SURIA X Series User manual

In order to use the product safely, please read the instruction manual. In addition, please keep the
instruction manual properly.
Operation
Manual Book
X SERIES

SURIA ENGINEERING SOLUTIONS SDN BHD (1122001-T)
NO 1-2, JALAN 2/14, DATARAN TEMPLER, BANDAR BARU SELAYANG,
68100 BATU CAVES, SELANGOR DARUL EHSAN.
NO OFFICE: 03-6127 0974
ENGLISH

SURIA ENGINEERING SOLUTIONS SDN BHD (1122001-T)
NO 1-2, JALAN 2/14, DATARAN TEMPLER, BANDAR BARU SELAYANG,
68100 BATU CAVES, SELANGOR DARUL EHSAN.
NO OFFICE: 03-6127 0974
Summary
Thank you for purchasing a permanent magnet synchronous motor (PMSM)
industrial HVLS giant fan (X Series). This operation manual explains how to use the
product correctly. Please read this instruction carefully before use (installation,
wiring, operation, maintenance, inspection, etc). In addition, please use the product
after understanding the safety precautions of the product.
1. SAFETY ISSUES
General notes:
In order to explain the process of product installation, please operate the product
according to the instructions.
Danger
Please read the manual carefully before installation.
To prevent electric shock
Non-professionals are not allowed to repair, inspect or replace parts.
Do not conduct wiring operation within 1 minute after the power is turned
on or off, otherwise there will be electric shock danger (the capacitor will
also participate in the power supply within a short time after the power is
turned off).
When charging or moving the power supply, turn off the power supply first
and wait for all the indicator lights to go out for 1 minute before starting the
operation.
Warning
The controller of this product is matched according to the model. It is strictly
forbidden to use the controller without matching, which may cause damage to
the motor or controller. Before running the product, please confirm whether the
power the power supply is connected according to the label, and whether there
are obstacles within the operation range of the product that affect the operation
of the product. After running, check whether the rotation direction of the
product is correct (clockwise rotation seen from below). The product shall not
be operated in the bad environment of freezing, corrosion, explosion and dust
exceeding the standard seriously.

SURIA ENGINEERING SOLUTIONS SDN BHD (1122001-T)
NO 1-2, JALAN 2/14, DATARAN TEMPLER, BANDAR BARU SELAYANG,
68100 BATU CAVES, SELANGOR DARUL EHSAN.
NO OFFICE: 03-6127 0974
Ceiling Fan Installation
The installation and maintenance of products must be carried out by
professional training or experienced electrician with electrician certificate.
2. PRODUCT INTRODUCTION
Permanent magnet synchronous motor (PMSM) industrial HVLS giant fan (X
Series) is specially developed for energy saving and improving the comfort
of working environment. It is driven by a self-designed permanent magnet
motor with small size, light weight, high efficiency and energy saving, low
noise, frequency control, compact structure, beautiful appearance and
other characteristics. Widely used in industrial plants, logistics storage,
waiting rooms, exhibition halls, gymnasiums, supermarkets and other large
space places, as a new type of ceiling fan for space ventilation and personnel
cooling. It can push a large amount of airflow to the ground, forming a
certain height of airflow layer movement on the ground, thus contributing
to the overall air circulation, which is similar to the nature’s breeze system,
enjoying the intimate experience of natural wind.
ATTENTION. Please note all safety information in this instruction manual. Failure to
follow the instruction may result in death or serious injury. The company will not be
responsible for any damage caused by the customer’s failure to comply with the
contents in this instruction manual.
3. OPERATING LIMITS & SPECIFICATIONS
Operating limits
The company shall not be liable for damage caused by improper use or use
of products beyond the prescribed scope.
This product and accessories are selected and designed according to the
parameters provided by users. If the parameters are changed, please inform
us to confirm the feasibility.
The product is not allowed to operate in unstable areas such as high
frequency vibration areas. Please make sure that the installation location is
stable.
The product shall not be operated in harsh conditions such as freezing,
corrosion, explosion and excessive concentration of dust and gas.

SURIA ENGINEERING SOLUTIONS SDN BHD (1122001-T)
NO 1-2, JALAN 2/14, DATARAN TEMPLER, BANDAR BARU SELAYANG,
68100 BATU CAVES, SELANGOR DARUL EHSAN.
NO OFFICE: 03-6127 0974
Specifications and model
Permanent magnet synchronous motor (PMSM) HVLS industrial giant fan
specification model parameter in table below:
Table 1: Permanent Magnet Synchronous Motor (PMSM) Fan Technical Parameters
Model
Voltage
(v)
Power
(watt)
Max
Speed
(rpm)
No of
blade
Air Volume
(CMM)
Max
Coverage
(m2)
Weight
(kg)
X24
220-240
1100
55
6
15500
1700
111
X22
1100
60
6
14000
1600
107
X20
1000
65
6
11500
1000
103
X18
1000
70
6
11000
900
100
X16
750
80
5
10000
500
49
X14
750
90
5
7000
450
46
X12
370
100
5
5000
380
38
X10
370
120
5
4000
250
35
X8
370
130
5
3000
200
32
4. PARTS & INSTALLATION PROCESS
Components PMSM X Series (X8 - X16)

SURIA ENGINEERING SOLUTIONS SDN BHD (1122001-T)
NO 1-2, JALAN 2/14, DATARAN TEMPLER, BANDAR BARU SELAYANG,
68100 BATU CAVES, SELANGOR DARUL EHSAN.
NO OFFICE: 03-6127 0974
Components PMSM X Series (X18 - X24)
5. Controller & Wiring
Install the controller at the right position.
ATTENTION. The motor connected to the controller phase sequence must
not be wrong. Otherwise the motor reverse will affect the product effect.
Part:
Permanent magnet motor controller
1
Rubber sheathed cable
1
i. Terminal box connection
As shown in the figure, the controller lead-out line and motor lead-out line
identification are fixed on the terminal post, and no short circuit is allowed.
The ground wire is fixed on the fixing screw or the terminal box base and the
cover of the junction box shall be locked.
Figure 1 : terminal box connection

SURIA ENGINEERING SOLUTIONS SDN BHD (1122001-T)
NO 1-2, JALAN 2/14, DATARAN TEMPLER, BANDAR BARU SELAYANG,
68100 BATU CAVES, SELANGOR DARUL EHSAN.
NO OFFICE: 03-6127 0974
ii. Controller wiring
As shown in the figure, the top red frame is connected with the commercial
power (three-phase in the left figure and single phase in the right figure),
the middle red frame is connected with the motor (connected with the
junction box), and the right red frame is connected with the ground wire
(connected with the junction box).
Figure 2: Controller wiring
WARNING. It is forbidden to connect the commercial power directly to the
ceiling fan, and confirm whether the power supply voltage matches the
controller voltage.
Wiring Diagram
Figure 3 : Single phase input wiring diagram
Figure 4 : Three phase input wiring diagram

SURIA ENGINEERING SOLUTIONS SDN BHD (1122001-T)
NO 1-2, JALAN 2/14, DATARAN TEMPLER, BANDAR BARU SELAYANG,
68100 BATU CAVES, SELANGOR DARUL EHSAN.
NO OFFICE: 03-6127 0974
6. OPERATION & TROUBLESHOOTING
The controller interface is shown in the figure:
Figure 5 : Controller interface
Power on –operation
Power off –stop / reset
Speed up –ᴧpress speed +5
Slow down –ᴠpress speed -5
Table 2 : Fault diagnosis and countermeasures
Fault
Code
Description
Causes
Troubleshooting Method
OC
Overcurrent
protection
Output short
circuit test
Motor locked or
overloaded
Check whether the
motor cable is
damaged.
Switch off the MCB.
After 5 minutes,
switch on the MCB.
OE
DC overvoltage
protection
Power supply too
high
Too much
deceleration
inertia
Check whether the
rated voltage is input
Increase deceleration
time
PF1
Input open phases
protection
Phase loss of
input power
supply
Check whether the
power input is
normal
OL
Inverter overload
protection
Overload
Reduce the load
Increase the capacity
of frequency
converter
LU
Under voltage
protection
Low input voltage
Check whether the
power input is
normal

SURIA ENGINEERING SOLUTIONS SDN BHD (1122001-T)
NO 1-2, JALAN 2/14, DATARAN TEMPLER, BANDAR BARU SELAYANG,
68100 BATU CAVES, SELANGOR DARUL EHSAN.
NO OFFICE: 03-6127 0974
OH
Overheat
protection of
frequency
converter
The heat sink is
too dirty
The fan is broken
The ambient
temperature is
too high
Clean the inlet and
radiator
Replace the fan
Improve ventilation
Err2
Parameter
measurement
error
Motor not
connected during
parameter
measurement
Please connect the
motor correctly
Err3(4)
Current fault
before operation
There is current
alarm signal
before operation
Check whether the
cable connection is
reliable
Request
manufacturer’s
service
PFO
Output phase loss
The motor line is
disconnected
The motor is
broken
Inverter fault
Check the motor
connection wire
carefully
Replace the motor
Seek support from
manufacturers
GP
Grounding
protection
The motor cable
is damaged and
short circuited to
the ground
Motor insulation
damage, short
circuit to ground
Inverter fault
Replace the cable
Repair the motor
Seek support from
manufacturer
PCE
PMSM adjustment
fault
The acceleration
time is too short
Overload
Motor locked
rotor
Extend acceleration
time
Check whether the
motor is overloaded
ALM Light
Out-of-order
Report failure
STOP/RESET
Key
Failure
This instruction is
invalid
Loose cable
Inverter fault
Secure the cable
Turn off the power
and turn on again
after 1 minutes
Contact the
manufacturer

SURIA ENGINEERING SOLUTIONS SDN BHD (1122001-T)
NO 1-2, JALAN 2/14, DATARAN TEMPLER, BANDAR BARU SELAYANG,
68100 BATU CAVES, SELANGOR DARUL EHSAN.
NO OFFICE: 03-6127 0974
Regular inspection and maintenance
Electronic equipment and other components cannot be used permanently even
though in normal working conditions. If the service limit is exceeded, there will be a
change in characteristics or malfunction. To prevent this type of failure, periodic
inspections are required. It is recommended to check the machine every 6-12 month
after installation
Table 3: Regular inspection and maintenance schedule
No
Check the
object
Check the content
Solutions
1.
Overall
Dirt, dust
Parts are damaged/deformed
Parts that are discoloured due
to time
Replace damaged parts
Contact our after-sales
service
Remove dust/dirt with dry
towel.
2.
Motor
If there is abnormal vibration or sound
when the product is running
Turn off the fan, contact and
consult our after-sales
service
Inspect parts and fastening
connections and tighten all
screws
3.
Controller
system
Confirm whether the cooling fan
is stained with dust/dirt.
Check the wires and internal
connecting wires are
discoloured, damaged or
detached
Check the wire cladding is
damaged, cracked, or
discoloured
Check the connecting terminal is
worn, damaged or loose
Check the capacitance
expansion, discoloration,
cracking
Clean/replace the cooling fan
Repair/replace damaged
wires and connectors
Contact the company after
sale if unable to replace or
repair.
4.
LED
Operator
Check the operating parts
operate correctly
Check the operating part dirty
If LED or operation keys are
defective, please contact our
after-sales service.
Remove dust/dirt with dry
towel. Do no wipe with
water.