Sealey VS709 User manual

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
BEARING RACE & SEAL
DRIVER SET - COMPOSITE
Model No: VS709
1. SAFETY INSTRUCTIONS
 WARNING! Ensure Health & Safety, local authority, and general worshop
practice regulations are adhered to when using this equipment.
 WARNING! Always wear approved eye protection when using the driver.
Failure to do so may result in serious injury. Normal spectacles are not
adequate protection.
 Familiarise yourself with the specific applications and limitations of the
driver, as well as any potential hazards.
 If unsure of the applications or limitations of the driver, contact your supplier.
 Ensure that the driver is the correct tool for the task. DO NOT use the driver
for any purpose other than that for which it is designed.
 Replace or repair damaged parts. Use genuine parts only. Unauthorised
parts may be dangerous and will invalidate the warranty.
 Ensure that the workpiece is stable and that there is adequate lighting.
 Maintain correct balance and footing. Ensure the floor is not slippery
and wear non-slip shoes.
 Use the correct size and type of hammer for the task. The recommended
diameter of hammer face is 10mm larger than tool head.
Check that the hammer shaft is in good order and is firmly secured in the
hammer head. Note that for seal installation a soft-faced hammer should be
adequate and will be less likely to damage the tool.
Make sure that the face of the hammer and the head of the tool are clean
and free from grease, oil, etc.
 Position the tool so that it is struck away from your body.
Strike the driver squarely on the head - DO NOT hit the tool off centre, or at
an angle (fig.1).
 DO NOT use the driver if it is bent, chipped, has a mushroom head, or
is otherwise damaged (fig.2).
 DO NOT strike the side of the driver body (fig.3).
 DO NOT use driver if any parts are damaged or missing as this may
cause failure and/or personal injury.
 DO NOT use the driver when you are tired or under the influence of alcohol,
drugs or intoxicating medication.
 Keep children and unauthorised persons away from the working area.
 When not in use, pack into the case, and store in a safe, dry, childproof
location.
Original Language Version VS709 Issue: 1 - 25/10/12
Incorrect
© Jack Sealey Ltd
Fig.1
Fig.3
Fig.2

3.1 Remove bolt (fig.4.B) from handle (fig.4.A).
3.2 Select the correct adaptor (fig.4.C), one which is slightly smaller than the diameter of the seal/bearing
race, and position it correctly on the handle, secure it using the bolt.
3.3 Place the seal/bearing race (fig.4.E or F) in the mouth of the housing (fig.4.D), place adaptor against it
and tap the driver handle to force it into place (fig.5).
3. OPERATION
2. INTRODUCTIOIN
ALWAYS WEAR SAFETY GOGGLES WHEN USING DRIVERS
Users of drivers are reminded that damage to the striking faces can take place and we
recommend that safety goggles are worn when using this tool.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version VS709 Issue: 1 - 25/10/12
fig.5
fig.4
© Jack Sealey Ltd
● Setofbearingandsealdrivers.
● Cleverlydesigned,idealforinstallationof
bearing races.
● Compositematerialpreventsdamage 
to bearing or housing.
● DriverSizesø:39.5,44.5,50,59,63,65,72,
 76,81mm