49-1 PDN-JDP-1349-1 Nut 1
50 PDN-JDP-1350 Screw 1
51 PDN-JDP-1351 Spindle 1
52 PDN-JDP-1352 Punch 1
53 PDN-JDP-1353 Arbor 1
54 PDN-JDP-1354 Chuck 1
55 PDN-JDP-1355 Key 1
56 PDN-JDP-1356 Bolt 2
57 PDN-JDP-1357 Motor 1
58 PDN-JDP-1358 Screw 2
59 PDN-JDP-1359 Capacitor Holder 1
60 PDN-JDP-1360 Capacitor 1
61 PDN-JDP-1361 Pulley Guard 1
62 PDN-JDP-1362 Motor Pulley 1
63 PDN-JDP-1363 Set Screw 1
64 PDN-JDP-1364 Snap Ring 1
65 PDN-JDP-1365 Ball Bearing 1
66 PDN-JDP-1366 Snap Ring 1
67 PDN-JDP-1367 Middle Pulley 1
68 PDN-JDP-1368 V-Belt 1
69 PDN-JDP-1369 V-Belt 1
70 PDN-JDP-1370 Knob 1
71 PDN-JDP-1371 Screw 1
72 PDN-JDP-1372 Middle Pulley Frame 1
73 PDN-JDP-1373 Nut 1
74 PDN-JDP-1374 Spindle Pulley 1
75 PDN-JDP-1375 Screw 1
76 PDN-JDP-1376 Cord Fixer 1
77 PDN-JDP-1377 Cord Clamp 2
78 PDN-JDP-1378 Screw 1
79 PDN-JDP-1379 Screw 1
81 PDN-JDP-1381 Washer 1
82 PDN-JDP-1382 Nut 1
83 PDN-JDP-1383 Set Screw 1
84 PDN-JDP-1384 Depth Stick Rod 1
85 PDN-JDP-1385 Nut 2
Ordering Replacement Parts
Replacement parts may be ordered from your local distributor or
directly from SureWerx. When ordering replacement parts always
provide the following information:
1. The model number and serial number of the machine.
2. The part number.
3. The part name.
4. The desired quantity of the part.
13-1/2" 3/4 HP 16 Speed Bench Drill Press & 13-1/2" 3/4 HP 16 Speed Floor Drill Press

14
17" 1 HP
16 Speed Floor Drill Press
Product No. 200278
Mod No. JDP-17F

15
Ref. Part No. Description Req.
01 PDN-JDP-1701 Guard Cover 1
02 PDN-JDP-1702 Pan Head Screw 1
03 PDN-JDP-1703 Knob 1
04 PDN-JDP-1704 Nut 1
05 PDN-JDP-1705 Spindle Pulley 1
06 PDN-JDP-1706 V-Belt 1
07 PDN-JDP-1707 Middle Pulley 1
08 PDN-JDP-1708 Ball Bearing 2
09 PDN-JDP-1709 Retaining Ring 1
10 PDN-JDP-1710 Motor Pulley 1
11 PDN-JDP-1711 V-Belt 1
12 PDN-JDP-1712 Set Screw 1
13 PDN-JDP-1713 Screw 2
13-1 PDN-JDP-1713-1 Washer 2
14 PDN-JDP-1714 Pulley Support Plate 1
15 PDN-JDP-1715 Screw 2
16 PDN-JDP-1716 Cord Protector 1
17 PDN-JDP-1717 Electrical Cord 1
18 PDN-JDP-1718 Pulley Insert 1
19 PDN-JDP-1719 Retaining Ring 2
20 PDN-JDP-1720 Ball Bearing 2
21 PDN-JDP-1721 Bearing Spacer 1
22 PDN-JDP-1722 Pan Head Screw 3
23 PDN-JDP-1723 Start/Stop Switch 1
24 PDN-JDP-1724 Light Switch Push Button 1
25 PDN-JDP-1725 Switch Plate 1
25-1 PDN-JDP-1725-1 Rubber 1
26 PDN-JDP-1726 Pan Head Screw 3
27 PDN-JDP-1727 Box Switch Plate 1
28 PDN-JDP-1728 Cord Clamp 1
29 PDN-JDP-1729 Bolt 1
30 PDN-JDP-1730 Hex Nut 1
31 PDN-JDP-1731 Hex Nut 1
32 PDN-JDP-1732 Tension Spring Assembly 1
33 PDN-JDP-1733 Post Depth Stop 1
34 PDN-JDP-1734 Lock Nut 2
35 PDN-JDP-1735 Cord Clamp 1
36 PDN-JDP-1736 Lock Pin 1
37 PDN-JDP-1737 Screw 1
38 PDN-JDP-1738 Head 1
39 PDN-JDP-1739 Thumb Screw 1
40 PDN-JDP-1740 Retaining Ring 1
41 PDN-JDP-1741 Adjusting Lever 1
42 PDN-JDP-1742 Lever Shaft Assembly 1
43 PDN-JDP-1743 Set Screw 2
44 PDN-JDP-1744 Retaining Ring 1
45 PDN-JDP-1745 Motor Support Bracket 1
46 PDN-JDP-1746 Motor Support Bracket 1
47 PDN-JDP-1747 Electrical Cord 1
48 PDN-JDP-1748 Strain Relief 1
Ref. Part No. Description Req.
49 PDN-JDP-1749 Spring Washer 2
50 PDN-JDP-1750 Nut 2
51 PDN-JDP-1751 Hex Head Screw 4
52 PDN-JDP-1752 Motor Mount 1
53 PDN-JDP-1753 Motor 1
54 PDN-JDP-1754 Nut 4
55 PDN-JDP-1755 Rubber 1
56 PDN-JDP-1756 Junction Box 1
57 PDN-JDP-1757 Screw 1
58 PDN-JDP-1758 Retaining Ring 1
59 PDN-JDP-1759 Ball Bearing 1
60 PDN-JDP-1760 Rubber Washer 1
61 PDN-JDP-1761 Quill 1
62 PDN-JDP-1762 Thrust Bearing 1
63 PDN-JDP-1763 Screw 1
64 PDN-JDP-1764 Clamping Seat Depth Stop 1
65 PDN-JDP-1765 Lock Nut 1
66 PDN-JDP-1766 Spindle 1
67 PDN-JDP-1767 Arbor 1
68 PDN-JDP-1768 Chuck 1
68-1 PDN-JDP-1768-1 Key 1
69 PDN-JDP-1769 Screw 2
70 PDN-JDP-1770 Lamp Bracket 1
71 PDN-JDP-1771 Spacer 1
72 PDN-JDP-1772 Pinion, Feed 1
73 PDN-JDP-1773 Knob 3
74 PDN-JDP-1774 Handle 3
75 PDN-JDP-1775 Rack Collar 1
76 PDN-JDP-1776 Set Screw 1
77 PDN-JDP-1777 Column 1
78 PDN-JDP-1778 Rack Gear 1
79 PDN-JDP-1779 Elevating Worm 1
80 PDN-JDP-1780 Gear 1
81 PDN-JDP-1781 Bolt Clamp 1
82 PDN-JDP-1782 Table Arm Bracket 1
83 PDN-JDP-1783 Gear Shaft 1
84 PDN-JDP-1784 Set Screw 1
85 PDN-JDP-1785 Sleeve and Rod Assembly 1
86 PDN-JDP-1786 Table Bracket 1
87 PDN-JDP-1787 Set Screw 1
88 PDN-JDP-1788 Table Lock Handle 1
89 PDN-JDP-1789 Washer 1
90 PDN-JDP-1790 Blot 1
91 PDN-JDP-1791 Table 1
92 PDN-JDP-1792 Flange 1
93 PDN-JDP-1793 Bolt 4
94 PDN-JDP-1794 Spring Washer 4
95 PDN-JDP-1795 Bake 1
96 PDN-JDP-1796 Drift Key 1
Ordering Replacement Parts
Replacement parts may be ordered from your local distributor or directly from SureWerx.
When ordering replacement parts always provide the following information:
1. The model number and serial number of the machine.
2. The part number.
3. The part name.
4. The desired quantity of the part.
17" 1 HP 16 Speed Floor Drill Press

16
22" 1-1/2 HP
12 Speed Drill Press
Product No. 200357
Mod No. JDP-22F

17
Ref. Part No. Description Req.
01 PDN-JDP-2201 Spindle Pulley 1
02 PDN-JDP-2202 Nut 1
03 PDN-JDP-2203 Pulley Cover 1
04 PDN-JDP-2204 Screw 1
05 PDN-JDP-2205 Knob 1
06 PDN-JDP-2206 Bearing 2
07 PDN-JDP-2207 V-Belt 1
08 PDN-JDP-2208 Middle Pulley 1
09 PDN-JDP-2209 Retaining Ring 1
10 PDN-JDP-2210 V-Belt 1
11 PDN-JDP-2211 Retaining Ring 1
12 PDN-JDP-2212 Shaft Assembly 1
13 PDN-JDP-2213 Motor Pulley 1
14 PDN-JDP-2214 Screw 1
15 PDN-JDP-2215 Strain Relief 1
16 PDN-JDP-2216 Motor Cord 1
17 PDN-JDP-2217 Cord With Plug 1
18 PDN-JDP-2218 Pulley Insert 1
19 PDN-JDP-2219 Retaining Ring 2
20 PDN-JDP-2220 Bearing Spacer 1
21 PDN-JDP-2221 Bearing 2
22 PDN-JDP-2222 Bolt 1
23 PDN-JDP-2223 Hex Nut 1
24 PDN-JDP-2224 Hex Nut 1
25 PDN-JDP-2225 Spring and Cap 1
26 PDN-JDP-2226 Washer 1
27 PDN-JDP-2227 Start/Stop Switch 1
28 PDN-JDP-2228 Screw 3
29 PDN-JDP-2229 Light Switch 1
30 PDN-JDP-2230 Switch Plate 1
31 PDN-JDP-2231 Screw 2
32 PDN-JDP-2232 Screw 3
33 PDN-JDP-2233 Switch Box 1
34 PDN-JDP-2234 Nut 1
35 PDN-JDP-2235 Clamping Seat Depth Stop 1
36 PDN-JDP-2236 Screw 1
37 PDN-JDP-2237 Post Depth Stop 1
38 PDN-JDP-2238 Lock Nut 2
39 PDN-JDP-2239 Screw 2
40 PDN-JDP-2240 Motor Bracket Support 1
41 PDN-JDP-2241 Screw 1
42 PDN-JDP-2242 Cord Clamp 1
43 PDN-JDP-2243 Motor Bracket Support 1
44 PDN-JDP-2244 Retaining Ring 1
45 PDN-JDP-2245 Wing Screw 2
46 PDN-JDP-2246 Screw 1
47 PDN-JDP-2247 Adjusting Lever 1
48 PDN-JDP-2248 Retaining Ring 1
49 PDN-JDP-2249 Lever Shaft 1
50 PDN-JDP-2250 Hex Head Screw 4
51 PDN-JDP-2251 Motor Plate 1
52 PDN-JDP-2252 Spring Washer 2
Ref. Part No. Description Req.
53 PDN-JDP-2253 Hex Nut 2
54 PDN-JDP-2254 Motor 1
55 PDN-JDP-2255 Hex Nut 4
56 PDN-JDP-2256 Rubber 1
57 PDN-JDP-2257 Junction Box 1
58 PDN-JDP-2258 Screw 4
59 PDN-JDP-2259 Screw 1
60 PDN-JDP-2260 Set Screw 2
61 PDN-JDP-2261 Pan Screw 2
62 PDN-JDP-2262 Lamp Bracket 1
63 PDN-JDP-2263 Spacer 1
64 PDN-JDP-2264 Pinion Shaft 1
65 PDN-JDP-2265 Feeding Handle 3
66 PDN-JDP-2266 Knob 3
67 PDN-JDP-2267 Spindle Nut 1
68 PDN-JDP-2268 Bearing 1
69 PDN-JDP-2269 Quill Gasket 1
70 PDN-JDP-2270 Quill 1
71 PDN-JDP-2271 Thrust Bearing 1
72 PDN-JDP-2272 Bearing 1
73 PDN-JDP-2273 Spindle 1
74 PDN-JDP-2274 Drift Key 1
75 PDN-JDP-2275 Arbor 1
76 PDN-JDP-2276 Chuck 1
76-1 PDN-JDP-2276-1 Key 1
77 PDN-JDP-2277 Rack 1
78 PDN-JDP-2278 Screw 1
79 PDN-JDP-2279 Rack Collar 1
80 PDN-JDP-2280 Quill 1
81 PDN-JDP-2281 Table Bracket 1
82 PDN-JDP-2282 Table Handle 1
83 PDN-JDP-2283 Gear Shaft 1
84 PDN-JDP-2284 Set Screw 3
85 PDN-JDP-2285 Hex Head Screw 1
86 PDN-JDP-2286 Crank Sleeve Handle 1
87 PDN-JDP-2287 Tilt Scale 1
88 PDN-JDP-2288 Elevating Worm 1
89 PDN-JDP-2289 Helical Gear 1
90 PDN-JDP-2290 Zero Scale 1
91 PDN-JDP-2291 Table 1
92 PDN-JDP-2292 Hex Nut 2
93 PDN-JDP-2293 Washer 1
94 PDN-JDP-2294 Arm Stud 1
95 PDN-JDP-2295 Washer 1
96 PDN-JDP-2296 Arm Stud 1
97 PDN-JDP-2297 Bolt Hex Head 3
98 PDN-JDP-2298 Spring Washer 3
99 PDN-JDP-2299 Flange 1
100 PDN-JDP-22100 Base 1
101 PDN-JDP-22101 Cord for Clamp 1
102 PDN-JDP-22102 Cord Protect 1
103 PDN-JDP-22103 Head 1
Ordering Replacement Parts
Replacement parts may be ordered from your local distributor or directly from SureWerx.
When ordering replacement parts always provide the following information:
1. The model number and serial number of the machine.
2. The part number.
3. The part name.
4. The desired quantity of the part.
22" 1-1/2 HP 12 Speed Drill Press